Online Red Seal Exam Preparation, built on official standards
Auto Body and Collision Technician
Built on official standards for your trade
Practice exams split like the real exam.
Every answer explained.
- 6
- Practice exams
- 720
- Questions
- 240
- Flashcards
- 1,000+
- Flashcard Match
- 50+
- Trade math
- 100+
- Simulations
Practice exams
6 exams · 120 questions eachExam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works
6 practice exams and 720 original practice questions with answers and explanations, plus 240 flashcards in two exam-weighted sets, for the 120-question Auto Body and Collision Technician Red Seal exam. Timed or untimed, with pause and resume. 120 questions in the real exam · 4 hours · 70% pass mark.
Auto Body and Collision Technician sample exam questions
Take them as an exam12 free practice questions with answers and explanations. No account needed.
An estimate guide lists 2.4 hours for complete bumper-cover refinishing and 1.1 hours for the separately authorized colour blend on an adjacent fender. The guide states these operations are not included in each other. What refinish labour total should be carried forward before other operations?
2. A floor repair requires the original brushed seam texture. The selected repair system specifies a paintable brushable sealer over its prepared primed substrate, followed by the stated topcoats. Which material and application meet the appearance requirement?
3. A rail repair sheet specifies epoxy on cleaned exposed welds, seam sealer on the indicated primed seams and cavity wax in the enclosed rail after coating operations. Which location pairing follows that sheet?
4. A filler product sheet requires a P80 scratch on the prepared bare-steel repair area before application. The planned primer operation later requires the separate scratch refinement shown on its sheet. Which plan follows the filler preparation requirement?
5. A repairable plastic part is positively identified by its material code and manufacturer repair sheet as a weldable thermoplastic. A second part is identified as a thermoset with an approved adhesive repair. Which process assignment follows those verified identities?
6. A fixed, non-structural glass repair uses a specified butyl-tape system. Its preparation sheet requires complete old-tape removal and clean, dry compatible seating surfaces. Which preparation follows that requirement?
7. The axle service sheet specifies a new single-use nut, its listed torque sequence and staking into the shaft groove after tightening. Which assembly plan follows all three conditions?
8. A carpet replacement procedure requires restraint-system disabling and its specified energy-discharge wait before seat wiring is disconnected. The wiring retainers must be released before lifting the carpet. Which sequence preserves those requirements?
9. The selected repair system requires final P180 refinement on shaped filler and P400 preparation on adjacent cured clearcoat before the specified primer/sealer stages. Which abrasive plan follows both substrate requirements?
10. A two-component finishing putty has been weighed with the exact hardener ratio required by its sheet. The method calls for folding and spreading on a clean board until uniform, while avoiding entrained air. Which mixing action follows that method?
11. Three isolated dust nibs remain in otherwise acceptable cured clearcoat. The product repair procedure permits local denibbing within the verified available film thickness, followed by the stated compound and polish stages. Which scope minimizes unnecessary film removal?
12. A specified touch-up system for a steel-exposing chip requires cleaned prepared metal, compatible primer, thin colour applications with their flash intervals and the specified clear finish. Which sequence follows that layer order?
Start free
Interactive simulations
Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.
Learn to read the diagrams and schematic symbols used in your trade.
Animated section drawings show what happens inside the equipment as it runs.
Learn the correct name and job of every part.
Exam breakdown
Red Seal practice tests and exam prepThe official Auto Body and Collision Technician Red Seal exam, also called the interprovincial (IP) exam, has 120 questions across 7 topic blocks. Open a block to see its tasks and subtasks.
- 120
- Multiple choice questions
- 4 hours
- Writing time
- 70%
- Pass mark
APerforms common occupational skills12%1590
A-1 · Performs safety-related functions
2 official exam questions · 10 in the practice bank
- A-1.01 Maintains safe work environment
- A-1.02 Uses personal protective equipment (PPE) and safety equipment
A-2 · Uses and maintains tools and equipment
2 official exam questions · 25 in the practice bank
- A-2.01 Maintains hand and power tools
- A-2.02 Maintains frame and unibody repair and measuring equipment
- A-2.03 Uses lifting equipment
- A-2.04 Uses diagnostic equipment
- A-2.05 Maintains refinishing tools and equipment
A-3 · Uses and maintains welding equipment
2 official exam questions · 9 in the practice bank
- A-3.01 Uses welding equipment
- A-3.02 Maintains welding equipment
A-4 · Organizes work and uses documentation
2 official exam questions · 16 in the practice bank
- A-4.01 Prepares estimates and supplements
- A-4.02 Prepares repair plan
- A-4.03 Organizes parts, materials and work area
- A-4.04 Uses documentation
A-5 · Uses communication and mentoring techniques
1 official exam question · 6 in the practice bank
- A-5.01 Uses communication techniques
- A-5.02 Uses mentoring techniques
A-6 · Removes and installs trim and hardware
2 official exam questions · 8 in the practice bank
- A-6.01 Removes trim and hardware
- A-6.02 Installs trim and hardware
A-7 · Performs final inspections
2 official exam questions · 8 in the practice bank
- A-7.01 Performs final operational check
- A-7.02 Performs final quality control inspection
A-8 · Applies corrosion protection and sound deadening materials
2 official exam questions · 8 in the practice bank
- A-8.01 Applies corrosion inhibitors and undercoats
- A-8.02 Applies seam sealers and sound deadeners
BRepairs frame and structural components24%28168
B-9 · Prepares for repair and replacement of structural components
11 official exam questions · 66 in the practice bank
- B-9.01 Identifies extent of damage
- B-9.02 Removes components for access
- B-9.03 Performs vehicle setup
B-10 · Repairs, removes and installs structural components
12 official exam questions · 69 in the practice bank
- B-10.01 Repairs structural components
- B-10.02 Removes structural components
- B-10.03 Installs structural components
B-11 · Removes, installs and repairs structural and laminated glass
5 official exam questions · 33 in the practice bank
- B-11.01 Removes structural glass
- B-11.02 Installs structural glass
- B-11.03 Repairs laminated glass
CRepairs non-structural outer body panels and related components20%24144
C-12 · Removes, repairs and installs metal panels and components
11 official exam questions · 68 in the practice bank
- C-12.01 Prepares metal panels and components for repair
- C-12.02 Removes metal panels and components
- C-12.03 Repairs metal panels and components
- C-12.04 Installs metal panels and components
C-13 · Removes, repairs and installs plastic and composite panels and components
9 official exam questions · 60 in the practice bank
- C-13.01 Prepares plastic and composite panels and components for repair
- C-13.02 Removes plastic and composite panels and components
- C-13.03 Repairs plastic and composite panels and components
- C-13.04 Installs plastic and composite panels and components
C-14 · Removes and installs non-structural glass
4 official exam questions · 16 in the practice bank
- C-14.01 Removes non-structural glass
- C-14.02 Installs non-structural glass
DRepairs mechanical, electrical and alternative-fuel system components11%1378
D-15 · Deactivates and reactivates alternative-fuel systems
2 official exam questions · 12 in the practice bank
- D-15.01 Deactivates alternative-fuel systems
- D-15.02 Reactivates alternative-fuel systems
D-16 · Removes and installs mechanical components
7 official exam questions · 30 in the practice bank
- D-16.01 Removes mechanical components
- D-16.02 Installs mechanical components
D-17 · Removes, repairs and installs electrical and electronic components
4 official exam questions · 36 in the practice bank
- D-17.01 Removes electrical components
- D-17.02 Repairs damaged wires and protective coverings
- D-17.03 Installs electrical components
- D-17.04 Services advanced electronic components
ERepairs interior components and services restraint systems10%1272
E-18 · Repairs and replaces interior components
5 official exam questions · 32 in the practice bank
- E-18.01 Repairs interior components
- E-18.02 Replaces interior components
E-19 · Services supplemental restraint systems (SRS)
7 official exam questions · 40 in the practice bank
- E-19.01 Services seat belt restraint systems
- E-19.02 Services air bags and related components
FPerforms refinishing procedures18%22132
F-20 · Prepares surface
5 official exam questions · 40 in the practice bank
- F-20.01 Performs initial preparation
- F-20.02 Masks surface
- F-20.03 Strips surface
- F-20.04 Sands surface
F-21 · Uses repair materials
3 official exam questions · 14 in the practice bank
- F-21.01 Mixes repair materials
- F-21.02 Applies repair materials
F-22 · Prepares refinishing equipment
3 official exam questions · 14 in the practice bank
- F-22.01 Prepares spray booth
- F-22.02 Performs spray gun setup
F-23 · Prepares refinishing materials
4 official exam questions · 16 in the practice bank
- F-23.01 Mixes refinishing materials
- F-23.02 Performs colour adjustments
F-24 · Applies refinishing materials
5 official exam questions · 38 in the practice bank
- F-24.01 Applies sealers
- F-24.02 Applies base coat
- F-24.03 Applies single-stage paint
- F-24.04 Applies clear coat
F-25 · Performs post-refinishing functions
2 official exam questions · 10 in the practice bank
- F-25.01 Removes masking materials
- F-25.02 Corrects surface imperfections
GPerforms detailing and cleaning5%636
G-26 · Details exterior
4 official exam questions · 24 in the practice bank
- G-26.01 Removes minor imperfections
- G-26.02 Polishes vehicle
- G-26.03 Touches up stone chips
G-27 · Cleans vehicle
2 official exam questions · 12 in the practice bank
- G-27.01 Cleans exterior
- G-27.02 Cleans interior
Source: the official Auto Body and Collision Technician standard and exam breakdown. Check your own requirements with your province or territory.
Questions about Auto Body and Collision Technician exam prep
Study guideIs there a free Auto Body and Collision Technician Red Seal practice test?
Yes. Auto Body and Collision Technician Exam 1 is a full practice exam of 120 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.
Is there a Auto Body and Collision Technician practice test with answers?
Yes. Every Auto Body and Collision Technician practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.
How many questions are on the Auto Body and Collision Technician Red Seal exam?
The official Auto Body and Collision Technician Red Seal exam has 120 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 84 of 120 questions correct.
What topics are on the Auto Body and Collision Technician Red Seal exam?
The published exam breakdown has 7 Major Work Activities (MWAs) or blocks: A, Performs common occupational skills (15 questions); B, Repairs frame and structural components (28 questions); C, Repairs non-structural outer body panels and related components (24 questions); D, Repairs mechanical, electrical and alternative-fuel system components (13 questions); E, Repairs interior components and services restraint systems (12 questions); F, Performs refinishing procedures (22 questions); G, Performs detailing and cleaning (6 questions).
Use the full trade breakdown to review the tasks in every MWA, and the official RSOS or NOA for the subtasks of each task.
Can I challenge the Auto Body and Collision Technician Red Seal exam without an apprenticeship?
Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 120-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 8,000 in Ontario to 10,800 in Yukon (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.
How do your Auto Body and Collision Technician practice exams follow the official breakdown?
Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.
What are Flashcard Match and Question Match?
Flashcard Match deals a board of Auto Body and Collision Technician flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Auto Body and Collision Technician practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.
How many Auto Body and Collision Technician practice exams are included?
Pass Your Red Seal includes 6 practice exams and 720 original practice questions for Auto Body and Collision Technician. Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 120 questions on the official exam.
Are Auto Body and Collision Technician flashcards included?
Yes. Every Auto Body and Collision Technician plan includes 240 flashcards in two exam-weighted sets of 120 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard (RSOS) – Auto Body and Collision Technician (2019) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.
Can I try Auto Body and Collision Technician practice questions for free?
Yes. Try 12 free Auto Body and Collision Technician questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.
How much does Auto Body and Collision Technician study access cost?
Study access for Auto Body and Collision Technician costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.
Challenge the Auto Body and Collision Technician exam without an apprenticeship
How it worksExperienced workers in the auto body and collision technician trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.
| Province or territory, with its guide | Hours to challenge | Apprenticeship and certification |
|---|---|---|
| British Columbia | 9,675 | Apprenticeship 7,200 hours · voluntary certification |
| Alberta Auto Body Technician | 9,630 | Apprenticeship 7,200 hours · compulsory certification |
| Saskatchewan | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Manitoba | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Ontario Auto Body and Collision Damage Repairer | 8,000 | Apprenticeship 8,000 hours · compulsory certification |
| Quebec | Not shown | |
| New Brunswick | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Nova Scotia | 10,800 | Apprenticeship 7,200 hours · compulsory certification |
| Prince Edward Island Motor Vehicle Body Repairer (Metal and Paint) | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Newfoundland and Labrador | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Yukon | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Northwest Territories | 9,000 | Apprenticeship 7,200 hours · voluntary certification |
| Nunavut Motor Vehicle Body Repair | 9,000 | Apprenticeship 7,200 hours · voluntary certification |
Source: Ellis Chart, Auto Body and Collision Technician, published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.