Online Red Seal Exam Preparation, built on official standards
Welder
Built on official standards for your trade
Practice exams split like the real exam.
Every answer explained.
- 6
- Practice exams
- 750
- Questions
- 250
- Flashcards
- 1,000+
- Flashcard Match
- 50+
- Trade math
- 100+
- Simulations
Practice exams
6 exams · 125 questions eachExam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works
6 practice exams and 750 original practice questions with answers and explanations, plus 250 flashcards in two exam-weighted sets, for the 125-question Welder Red Seal exam. Timed or untimed, with pause and resume. 125 questions in the real exam · 4 hours · 70% pass mark.
Welder sample exam questions
Take them as an exam12 free practice questions with answers and explanations. No account needed.
During oxy-fuel torch servicing, a parts list identifies a reverse-flow check valve separately from a flashback arrestor. Which statement correctly distinguishes their protective functions?
2. In a welding helmet fitted with a clear retaining lens, a filter lens and a heat gasket, how do the retaining lens and heat gasket differ?
3. A hollow pedestal requires an internal stiffener weld and a specified visual inspection using a 30 mm inspection head. Installing the end plate leaves only a 22 mm access bore, and the approved plan provides no alternate inspection method. Which sequence preserves the required access?
4. An arc-welding power source lists both input power factor and power-conversion efficiency. Which ratio defines its input power factor at a stated operating condition?
5. An oblong opening has semicircular ends of 9 mm radius. The drawing dimensions 76 mm between the two end centres. What overall opening length must be laid out?
6. An approved butt-joint detail requires a 55° included groove angle. One member is already prepared at 20° from square; the other must complete the included angle. Each member must retain a 3 mm root face. Which preparation meets the detail for the second member?
7. An oxygen regulator’s supplied characteristic predicts a 1 kPa outlet increase for each 100 kPa inlet decrease at the test flow. At that unchanged flow, readings move from 1600/400 kPa inlet/outlet to 800/408 kPa. Temperature remains steady, and a separate closed-seat test at fixed inlet pressure shows no downstream rise. Which interpretation fits both tests?
8. A plasma CNC uses a full-kerf-width compensation entry and verified waste-side paths. Repeated external 100.0 mm features measure 100.6 mm; internal 60.0 mm openings measure 59.4 mm. Top and bottom measurements agree, kerf width is uniform, and independent X/Y travel checks match commanded distances. Which first compensation trial best fits the combined pattern?
9. A thermocouple record for a shielded metal arc welding (SMAW) qualification coupon shows 500°C at 1 s and 800°C at 4 s while heating, a peak of 1100°C at 7 s, then 800°C at 11 s and 500°C at 23 s while cooling. What is the recorded t₈/₅ cooling time?
10. A Harris Model 32 flowmeter is being set up for CO₂. Its catalogue specifies separate argon, CO₂ and nitrogen scales and a 50 psig compensation condition. The supply regulator currently delivers 20 psig and the argon scale is facing the operator. Which setup matches the stated calibration conditions?
11. An Aspect 230, code 12732, uses standard four-step GTAW with restart disabled. The required sequence is to hold starting current, complete the upslope to operating current, weld, then hold finishing current before ending the arc. Which trigger sequence achieves it?
12. Before loading a SAW positioner, a setup sheet uses the published Koike HD400VF example plate: 31000 lb is permitted at a combined centre-of-gravity height of 18 in perpendicular to the table, and rotation moment is limited to 480000 lb-in. The work weighs 24000 lb and its fixture 4000 lb. Their combined CG is 18 in above the table and offset 20 in parallel to it. How does the setup compare with these two limits?
Start free
Interactive simulations
Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.
Learn to read the diagrams and schematic symbols used in your trade.
Animated section drawings show what happens inside the equipment as it runs.
Learn the correct name and job of every part.
Exam breakdown
Red Seal practice tests and exam prepThe official Welder Red Seal exam, also called the interprovincial (IP) exam, has 125 questions across 4 topic blocks. Open a block to see its tasks and subtasks.
- 125
- Multiple choice questions
- 4 hours
- Writing time
- 70%
- Pass mark
APerforms Common Occupational Skills16%20120
A-1 · Maintains tools and equipment
4 official exam questions · 24 in the practice bank
- A-1.01 Maintains hand, power, layout and measuring tools
- A-1.02 Maintains stationary machinery
- A-1.03 Maintains thermal cutting equipment
- A-1.04 Maintains welding equipment
A-2 · Uses access and material handling equipment
3 official exam questions · 14 in the practice bank
- A-2.01 Uses access equipment
- A-2.02 Uses material handling equipment
A-3 · Performs safety-related activities
4 official exam questions · 17 in the practice bank
- A-3.01 Performs hazard assessments
- A-3.02 Maintains safe work environment
- A-3.03 Uses personal protective equipment (PPE) and safety equipment
A-4 · Organizes work
3 official exam questions · 18 in the practice bank
- A-4.01 Uses documentation and reference material
- A-4.02 Interprets drawings and welding symbols
- A-4.03 Plans job tasks
- A-4.04 Organizes materials
A-5 · Performs routine trade activities
6 official exam questions · 47 in the practice bank
- A-5.01 Performs quality inspection
- A-5.02 Marks welds, materials and parts
- A-5.03 Controls temperature of weldments
- A-5.04 Stores welding consumables and gas cylinders
- A-5.05 Selects welding processes and power source
- A-5.06 Performs equipment start-up and shut-down
- A-5.07 Finishes final product
A-6 · Uses communications and mentoring techniques
0 official exam questions · 0 in the practice bank
- A-6.01 Uses communication techniques
- A-6.02 Uses mentoring techniques
BPerforms Layout and Fabrication of Components for Welding22%28168
B-7 · Performs layout
12 official exam questions · 62 in the practice bank
- B-7.01 Develops templates
- B-7.02 Transfers dimensions from drawings to materials
B-8 · Fabricates components
16 official exam questions · 106 in the practice bank
- B-8.01 Prepares materials
- B-8.02 Fits components for welding
- B-8.03 Assembles components
CPerforms Cutting and Gouging18%23138
C-9 · Uses tools and equipment for non-thermal cutting and grinding
6 official exam questions · 42 in the practice bank
- C-9.01 Selects cutting and grinding tools
- C-9.02 Cuts using stationary power tools
- C-9.03 Cuts using shears and ironworkers
- C-9.04 Cuts using hand tools
- C-9.05 Cuts using portable power tools
C-10 · Uses oxy-fuel gas cutting (OFC) process for cutting and gouging
7 official exam questions · 38 in the practice bank
- C-10.01 Selects OFC gas and equipment
- C-10.02 Sets up OFC equipment
- C-10.03 Sets operating parameters for OFC equipment
- C-10.04 Performs cut and gouge using OFC equipment
C-11 · Uses plasma arc cutting (PAC) process for cutting and gouging
6 official exam questions · 34 in the practice bank
- C-11.01 Selects PAC equipment and consumables
- C-11.02 Sets up PAC equipment
- C-11.03 Sets operating parameters for PAC equipment
- C-11.04 Performs cut and gouge using PAC equipment
C-12 · Uses air carbon arc cutting (CAC-A) process for cutting and gouging
4 official exam questions · 24 in the practice bank
- C-12.01 Selects CAC-A equipment and consumables
- C-12.02 Sets up CAC-A equipment
- C-12.03 Sets operating parameters for CAC-A equipment
- C-12.04 Performs cut and gouge using CAC-A equipment
DWelding Processes44%54324
D-13 · Welds using shielded metal arc welding (SMAW) process
18 official exam questions · 108 in the practice bank
- D-13.01 Selects SMAW equipment and consumables
- D-13.02 Sets up SMAW equipment
- D-13.03 Sets operating parameters for SMAW
- D-13.04 Performs weld using SMAW equipment
D-14 · Welds using flux cored arc welding (FCAW), metal cored arc welding (MCAW) and gas metal arc welding (GMAW) processes
18 official exam questions · 104 in the practice bank
- D-14.01 Selects FCAW, MCAW and GMAW gas, equipment and consumables
- D-14.02 Sets up FCAW, MCAW and GMAW equipment
- D-14.03 Sets operating parameters for FCAW, MCAW and GMAW
- D-14.04 Performs weld using FCAW, MCAW and GMAW equipment
D-15 · Welds using gas tungsten arc welding (GTAW) process
13 official exam questions · 78 in the practice bank
- D-15.01 Selects GTAW gas, equipment and consumables
- D-15.02 Sets up GTAW equipment
- D-15.03 Sets operating parameters for GTAW
- D-15.04 Performs weld using GTAW equipment
D-16 · Welds using submerged arc welding (SAW) process
5 official exam questions · 34 in the practice bank
- D-16.01 Selects SAW equipment and consumables
- D-16.02 Sets up SAW equipment
- D-16.03 Sets operating parameters for SAW
- D-16.04 Performs weld using SAW equipment
Source: the official Welder standard and exam breakdown. Check your own requirements with your province or territory.
Questions about Welder exam prep
Study guideIs there a free Welder Red Seal practice test?
Yes. Welder Exam 1 is a full practice exam of 125 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.
Is there a Welder practice test with answers?
Yes. Every Welder practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.
How many questions are on the Welder Red Seal exam?
The official Welder Red Seal exam has 125 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 88 of 125 questions correct.
What topics are on the Welder Red Seal exam?
The published exam breakdown has 4 Major Work Activities (MWAs) or blocks: A, Performs Common Occupational Skills (20 questions); B, Performs Layout and Fabrication of Components for Welding (28 questions); C, Performs Cutting and Gouging (23 questions); D, Welding Processes (54 questions).
Use the full trade breakdown to review the tasks in every MWA, and the official RSOS or NOA for the subtasks of each task.
Can I challenge the Welder Red Seal exam without an apprenticeship?
Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 125-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 6,000 in Ontario to 8,100 in Yukon (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.
How do your Welder practice exams follow the official breakdown?
Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.
What are Flashcard Match and Question Match?
Flashcard Match deals a board of Welder flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Welder practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.
How many Welder practice exams are included?
Pass Your Red Seal includes 6 practice exams and 750 original practice questions for Welder. Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 125 questions on the official exam.
Are Welder flashcards included?
Yes. Every Welder plan includes 250 flashcards in two exam-weighted sets of 125 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard - Welder (2023) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.
Can I try Welder practice questions for free?
Yes. Try 12 free Welder questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.
How much does Welder study access cost?
Study access for Welder costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.
Challenge the Welder exam without an apprenticeship
How it worksExperienced workers in the welder trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.
| Province or territory, with its guide | Hours to challenge | Apprenticeship and certification |
|---|---|---|
| British Columbia | 6,930 | Apprenticeship 5,400 hours · voluntary certification |
| Alberta | 7,020 | Apprenticeship 5,400 hours · compulsory certification |
| Saskatchewan | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Manitoba | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Ontario | 6,000 | Apprenticeship 6,000 hours · voluntary certification |
| Quebec | Quebec certificate first | Apprenticeship 1,800 hours · compulsory certification |
| New Brunswick | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Nova Scotia | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Prince Edward Island | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Newfoundland and Labrador | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Yukon | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Northwest Territories | 7,200 | Apprenticeship 5,400 hours · voluntary certification |
| Nunavut | 7,200 | Apprenticeship 5,400 hours · voluntary certification |
Source: Ellis Chart, Welder, published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.