Pass Your Red Seal
Exams

Online Red Seal Exam Preparation, built on official standards

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

Gasfitter – Class A

Built on official standards for your trade

Practice exams split like the real exam.
Every answer explained.

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

4
Practice exams
400
Questions
200
Flashcards
1,000+
Flashcard Match
50+
Trade math
100+
Simulations
Try Gasfitter – Class A free12 sample questions now, or Exam 1 with a free account12 sample questionsFree Exam 1

Practice exams

4 exams · 100 questions each

Exam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works

4 practice exams and 400 original practice questions with answers and explanations, plus 200 flashcards in two exam-weighted sets, for the 100-question Gasfitter – Class A Red Seal exam. Timed or untimed, with pause and resume. 100 questions in the real exam · 4 hours · 70% pass mark.

Gasfitter – Class A sample exam questions

Take them as an exam

12 free practice questions with answers and explanations. No account needed.

Sample 1 Gasfitter – Class A, free sample

A differential manometer has its high port at the burner manifold and low port at the combustion chamber. It reads +0.85 kPa. What does that reading represent?

Answer Manifold pressure above chamber pressure.
Why The instrument displays high-port pressure minus low-port pressure. Here the manifold is 0.85 kPa above the chamber. Reversing the ports reverses the sign; neither port references atmosphere in this connection.
2. Two threaded elbows have centres 600 mm apart. Each fitting's centre-to-end distance is 38 mm and required thread engagement is 16 mm. What cut-length relationship is correct?
Answer Subtract both fitting offsets; add both thread engagements.
Why Cut length is 600 - 2(38) + 2(16) = 556 mm. Centre-to-end dimensions reduce the exposed length, while the pipe extends into both fittings. Subtracting engagement shortens it incorrectly; adding fitting offsets reverses the geometry.
3. A vent-material allowance uses ΔL = αLΔT. For a 3 m section, α = 70 × 10^-6 per °C and a rise of 80°C, what thermal growth should the layout allow before applying the maker's joint rules?
Answer About 16.8 mm of axial growth from the stated temperature rise.
Why ΔL = 70 × 10^-6 × 3 × 80 = 0.0168 m = 16.8 mm. The 168 mm and 1.68 mm alternatives misplace a decimal; 5.6 mm omits the length factor. Manufacturer movement provisions still govern the actual joint arrangement.
4. A straight duct must span 1,200 mm between two faces. Each end inserts 35 mm into a collar beyond its face. What developed straight length is required before seam allowances?
Answer Use 1,270 mm to include both collar insertion allowances.
Why The duct extends 35 mm beyond each face, so 1200 + 35 + 35 = 1270 mm. Subtracting allowances or counting only one end gives the wrong geometry. Seam allowances are expressly excluded.
5. A burner needs 90° actuator travel in 15 seconds or less and 12 N·m torque. X provides 15 N·m in 25 seconds; Y provides 10 N·m in 10 seconds; Z provides 14 N·m in 12 seconds. All have the required approval and fail action. Which selection is justified?
Answer Select Z because it meets both travel time and torque.
Why Only Z satisfies both constraints. X is too slow and Y lacks torque. A torque adjustment does not establish an unlisted travel speed. The specification must be met as a combination, not by optimizing one figure.
6. During the manufacturer's hot-refractory test, an infrared flame detector continues indicating flame after the approved checks confirm flame extinction and fuel isolation. No adjacent burner operates. The indication fades as refractory cools and disappears when the specified optical test blocks its view. What should be investigated first?
Answer The detector's response to hot refractory and its specified sighting arrangement.
Why The optical blocking and cooling relationship points to hot refractory radiation influencing the detector. Investigate suitability, sighting and the manufacturer's required corrective checks; do not simply relax the protection. Pilot pressure, orifice size and regulator capacity do not explain an optical indication with confirmed flame extinction and fuel isolation.
7. A capillary control's mounting instructions specify a minimum bend radius. Its proposed bracket would force a tighter bend without enough free capillary length. What must change?
Answer Reposition the approved mounting arrangement to preserve the specified bend radius.
Why Preserve the specified geometry and protected sensing assembly. Pulling, field splicing without approval or flattening can damage the capillary system. Resolve location/routing using the manufacturer's permitted arrangement.
8. A steam-trap selection table uses pressure difference across the trap. The supplied operating pressures are 800 kPa upstream and 200 kPa downstream on the same gauge basis. What difference should be used?
Answer 600 kPa, subtracting downstream pressure from upstream pressure.
Why The operating difference is 800 − 200 = 600 kPa. Using either pressure alone or adding them misstates the available differential. Capacity, temperature and startup conditions still require the actual trap selection data.
9. A CNG component will see 20 MPa maximum service pressure. Its documented temperature and gas compatibility are satisfactory. Candidate maximum working pressures are 16, 18, 21 and 25 MPa. Which is the lowest adequate listed pressure rating?
Answer Select the 21 MPa rating to cover the maximum stated service pressure.
Why The rating must cover the stated 20 MPa maximum, making 21 MPa the lowest listed adequate rating. Normal flowing pressure cannot replace maximum service pressure. A 25 MPa component provides additional margin but is not the lowest adequate choice.
10. An isolated rigid gas-test section is at 100 kPa gauge and 293 K. Atmospheric pressure is 100 kPa. It cools to 288 K without loss; assume ideal-gas behaviour. What gauge pressure is predicted?
Answer About 96.6 kPa, using absolute temperature and returning to gauge pressure.
Why Initial absolute pressure is 200 kPa. Final absolute pressure is 200 × 288/293 = 196.59 kPa, so gauge pressure is 96.59 kPa. Gauge-only scaling, omitted atmospheric subtraction and reversed ratios are wrong. This prediction does not by itself prove tightness.
11. A commissioning record requires draft in pascals. The verified instrument reads a magnitude of 2.5 inches water column. Using the supplied 249 Pa per inch water column, what magnitude should be recorded?
Answer 622.5 Pa, multiplying the indicated magnitude by the supplied factor.
Why 2.5 × 249 = 622.5 Pa. Division and decimal shifting are incorrect conversions. Record the actual sign/reference separately as required; the question asks only magnitude and supplies the conversion constant.
12. An intermittent burner trip log shows the airflow input opens 0.3 seconds before fuel-valve de-energization and flame loss. Which event should guide initial fault isolation?
Answer Investigate the airflow-proof interruption as the initiating event.
Why Chronology suggests airflow-proof loss initiates the safety shutdown, followed by fuel closure and flame loss. The later flame event cannot explain the earlier input change from this evidence. Normal output removal and multiple recorded events do not justify those replacements.

Start free

Interactive simulations

Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.

Diagrams and symbols

Learn to read the diagrams and schematic symbols used in your trade.

How things work

Animated section drawings show what happens inside the equipment as it runs.

Terminology

Learn the correct name and job of every part.

Exam breakdown

Red Seal practice tests and exam prep

The official Gasfitter – Class A Red Seal exam, also called the interprovincial (IP) exam, has 100 questions across 7 topic blocks. Open a block to see its tasks and subtasks.

100
Multiple choice questions
4 hours
Writing time
70%
Pass mark
Major Work Activity% of examReal examPractice bank
APerforms common occupational skills5%520

A-1 · Performs safety-related functions

1 official exam question · 4 in the practice bank

  • A-1.01 Maintains safe work environment
  • A-1.02 Uses personal protective equipment (PPE) and safety equipment

A-2 · Uses tools and equipment

2 official exam questions · 8 in the practice bank

  • A-2.01 Uses hand and power tools
  • A-2.02 Uses technical instruments and testers
  • A-2.03 Uses access equipment
  • A-2.04 Operates lifting, rigging and hoisting equipment

A-3 · Organizes work

2 official exam questions · 8 in the practice bank

  • A-3.01 Interprets documents
  • A-3.02 Selects systems, equipment and components
  • A-3.03 Plans for installation, service and maintenance

A-4 · Uses communication and mentoring techniques

0 official exam questions · 0 in the practice bank

  • A-4.01 Uses communication techniques
  • A-4.02 Uses mentoring techniques
BInstalls fuel piping and tubing systems9%936

B-5 · Selects and installs piping for fuel systems

5 official exam questions · 20 in the practice bank

  • B-5.01 Selects piping for fuel systems
  • B-5.02 Prepares piping for fuel systems
  • B-5.03 Installs piping for fuel systems

B-6 · Selects and installs tubing for fuel systems

4 official exam questions · 16 in the practice bank

  • B-6.01 Selects tubing for fuel systems
  • B-6.02 Prepares tubing for fuel systems
  • B-6.03 Installs tubing for fuel systems
CInstalls venting and air supply systems13%1352

C-7 · Selects and installs venting systems

5 official exam questions · 20 in the practice bank

  • C-7.01 Selects materials for venting systems
  • C-7.02 Prepares materials for venting systems
  • C-7.03 Installs venting systems

C-8 · Selects and installs air supply systems

5 official exam questions · 20 in the practice bank

  • C-8.01 Selects materials for air supply systems
  • C-8.02 Prepares materials for air supply systems
  • C-8.03 Installs air supply systems

C-9 · Selects and installs draft control systems

3 official exam questions · 12 in the practice bank

  • C-9.01 Selects components for draft control systems
  • C-9.02 Installs components for draft control systems
DInstalls controls and electrical systems19%1976

D-10 · Selects and installs combustion control systems

4 official exam questions · 16 in the practice bank

  • D-10.01 Selects combustion control components
  • D-10.02 Installs combustion control components

D-11 · Selects and installs flame safeguard systems

5 official exam questions · 20 in the practice bank

  • D-11.01 Selects flame safeguard components
  • D-11.02 Installs flame safeguard components

D-12 · Selects and installs operating control systems

4 official exam questions · 16 in the practice bank

  • D-12.01 Selects operating control components
  • D-12.02 Installs operating control components

D-13 · Selects and installs electrical systems

4 official exam questions · 16 in the practice bank

  • D-13.01 Selects electrical components
  • D-13.02 Installs electrical components

D-14 · Selects and installs automation and instrumentation control systems

2 official exam questions · 8 in the practice bank

  • D-14.01 Selects automation and instrumentation control components
  • D-14.02 Installs automation and instrumentation control components
EInstalls and converts fuel systems, appliances and ancillary equipment13%1352

E-15 · Selects, installs and converts fuel systems, appliances and ancillary equipment

6 official exam questions · 24 in the practice bank

  • E-15.01 Selects appliances and ancillary equipment
  • E-15.02 Installs appliances and ancillary equipment
  • E-15.03 Installs fuel conversion components

E-16 · Selects and installs propane and natural gas storage, handling and dispensing systems

5 official exam questions · 20 in the practice bank

  • E-16.01 Selects propane and natural gas storage, handling and dispensing systems
  • E-16.02 Installs propane and natural gas storage, handling and dispensing systems

E-17 · Selects and installs other fuel storage, handling and dispensing systems

2 official exam questions · 8 in the practice bank

  • E-17.01 Selects other fuel storage, handling and dispensing systems
  • E-17.02 Installs other fuel storage, handling and dispensing systems
FTests and commissions fuel systems, appliances and ancillary equipment23%2392

F-18 · Tests fuel delivery systems

9 official exam questions · 36 in the practice bank

  • F-18.01 Selects testing equipment and procedures
  • F-18.02 Tests fuel piping and tubing systems

F-19 · Commissions fuel systems, appliances and ancillary equipment

14 official exam questions · 56 in the practice bank

  • F-19.01 Performs start-up procedures
  • F-19.02 Performs testing, adjusting and balancing procedures
  • F-19.03 Completes commissioning report and handover
GServices fuel systems, appliances and ancillary equipment18%1872

G-20 · Maintains fuel systems, appliances and ancillary equipment

7 official exam questions · 28 in the practice bank

  • G-20.01 Inspects system components and operation
  • G-20.02 Performs maintenance activities

G-21 · Repairs fuel systems, appliances and ancillary equipment

8 official exam questions · 32 in the practice bank

  • G-21.01 Diagnoses system components and operation
  • G-21.02 Replaces components
  • G-21.03 Verifies operation

G-22 · Decommissions fuel systems, appliances and ancillary equipment

3 official exam questions · 12 in the practice bank

  • G-22.01 Disconnects appliances and ancillary equipment
  • G-22.02 Removes appliances and ancillary equipment

Source: the official Gasfitter – Class A standard and exam breakdown. Check your own requirements with your province or territory.

Questions about Gasfitter – Class A exam prep

Study guide
Is there a free Gasfitter – Class A Red Seal practice test?

Yes. Gasfitter – Class A Exam 1 is a full practice exam of 100 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.

Is there a Gasfitter – Class A practice test with answers?

Yes. Every Gasfitter – Class A practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.

How many questions are on the Gasfitter – Class A Red Seal exam?

The official Gasfitter – Class A Red Seal exam has 100 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 70 of 100 questions correct.

What topics are on the Gasfitter – Class A Red Seal exam?

The published exam breakdown has 7 Major Work Activities (MWAs) or blocks: A, Performs common occupational skills (5 questions); B, Installs fuel piping and tubing systems (9 questions); C, Installs venting and air supply systems (13 questions); D, Installs controls and electrical systems (19 questions); E, Installs and converts fuel systems, appliances and ancillary equipment (13 questions); F, Tests and commissions fuel systems, appliances and ancillary equipment (23 questions); G, Services fuel systems, appliances and ancillary equipment (18 questions).

Can I challenge the Gasfitter – Class A Red Seal exam without an apprenticeship?

Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 100-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 4,500 in British Columbia to 10,800 in New Brunswick (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.

How do your Gasfitter – Class A practice exams follow the official breakdown?

Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.

What are Flashcard Match and Question Match?

Flashcard Match deals a board of Gasfitter – Class A flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Gasfitter – Class A practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.

How many Gasfitter – Class A practice exams are included?

Pass Your Red Seal includes 4 practice exams and 400 original practice questions for Gasfitter – Class A. Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 100 questions on the official exam.

Are Gasfitter – Class A flashcards included?

Yes. Every Gasfitter – Class A plan includes 200 flashcards in two exam-weighted sets of 100 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard – Gasfitter – Class A (2024) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.

Can I try Gasfitter – Class A practice questions for free?

Yes. Try 12 free Gasfitter – Class A questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.

How much does Gasfitter – Class A study access cost?

Study access for Gasfitter – Class A costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.

Challenge the Gasfitter – Class A exam without an apprenticeship

How it works

Experienced workers in the gasfitter – class a trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.

Experience required to challenge the Gasfitter – Class A Red Seal exam
Province or territory, with its guideHours to challengeApprenticeship and certification
British Columbia4,500Apprenticeship 3,600 hours · compulsory certification
Alberta7,020Apprenticeship 5,400 hours · compulsory certification
SaskatchewanNo challenge route
Manitoba
Gasfitter
10,800Apprenticeship 7,200 hours · voluntary certification
OntarioNot shown
QuebecQuebec certificate firstCompulsory certification
New Brunswick10,800Apprenticeship 6,720 hours · voluntary certification
Nova Scotia8,100Apprenticeship 5,400 hours · voluntary certification
Prince Edward Island6,000Voluntary certification
Newfoundland and Labrador8,100Voluntary certification
Yukon
Gasfitter (First Class)
8,100Apprenticeship 5,400 hours · voluntary certification
Northwest Territories7,200Apprenticeship 5,400 hours · voluntary certification
Nunavut
Gasfitter (First Class)
7,200Apprenticeship 5,400 hours · voluntary certification

Source: Ellis Chart, Gasfitter – Class A, published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.