Online Red Seal Exam Preparation, built on official standards
Truck and Transport Mechanic
Built on official standards for your trade
Practice exams split like the real exam.
Every answer explained.
- 6
- Practice exams
- 810
- Questions
- 270
- Flashcards
- 1,000+
- Flashcard Match
- 50+
- Trade math
- 100+
- Simulations
Practice exams
6 exams · 135 questions eachExam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works
6 practice exams and 810 original practice questions with answers and explanations, plus 270 flashcards in two exam-weighted sets, for the 135-question Truck and Transport Mechanic Red Seal exam. Timed or untimed, with pause and resume. 135 questions in the real exam · 4 hours · 70% pass mark.
Truck and Transport Mechanic sample exam questions
Take them as an exam12 free practice questions with answers and explanations. No account needed.
A spindle-nut procedure gives its torque sequence for clean threads and a named lubricant. Inspection finds dry threads with removable surface corrosion, and no dry-torque alternative is published. What should precede using the listed sequence?
2. Oil is found in engine coolant. The approved isolation test shows an oil-cooler core leaking from its oil passage into its coolant passage at the specified differential pressure; the other tested interfaces pass. What fault has been demonstrated?
3. A trailer supply circuit continues losing air after its reservoirs have charged. Under the approved isolation test, capping at the tractor connection stops the loss; connecting the trailer restores it. Tractor controls pass their checks. What region is localized for the next leak search?
4. During the approved cranking test, which meter connection measures voltage drop along the high-current positive feed from the battery to the starter?
5. The body-builder electrical guide requires accessory feeds from its designated distribution point with branch protection sized for each conductor. An added winch and lamps bypass that branch protection. Which repair plan follows the guide?
6. The selected axle setup procedure establishes pinion depth and preload, then ring-gear backlash with carrier preload, followed by loaded pattern verification. Why is a backlash reading within range insufficient by itself for acceptance?
7. The selected steering service procedure specifies an initial engine-off purge with the steer axle safely supported, followed by a prescribed low-speed powered check without holding the stops. Which sequence follows this procedure?
8. A bonded-windshield adhesive system requires its specified preparation of bare pinch-weld scratches and a minimum drive-away time determined from actual installation conditions. What release evidence satisfies those two controls?
9. A trailer rear-axle brake circuit is over-applied during empty running. In a controlled test, its verified load-signal pressure is low, but the proportioning-valve delivery remains at the full-load value for the same service command. Chambers release normally when the command is removed. What is localized?
10. The approved electric-compressor replacement procedure requires high-voltage isolation and absence-of-voltage verification, plus lubricant L specified by exact part number. The new unit accepts the same refrigerant as a belt-driven unit using lubricant P. Which repair controls remain required?
11. A steering metering unit has manufacturer timing marks for the drive link and metering set, plus a specified centring-spring arrangement. Which reassembly plan preserves its designed relationship?
12. An approved low-voltage service-fixture test simulates an open high-voltage interlock loop while all high-voltage parts remain safely isolated and covered. The controller should command contactors open and record the specified interlock fault. Which result verifies that requested logic response?
Start free
Interactive simulations
Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.
Learn to read the diagrams and schematic symbols used in your trade.
Animated section drawings show what happens inside the equipment as it runs.
Learn the correct name and job of every part.
Exam breakdown
Red Seal practice tests and exam prepThe official Truck and Transport Mechanic Red Seal exam, also called the interprovincial (IP) exam, has 135 questions across 11 topic blocks. Open a block to see its tasks and subtasks.
- 135
- Multiple choice questions
- 4 hours
- Writing time
- 70%
- Pass mark
ACommon Occupational Skills6%848
A-1 · Performs safety-related functions.
2 official exam questions · 9 in the practice bank
- A-1.01 Maintains safe work environment
- A-1.02 Uses personal protective equipment (PPE) and safety equipment
- A-1.03 Implements specific safety protocols for hybrid and electric vehicles (EV)
A-2 · Uses and maintains tools and equipment.
3 official exam questions · 17 in the practice bank
- A-2.01 Uses hand, power, measuring, testing, and diagnostic tools
- A-2.02 Uses shop equipment
- A-2.03 Uses hoisting, lifting and staging equipment
- A-2.04 Uses welding and cutting equipment
- A-2.05 Uses electronic devices and systems for diagnostics and programming
A-3 · Performs routine trade activities.
2 official exam questions · 18 in the practice bank
- A-3.01 Uses documentation and reference materials
- A-3.02 Maintains fluids and lubricants
- A-3.03 Services hoses, tubing and fittings
- A-3.04 Services filters
- A-3.05 Services bearings and seals
- A-3.06 Uses fasteners and sealing devices
A-4 · Uses communication and mentoring techniques.
1 official exam question · 4 in the practice bank
- A-4.01 Uses communication techniques
- A-4.02 Uses mentoring techniques
BServices, diagnoses and repairs engines and supporting systems16%21126
B-5 · Services, diagnoses and repairs base engines.
3 official exam questions · 18 in the practice bank
- B-5.01 Services base engines
- B-5.02 Diagnoses base engines
- B-5.03 Repairs base engines
B-6 · Services, diagnoses and repairs lubrication systems.
2 official exam questions · 15 in the practice bank
- B-6.01 Services lubrication systems
- B-6.02 Diagnoses lubrication systems
- B-6.03 Repairs lubrication systems
B-7 · Services, diagnoses and repairs intake systems.
2 official exam questions · 12 in the practice bank
- B-7.01 Services intake systems
- B-7.02 Diagnoses intake systems
- B-7.03 Repairs intake systems
B-8 · Services, diagnoses and repairs exhaust systems.
3 official exam questions · 18 in the practice bank
- B-8.01 Services exhaust systems
- B-8.02 Diagnoses exhaust systems
- B-8.03 Repairs exhaust systems
B-9 · Services, diagnoses and repairs engine management systems.
4 official exam questions · 21 in the practice bank
- B-9.01 Services engine management systems
- B-9.02 Diagnoses engine management systems
- B-9.03 Repairs engine management systems
B-10 · Services, diagnoses and repairs fuel delivery systems.
3 official exam questions · 18 in the practice bank
- B-10.01 Services fuel delivery systems
- B-10.02 Diagnoses fuel delivery systems
- B-10.03 Repairs fuel delivery systems
B-11 · Services, diagnoses and repairs engine retarder systems.
2 official exam questions · 12 in the practice bank
- B-11.01 Services engine retarder systems
- B-11.02 Diagnoses engine retarder systems
- B-11.03 Repairs engine retarder systems
B-12 · Services, diagnoses and repairs cooling systems.
2 official exam questions · 12 in the practice bank
- B-12.01 Services cooling systems
- B-12.02 Diagnoses cooling systems
- B-12.03 Repairs cooling systems
CServices, diagnoses and repairs air systems and brake systems13%17102
C-13 · Services, diagnoses and repairs air systems.
9 official exam questions · 54 in the practice bank
- C-13.01 Services air systems
- C-13.02 Diagnoses air systems
- C-13.03 Repairs air systems
C-14 · Services, diagnoses and repairs brake systems.
8 official exam questions · 48 in the practice bank
- C-14.01 Services brake systems
- C-14.02 Diagnoses brake systems
- C-14.03 Repairs brake systems
DServices, diagnoses and repairs electrical and electronic systems16%22132
D-15 · Services, diagnoses and repairs batteries systems.
3 official exam questions · 18 in the practice bank
- D-15.01 Services battery systems
- D-15.02 Diagnoses battery systems
- D-15.03 Repairs battery systems
D-16 · Services, diagnoses and repairs charging systems.
4 official exam questions · 24 in the practice bank
- D-16.01 Services charging systems
- D-16.02 Diagnoses charging systems
- D-16.03 Repairs charging systems
D-17 · Services, diagnoses and repairs spark ignition systems.
2 official exam questions · 15 in the practice bank
- D-17.01 Services spark ignition systems
- D-17.02 Diagnoses spark ignition systems
- D-17.03 Repairs spark ignition systems
D-18 · Services, diagnoses and repairs starting systems.
4 official exam questions · 24 in the practice bank
- D-18.01 Services starting systems
- D-18.02 Diagnoses starting systems
- D-18.03 Repairs starting systems
D-19 · Services, diagnoses and repairs electrical components and accessories.
5 official exam questions · 27 in the practice bank
- D-19.01 Services electrical components and accessories
- D-19.02 Diagnoses electrical components and accessories
- D-19.03 Repairs electrical components and accessories
D-20 · Services, diagnoses and repairs vehicle management systems and electronic components.
4 official exam questions · 24 in the practice bank
- D-20.01 Services vehicle management systems and electronic components
- D-20.02 Diagnoses vehicle management systems and electronic components
- D-20.03 Repairs vehicle management systems and electronic components
EServices, diagnoses and repairs drive trains13%17102
E-21 · Services, diagnoses and repairs clutches.
2 official exam questions · 12 in the practice bank
- E-21.01 Services clutches
- E-21.02 Diagnoses clutches
- E-21.03 Repairs clutches
E-22 · Services, diagnoses and repairs manual transmission and transfer cases.
3 official exam questions · 18 in the practice bank
- E-22.01 Services manual transmissions and transfer cases
- E-22.02 Diagnoses manual transmissions and transfer cases
- E-22.03 Repairs manual transmissions and transfer cases
E-23 · Services, diagnoses and repairs automatic transmissions.
2 official exam questions · 12 in the practice bank
- E-23.01 Services automatic transmissions
- E-23.02 Diagnoses automatic transmissions
- E-23.03 Repairs automatic transmissions
E-24 · Services, diagnoses and repairs automated transmissions.
4 official exam questions · 21 in the practice bank
- E-24.01 Services automated transmissions
- E-24.02 Diagnoses automated transmissions
- E-24.03 Repairs automated transmissions
E-25 · Services, diagnoses and repairs driveline systems.
2 official exam questions · 12 in the practice bank
- E-25.01 Services driveline systems
- E-25.02 Diagnoses driveline systems
- E-25.03 Repairs driveline systems
E-26 · Services, diagnoses and repairs drive axle assemblies.
3 official exam questions · 18 in the practice bank
- E-26.01 Services drive axle assemblies
- E-26.02 Diagnoses drive axle assemblies
- E-26.03 Repairs drive axle assemblies
E-27 · Services, diagnoses and repairs drive train retarders.
1 official exam question · 9 in the practice bank
- E-27.01 Services drive train retarders
- E-27.02 Diagnoses drive train retarders
- E-27.03 Repairs drive train retarders
FServices, diagnoses and repairs steering, chassis/frames, suspensions, tires, wheels and hubs13%18108
F-28 · Services, diagnoses and repairs steering systems.
5 official exam questions · 27 in the practice bank
- F-28.01 Services steering systems
- F-28.02 Diagnoses steering systems
- F-28.03 Repairs steering systems
F-29 · Services, diagnoses and repairs chassis/frames.
2 official exam questions · 15 in the practice bank
- F-29.01 Services chassisframes
- F-29.02 Diagnoses chassisframes
- F-29.03 Repairs chassisframes
F-30 · Services, diagnoses and repairs suspension.
4 official exam questions · 24 in the practice bank
- F-30.01 Services suspensions
- F-30.02 Diagnoses suspensions
- F-30.03 Repairs suspensions
F-31 · Services, diagnoses and repairs hitches and couplers.
3 official exam questions · 18 in the practice bank
- F-31.01 Services hitches and couplers
- F-31.02 Diagnoses hitches and couplers
- F-31.03 Repairs hitches and couplers
F-32 · Services, diagnoses and repairs tires, wheels and hubs.
4 official exam questions · 24 in the practice bank
- F-32.01 Services tires, wheels and hubs
- F-32.02 Diagnoses tires, wheels and hubs
- F-32.03 Repairs tires, wheels and hubs
GServices, diagnoses and repairs cabs4%530
G-33 · Services, diagnoses and repairs interior cab components.
3 official exam questions · 18 in the practice bank
- G-33.01 Services interior cab components
- G-33.02 Diagnoses interior cab components
- G-33.03 Repairs interior cab components
G-34 · Services, diagnoses and repairs exterior cab components.
2 official exam questions · 12 in the practice bank
- G-34.01 Services exterior cab components
- G-34.02 Diagnoses exterior cab components
- G-34.03 Repairs exterior cab components
HServices, diagnoses and repairs trailers6%848
H-35 · Services, diagnoses and repairs trailer components and accessories.
5 official exam questions · 27 in the practice bank
- H-35.01 Services trailer components and accessories
- H-35.02 Diagnoses trailer components and accessories
- H-35.03 Repairs trailer components and accessories
H-36 · Services, diagnoses and repairs heating and refrigeration systems.
3 official exam questions · 21 in the practice bank
- H-36.01 Services heating and refrigeration systems
- H-36.02 Diagnoses heating and refrigeration systems
- H-36.03 Repairs heating and refrigeration systems
IServices, diagnoses and repairs climate control systems5%742
I-37 · Services, diagnoses and repairs heating and ventilation systems.
3 official exam questions · 18 in the practice bank
- I-37.01 Services heating and ventilation systems
- I-37.02 Diagnoses heating and ventilation systems
- I-37.03 Repairs heating and ventilation systems
I-38 · Services, diagnoses and repairs air conditioning systems.
4 official exam questions · 24 in the practice bank
- I-38.01 Services air conditioning systems
- I-38.02 Diagnoses air conditioning systems
- I-38.03 Repairs air conditioning systems
JServices, diagnoses and repairs hydraulic systems6%848
J-39 · Services, diagnoses and repairs hydraulic components
8 official exam questions · 48 in the practice bank
- J-39.01 Services hydraulic systems
- J-39.02 Diagnoses hydraulic systems
- J-39.03 Repairs hydraulic systems
KServices, diagnoses and repairs hybrid and electric vehicles (EV)2%424
K-40 · Services, diagnoses and repairs hybrid vehicles
2 official exam questions · 12 in the practice bank
- K-40.01 Services hybrid vehicles
- K-40.02 Diagnoses hybrid vehicles
- K-40.03 Repairs hybrid vehicles
K-41 · Services, diagnoses and repairs electric vehicles (EV)
2 official exam questions · 12 in the practice bank
- K-41.01 Services electric vehicles (EV)
- K-41.02 Diagnoses electric vehicles (EV)
- K-41.03 Repairs electric vehicles (EV)
Source: the official Truck and Transport Mechanic standard and exam breakdown. Check your own requirements with your province or territory.
Questions about Truck and Transport Mechanic exam prep
Study guideIs there a free Truck and Transport Mechanic Red Seal practice test?
Yes. Truck and Transport Mechanic Exam 1 is a full practice exam of 135 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.
Is there a Truck and Transport Mechanic practice test with answers?
Yes. Every Truck and Transport Mechanic practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.
How many questions are on the Truck and Transport Mechanic Red Seal exam?
The official Truck and Transport Mechanic Red Seal exam has 135 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 95 of 135 questions correct.
What topics are on the Truck and Transport Mechanic Red Seal exam?
The published exam breakdown has 11 Major Work Activities (MWAs) or blocks: A, Common Occupational Skills (8 questions); B, Services, diagnoses and repairs engines and supporting systems (21 questions); C, Services, diagnoses and repairs air systems and brake systems (17 questions); D, Services, diagnoses and repairs electrical and electronic systems (22 questions); E, Services, diagnoses and repairs drive trains (17 questions); F, Services, diagnoses and repairs steering, chassis/frames, suspensions, tires, wheels and hubs (18 questions); G, Services, diagnoses and repairs cabs (5 questions); H, Services, diagnoses and repairs trailers (8 questions); I, Services, diagnoses and repairs climate control systems (7 questions); J, Services, diagnoses and repairs hydraulic systems (8 questions); K, Services, diagnoses and repairs hybrid and electric vehicles (EV) (4 questions).
Use the full trade breakdown to review the tasks in every MWA, and the official RSOS or NOA for the subtasks of each task.
Can I challenge the Truck and Transport Mechanic Red Seal exam without an apprenticeship?
Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 135-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 6,720 in Ontario to 10,800 in Newfoundland and Labrador (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.
How do your Truck and Transport Mechanic practice exams follow the official breakdown?
Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.
What are Flashcard Match and Question Match?
Flashcard Match deals a board of Truck and Transport Mechanic flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Truck and Transport Mechanic practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.
How many Truck and Transport Mechanic practice exams are included?
Pass Your Red Seal includes 6 practice exams and 810 original practice questions for Truck and Transport Mechanic. Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 135 questions on the official exam.
Are Truck and Transport Mechanic flashcards included?
Yes. Every Truck and Transport Mechanic plan includes 270 flashcards in two exam-weighted sets of 135 cards. Each set follows the Major Work Activity and task question counts of the official Truck and Transport Mechanic Red Seal Occupational Standard (2022) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.
Can I try Truck and Transport Mechanic practice questions for free?
Yes. Try 12 free Truck and Transport Mechanic questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.
How much does Truck and Transport Mechanic study access cost?
Study access for Truck and Transport Mechanic costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.
Challenge the Truck and Transport Mechanic exam without an apprenticeship
How it worksExperienced workers in the truck and transport mechanic trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.
| Province or territory, with its guide | Hours to challenge | Apprenticeship and certification |
|---|---|---|
| British Columbia | 9,495 | Apprenticeship 7,200 hours · voluntary certification |
| Alberta Heavy Equipment Technician - Truck and Transport Mechanic | 6,750 | Apprenticeship 5,220 hours · compulsory certification |
| Saskatchewan | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Manitoba | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Ontario Truck and Coach Technician | 6,720 | Apprenticeship 6,720 hours · compulsory certification |
| Quebec | Quebec certificate first | Compulsory certification |
| New Brunswick | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Nova Scotia | 10,800 | Apprenticeship 7,200 hours · compulsory certification |
| Prince Edward Island | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Newfoundland and Labrador | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Yukon Truck and Transport Technician | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Northwest Territories Heavy Equipment Technician - Truck and Transport Mechanic | 7,200 | Apprenticeship 5,400 hours · voluntary certification |
| Nunavut Heavy Equipment Technician - Truck and Transport Mechanic | 7,200 | Apprenticeship 5,400 hours · voluntary certification |
Source: Ellis Chart, Truck and Transport Mechanic, published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.