How to challenge the Red Seal exam in Yukon: hours and fees
How to challenge the Red Seal exam in Yukon: 1.5 times the apprenticeship hours, a $15 fee, monthly sittings in Whitehorse and the rewrite rules.
- Who decides
- Government of Yukon, Apprenticeship and Trade Certification
- What the route is called
- Challenge the journeyperson Certificate of Qualification exam
- Experience required
- 1.5 × the Yukon apprenticeship hours (9,600 for Plumber, for example)
- Application fee
- $15, non-refundable; $20 more for a practical exam
- Time to a decision
- 4 to 6 weeks
- Exam attempts
- Rebook after one month; a third attempt needs the Director’s approval, then more training
- The exam
- The Red Seal exam for your trade: multiple choice, 100 to 150 questions, four hours, 70% to pass.
References checked . Confirm application and exam requirements with the responsible authority.
Who can challenge the Red Seal exam in Yukon
Yukon’s rule is 1.5 times the work hours of the Yukon apprenticeship in your trade; the Apprentice Training and Tradesperson’s Qualifications Regulation (section 19) words it as having been engaged in the trade for at least one and one half times the term of the apprenticeship program. The authority’s own example: an apprentice plumber completes 6,400 hours (1,600 hours × 4 levels), so a challenger needs at least 9,600 hours as a plumber to sit the exam. Each trade’s levels and hours are on the one-page Trades designated in the Yukon information sheet (last updated 18 June 2025), and the figures by trade are listed below.
Self-employment hours count; ask your Industrial Training Consultant which documents to supply. The apply page sets no residency, citizenship, language or scope-of-trade rule and does not say whether you may apply from outside Canada, so ask the office before you plan around either. The regulation’s residency rule applies to apprenticeship agreements only, not to the Certificate of Qualification exam.
Hours required by trade in Yukon
These are the experience figures Government of Yukon, Apprenticeship and Trade Certification publishes for each trade, or the result of its published rule where the note says the figure is computed. Hours are hands-on work in the trade; the authority decides what counts. Each trade links to its practice exams.
Unless a trade’s note says otherwise:
- 1.5 × the Yukon apprenticeship hours, as the Ellis Chart reports them
| Trade | Experience required | Notes |
|---|---|---|
| Automotive Painter | 5,400 | 3,600 × 1.5 |
| Automotive Service Technician | 10,800 | 7,200 × 1.5 |
| Baker | 8,100 | 5,400 × 1.5 |
| Cabinetmaker | 10,800 | 7,200 × 1.5 |
| Carpenter | 9,600 | 6,400 × 1.5 |
| Construction Electrician (Electrician) | 10,800 | 7,200 × 1.5. Licensed through the Building Safety Branch |
| Cook | 8,100 | 5,400 × 1.5 |
| Floorcovering Installer | 7,200 | 4,800 × 1.5 |
| Gasfitter First Class (Class A) | 8,100 | 5,400 × 1.5. Licensed through the Building Safety Branch |
| Gasfitter Second Class (Class B) | 5,400 | 3,600 × 1.5. Licensed through the Building Safety Branch |
| Glazier | 10,800 | 7,200 × 1.5 |
| Hairstylist | 5,400 | 3,600 × 1.5. Practical exam required ($20) |
| Heavy Duty Equipment Technician (Off Road) | 8,100 | 5,400 × 1.5 |
| Industrial Electrician | 10,800 | 7,200 × 1.5. Licensed through the Building Safety Branch |
| Industrial Instrument Mechanic | 10,800 | 7,200 × 1.5 |
| Industrial Mechanic (Millwright) | 10,800 | 7,200 × 1.5 |
| Insulator (Heat and Frost) | 8,100 | 5,400 × 1.5 |
| Lather (Interior Systems Mechanic) | 8,100 | 5,400 × 1.5 |
| Machinist | 10,800 | 7,200 × 1.5 |
| Motor Vehicle Body Repairer (Metal and Paint) | 10,800 | 7,200 × 1.5 |
| Oil Burner Mechanic | 8,100 | 5,400 × 1.5. Licensed through the Building Safety Branch |
| Painter and Decorator | 7,200 | 4,800 × 1.5 |
| Partsperson | 8,100 | 5,400 × 1.5 |
| Plumber | 9,600 | The authority’s own example: 6,400 apprenticeship hours × 1.5 |
| Powerline Technician | 10,800 | 7,200 × 1.5 |
| Recreation Vehicle Service Technician | 8,100 | 5,400 × 1.5 |
| Refrigeration and Air Conditioning Mechanic | 10,800 | 7,200 × 1.5 |
| Roofer | 8,100 | 5,400 × 1.5 |
| Sheet Metal Worker | 10,800 | 7,200 × 1.5; the Ellis Chart lists 8,100, so confirm with the office; the chart also marks a practical final exam |
| Sprinkler System Installer | 10,800 | 7,200 × 1.5 |
| Steamfitter/Pipefitter | 9,600 | 6,400 × 1.5 |
| Transport Trailer Technician | 5,400 | 3,600 × 1.5 |
| Truck and Transport Technician | 8,100 | 5,400 × 1.5 |
| Welder | 8,100 | 5,400 × 1.5. Practical exam required ($20) |
Documents and forms you need
Have these ready before you start the application. Use the authority’s current forms; the names below are the ones Government of Yukon, Apprenticeship and Trade Certification uses.
- Application for examination for the Certificate of Qualification, the form on yukon.ca.
- A Trade Experience Verification form for your trade, completed by each employer and signed by both of you to confirm the information is accurate; one form per employer, handwritten or electronic. Forms are posted for 39 trades, from Automotive Painter to Welder.
- For periods of self-employment, the documents your Industrial Training Consultant lists.
- The non-refundable $15 application fee, paid by cash, cheque, debit or credit card when the office reviews your application.
How to apply in Yukon, step by step
The steps follow the order Government of Yukon, Apprenticeship and Trade Certification describes.
- Download and complete the Application for examination for the Certificate of Qualification form.
- Download a Trade Experience Verification form for your trade and have each employer complete and sign it, one form per employer. Include every form with your application. If you were self-employed, ask your Industrial Training Consultant for the list of required documents.
- Pay the non-refundable $15 application fee by cash, cheque, debit or credit card; the office processes the payment when it reviews your application at the Department of Education building’s front desk.
- Submit the application in person at the Education Building, 1000 Lewes Boulevard, Whitehorse (the parking entrance is on Hospital Road; open Monday to Friday, 8:30 am to 4:30 pm), by mail to Government of Yukon, Apprenticeship (E-13), Box 2703, Whitehorse, Yukon Y1A 2C6, or by emailing apprenticeship@yukon.ca for a secure upload link.
- Wait for verification, which takes 4 to 6 weeks; the office emails you with any questions. It then contacts you to schedule your written exam, and the practical exam if you are a hairstylist or welder. Sittings run monthly at the Department of Education building.
- Marking takes 4 to 6 business days and an Industrial Training Consultant contacts you with the result. If you pass, the Certificate of Qualification is mailed within 4 to 6 weeks; if you need proof sooner, the consultant gives you a letter with your journeyperson credentials.
What it costs in Yukon
Fees as published on 31 October 2026, on a page dated 7 January 2026: a non-refundable $15 application fee to apply for a Yukon Certificate of Qualification, and a non-refundable $20 practical examination fee for hairstylists and welders. Schedule B of the Apprentice Training and Tradesperson’s Qualifications Regulation frames the $15 as the non-refundable fee for writing the Certificate of Qualification examination, including the certificate and wallet card if you qualify for them, and the $20 as a practical examination fee paid in addition where both are required; it has no re-examination line, and no rewrite fee is published anywhere.
How long it takes
Plan around these published timelines; they start when the authority has a complete application.
- Verification and processing take 4 to 6 weeks from a complete application; the office emails you if it has questions.
- Exam sittings run monthly at the Department of Education building; the office contacts you to schedule your written and, where applicable, practical exam.
- Marking takes 4 to 6 business days, and an Industrial Training Consultant contacts you with the result.
- The Certificate of Qualification is mailed within 4 to 6 weeks of passing; a letter confirming your journeyperson credentials is available sooner on request.
- How long an approval to write stays valid is not published.
Writing the Red Seal exam in Yukon
Where and how the exam is written, and what to bring.
- The exam is written at the Department of Education building, 1000 Lewes Boulevard, Whitehorse, at monthly sittings.
- Hairstylists and welders also take a practical exam, for a $20 fee. The Ellis Chart also marks a practical final exam for Sheet Metal Worker in Yukon.
- The office points candidates to the Red Seal Exam Preparation Guide for the exam format and practice questions. Identification rules, exam languages and accommodations are not published on the apply page; ask the office when it schedules you.
If you do not pass
Rewrite rules are set by the authority. Before any rewrite, use the results breakdown to see which sections of the exam cost you marks.
- After a first unsuccessful attempt you can book the next date right away, but you must wait at least one month before writing again.
- A third attempt needs the approval of the Director of Apprenticeship.
- After a third unsuccessful attempt you are required to get more training before you can write again.
- The Apprentice Training and Tradesperson’s Qualifications Regulation puts it more loosely than the apply page: after a first or second unsuccessful attempt you wait a period of time the Director determines before applying for a further attempt, and the Director may require training before a fourth. The apply page’s one month and its approval rule for a third attempt are the office’s current practice.
- No rewrite fee is published, and the regulation’s fee schedule has no re-examination line.
Compulsory trades in Yukon
Yukon publishes no compulsory-trades list under that name. Its apply page says trades are regulated in the territory, that you must follow the regulations for your trade while working there, and that a Yukon Certificate of Qualification may be required as part of the licensing process. The regulated trades that need a licence include, but are not limited to, electrician (construction and industrial), gasfitter, oil burner mechanic, power engineer and elevator technician; the Building Safety Branch (buildingsafety@yukon.ca) handles that licensing. The Ellis Chart marks extra licensing for Construction Electrician, Industrial Electrician and both gasfitter classes in Yukon.
Applying from outside Canada or as a newcomer
What the authority publishes about applying before you arrive, residency, work authorization and experience gained abroad. Immigration and work permits are separate from trade certification.
- The apply page sets no residency, citizenship or work-authorization requirement and says nothing about applying from outside Canada or about experience gained abroad; the regulation’s residency requirement is attached to apprenticeship agreements, not to the Certificate of Qualification exam. Ask the office before you plan around either; the exam itself is written in Whitehorse.
- Self-employment hours count, with the documents your Industrial Training Consultant lists.
If you are already certified elsewhere in Canada
Yukon’s page describes two routes to a journeyperson Yukon Certificate of Qualification, with or without a Red Seal endorsement, and lists being able to work anywhere in Canada among the benefits of certification. If you already hold a Red Seal from another province or territory, ask the Apprenticeship and Trade Certification office about a Yukon certificate without writing again.
Good to know
Details that catch people out.
- Yukon calls the Certificate of Qualification a journeyperson ticket; getting it is being ticketed. The two ways to earn it are completing the Yukon apprenticeship, or applying with enough demonstrated working hours in a designated trade, including self-employment, and passing the exam.
- Not every trade on this site is designated in Yukon. The Ellis Chart shows no Yukon program for Boilermaker, Metal Fabricator, the three Ironworker trades, Tilesetter, Drywall Finisher and Plasterer, Concrete Finisher, Construction Craft Worker, Landscape Horticulturist, Mobile and Tower Crane Operator, the Heavy Equipment Operator trades, Agricultural Equipment Technician, Appliance Service Technician, Motorcycle Technician and Tool and Die Maker. Yukon posts no Trade Experience Verification form for Bricklayer, although the Ellis Chart shows a Yukon program with 8,100 trade qualifier hours; ask the office.
- Contact: the Apprenticeship and Trade Certification office at the Department of Education, apprenticeship@yukon.ca, 867-667-5298, or toll free in Yukon 1-800-661-0408, extension 5298.
Words Government of Yukon, Apprenticeship and Trade Certification uses
challenge the journeyperson Certificate of Qualification exam; journeyperson ticket; being ticketed; designated trade; Trade Experience Verification form; Industrial Training Consultant. The plain-language guide connects these to the words other provinces and tradespeople use.
Official pages this guide was read from
Rules and fees change. These are the pages Government of Yukon, Apprenticeship and Trade Certification publishes; confirm the current figures there before you pay or travel.
Prepare for the exam
Once Government of Yukon, Apprenticeship and Trade Certification approves you, you write the same Red Seal exam as a completing apprentice. It is built from your trade’s Red Seal Occupational Standard and its published exam breakdown, not from any school’s curriculum, so study from the standard and practise under time.
Try twelve free questions for your trade without an account, or Exam 1 in full with a free account, to see where you stand before your approval arrives.
Other provinces and territories
Moving, or comparing routes? Each of these guides covers one authority the same way: hours by trade, documents, steps, fees and rewrites.
- Challenge the Red Seal exam in British Columbia
- Challenge the Red Seal exam in Alberta
- Challenge the Red Seal exam in Saskatchewan
- Challenge the Red Seal exam in Manitoba
- Challenge the Red Seal exam in Ontario
- Challenge the Red Seal exam in Quebec
- Challenge the Red Seal exam in New Brunswick
- Challenge the Red Seal exam in Nova Scotia
- Challenge the Red Seal exam in Prince Edward Island
- Challenge the Red Seal exam in Newfoundland and Labrador
- Challenge the Red Seal exam in Northwest Territories
- Challenge the Red Seal exam in Nunavut
Common questions
How many hours do I need to challenge the Red Seal exam in Yukon?
1.5 times the work hours of the Yukon apprenticeship in your trade. Yukon’s own example is a plumber: the apprenticeship is 6,400 hours, so a challenger needs at least 9,600. Four-year, 7,200-hour trades such as electrician and millwright need 10,800; three-year trades such as welder, cook and heavy duty equipment technician need 8,100. The table on this page lists each designated trade.
What does it cost to challenge the Red Seal exam in Yukon?
A non-refundable $15 application fee, which covers the written exam, plus a non-refundable $20 practical exam fee if you are a hairstylist or welder. No rewrite fee is published.
Where and when is the Red Seal exam written in Yukon?
At the Department of Education building, 1000 Lewes Boulevard, Whitehorse. The office runs exam sittings monthly and contacts you to schedule yours once your application is approved.
How long does the Yukon application take?
The office verifies your experience in 4 to 6 weeks, then schedules you into a monthly sitting. Marking takes 4 to 6 business days and the certificate is mailed within 4 to 6 weeks of passing; a letter confirming your credentials is available sooner if you ask.
What happens if I do not pass the exam in Yukon?
You can book a second attempt right away but must wait at least one month before writing. A third attempt needs the Director of Apprenticeship’s approval, and after a third unsuccessful attempt you are required to get more training before writing again.
Do I need to live in Yukon to challenge the exam?
The apply page sets no residency requirement and does not address applying from outside Canada. The exam is written in Whitehorse and the office contacts you by email during verification, so ask the Apprenticeship and Trade Certification office before you plan around applying from elsewhere.
Which trades can be challenged in Yukon?
Any trade designated in Yukon, which includes electrician, plumber, steamfitter, sheet metal worker, refrigeration mechanic, both gasfitter classes, carpenter, welder, millwright, heavy duty equipment technician, automotive, truck and transport and parts trades, cook, baker, hairstylist, machinist, cabinetmaker and more. Boilermaker, the ironworker trades, the crane and heavy equipment operator trades and several others are not designated there.