Pass Your Red Seal
Exams

Online Red Seal Exam Preparation, built on official standards

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

Refrigeration and Air Conditioning Mechanic

Built on official standards for your trade

Practice exams split like the real exam.
Every answer explained.

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

4
Practice exams
500
Questions
250
Flashcards
1,000+
Flashcard Match
50+
Trade math
100+
Simulations
Try Refrigeration and Air Conditioning Mechanic free12 sample questions now, or Exam 1 with a free account12 sample questionsFree Exam 1

Practice exams

4 exams · 125 questions each

Exam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works

4 practice exams and 500 original practice questions with answers and explanations, plus 250 flashcards in two exam-weighted sets, for the 125-question Refrigeration and Air Conditioning Mechanic Red Seal exam. Timed or untimed, with pause and resume. 125 questions in the real exam · 4 hours · 70% pass mark.

Refrigeration and Air Conditioning Mechanic sample exam questions

Take them as an exam

12 free practice questions with answers and explanations. No account needed.

Sample 1 Refrigeration and Air Conditioning Mechanic, free sample

A portable gas monitor has a current calibration record. Before use, the specified test gas is applied until audible, visual and vibration alarms activate, then removed before a stable concentration reading is recorded. What has this check established?

Answer Sensor and alarm response has been demonstrated; numerical concentration accuracy remains a separate check.
Why This is a functional bump test: the applied gas causes the sensor and alarm system to respond. It does not establish concentration accuracy merely because the alarms operate. It also does not adjust the clean-air zero or the span response. Those are different procedures. The current calibration record and successful functional response are relevant checks with distinct purposes; the bump test cannot be represented as a new quantitative calibration.
2. A mechanic completes the manufacturer’s training on a new controller but needs prompts to restore its configuration backup on the training unit. The next service assignment requires that recovery skill. Which learning-plan revision best closes the demonstrated gap?
Answer Schedule supervised recovery practice, then verify an unprompted restore against the required checks.
Why The demonstrated gap is restoring the saved configuration independently. Targeted practice followed by an unprompted restore and verification directly addresses it. A successful guided restore still relies on the prompts that exposed the gap. Creating backups and checking file integrity are useful prerequisites, but neither demonstrates restoring the controller. Loading factory defaults can prove a different recovery operation; a controller can start normally while the required site configuration is missing. The skill check must match the planned service task.
3. A rooftop lift must finish within a crane permit window of 08:00-10:00. Delivery is booked for 09:00; receiving takes 15 minutes, rigging then takes 30 minutes, and lifting takes 30 minutes. These stages cannot overlap or be shortened. The crews and crane are available throughout the permit window, and an 08:45 delivery is available. Which single change makes completion possible?
Answer Move delivery to 08:45; retain the crane permit window.
Why The unavoidable chain after delivery is 15 + 30 + 30 = 75 minutes. A delivery at 08:45 finishes at 10:00 and fits the permit. Earlier rigger, crane or receiving-staff arrival cannot start work on equipment that has not arrived; with the 09:00 delivery, completion remains 10:15. This is a dependency problem, not a shortage of people on site. The chosen delivery change must be confirmed before the lift is scheduled.
4. A plan view shows two horizontal refrigerant lines crossing at grid D4. Section S2 through that crossing gives the upper line centreline elevation as 3.20 m and the lower line centreline as 3.05 m. Both lines measure 100 mm in outside diameter over the insulation. What clear vertical space exists between their insulation surfaces?
Answer 50 mm, taking both insulation radii from the section’s 150 mm vertical centreline separation.
Why The section establishes a 3.20 - 3.05 = 0.15 m, or 150 mm, vertical centreline separation. Each insulated line extends 50 mm toward the other, leaving 150 - 50 - 50 = 50 mm clear. Using 150 mm confuses centreline distance with surface clearance. Subtracting only one radius gives 100 mm and ignores the other line’s insulation. Adding a radius gives 200 mm, measuring away from rather than into the space between the lines.
5. A retrofit gateway must display a retained controller’s temperature and write its setpoint. The retained controller uses integer Modbus values in tenths of a degree Celsius; the new BACnet system uses degrees Celsius. The gateway supports separate read and write multipliers, with no offset. Which mapping preserves the intended temperature in both directions?
Answer Divide readings by 10; multiply outgoing setpoints by 10.
Why A Modbus value of 215 represents 21.5°C, so the read path multiplies the integer value by 0.1. A BACnet command of 21.5°C must become 215 at the retained controller, so the write path multiplies by 10. Reversing both factors mis-scales both directions. Using 0.1 both ways reads correctly but writes a value one hundredth of the required raw command. Using 10 both ways writes correctly but displays the read value one hundred times too high. Scaling must be checked separately in each direction.
6. A condensing-unit selection table gives these capacities at the required evaporating and outdoor design temperatures: unit K, 9.4 kW; L, 10.2 kW; M, 11.5 kW; N, 12.0 kW. All other requirements are met. The calculated load is 9.8 kW, and the design permits no more than 10% capacity oversizing. Which unit is within the permitted band?
Answer Unit L, whose design capacity covers the load within the permitted oversizing allowance.
Why The permitted band is 9.8 to 9.8 x 1.10 = 10.78 kW. Unit L at 10.2 kW lies within it. K at 9.4 kW is below the load even though it is close. M at 11.5 kW and N at 12.0 kW both exceed the specified oversizing limit; assumed future reserve or load growth do not override the design criterion. Use performance at the actual design temperatures rather than an unrelated nominal rating.
7. Before anchoring an air-handling unit, a site measurement gives 1,180 mm between its coil-access face and a column. The approved arrangement requires 1,250 mm of clear coil withdrawal space. The base can move along the same axis without changing orientation. What is the minimum layout correction?
Answer Move the equipment base 70 mm away from the column.
Why The withdrawal-space shortfall is 1,250 - 1,180 = 70 mm. Moving the base away from the column adds that clearance. Moving toward it subtracts clearance. Moving away by 140 mm would meet the requirement but is not the minimum correction; moving toward by 140 mm worsens the shortfall.
8. A horizontal evaporator suction line accepts an externally equalized thermostatic expansion valve. In the usual arrangement, where is its external equalizer connected relative to the sensing bulb?
Answer At the evaporator outlet, just downstream of the installed sensing bulb.
Why The usual connection is immediately downstream of the bulb at the evaporator outlet, where it reflects pressure at the bulb. An upstream outlet tap can be appropriate in an equipment manufacturer’s approved design, but it is not the general arrangement asked for. Either inlet tap senses pressure before the evaporator pressure drop and does not provide the intended outlet-pressure reference.
9. A heat pump’s secondary water-heating circuit requires 30 kPa gauge at its highest point when cold and static. That point is 14 m above the expansion-tank connection; the fill-pressure gauge is 2 m below the tank connection. Use 9.81 kPa pressure change per metre of water. The approved tank procedure sets precharge equal to cold-fill pressure at the tank connection, with the tank isolated and empty of water. Which tank precharge and subsequent fill-gauge reading meet the requirement, rounded to the nearest kPa?
Answer Set tank precharge to 167 kPa and fill-gauge pressure to 187 kPa.
Why Cold pressure at the tank connection must be 30 + 14 × 9.81 = 167.34 kPa gauge, so precharge is 167 kPa to the requested precision. The gauge is 2 m lower, where static water pressure is 19.62 kPa greater: 186.96 kPa, rounded to 187 kPa. Reversing the two settings puts the higher pressure at the higher point. Using 167 kPa at both locations ignores the lower gauge’s additional water head; using 187 kPa at both applies the gauge pressure to the tank without correcting for elevation. Precharge is set with the isolated tank empty, as specified.
10. A new heat pump is integrated with an existing zone-valve panel. Its approved sequence requires 30 s of continuously proven water flow and expiration of its minimum-off timer before compressor enable. The zone valve opens at 09:02:00, the pump starts then, and flow is proven at 09:02:20 without interruption. The minimum-off timer expires at 09:03:00. What is the earliest permitted compressor-enable time?
Answer At 09:03:00, when both independent start conditions have been met.
Why Flow has been continuously proven for 30 s at 09:02:50, but the minimum-off timer remains active until 09:03:00. Both conditions are first true at 09:03:00. Starting at 09:02:50 ignores the off timer. Waiting until 09:03:30 unnecessarily restarts an already completed independent flow interval. Starting at 09:02:30 measures from pump start rather than actual flow proof and also ignores the off timer.
11. An air handler delivers 3.0 m³/s instead of 4.0 m³/s. At 3.0 m³/s, its commissioning record shows drops of 45 Pa across the filter, 90 Pa across the coil and 35 Pa across the downstream damper section. Current measurements at the same taps are 48 Pa, 92 Pa and 140 Pa respectively. Motor speed matches the recorded setting; fan-wheel speed has not been measured. Which fault location is best supported?
Answer An increased restriction in the downstream damper section.
Why At the same measured airflow, the downstream section requires 140 Pa instead of 35 Pa, while the filter and coil drops remain close to their recorded values. This localizes the changed resistance to the downstream section. A slipping belt or reversed wheel can reduce delivered airflow, and motor speed alone does not exclude belt slip, but neither explains the increased pressure drop confined to that section at the same flow. The next inspection should identify the physical restriction without assuming the damper position from its command.
12. A refrigerant retrofit assessment checks lubricant miscibility separately from viscosity. What does the miscibility check establish?
Answer Whether oil and refrigerant form a uniform liquid mixture.
Why Miscibility describes the ability of liquid substances to mix without separating into distinct liquid phases under the relevant conditions. Film behaviour concerns viscosity and lubrication. Gas velocity affects entrainment and oil return, but does not define liquid miscibility. Discharge temperature influences operating conditions and oil properties; it does not by itself establish that oil and refrigerant remain mixed. Retrofit suitability requires checking these separate matters with the equipment and lubricant guidance.

Start free

Interactive simulations

Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.

Diagrams and symbols

Learn to read the diagrams and schematic symbols used in your trade.

How things work

Animated section drawings show what happens inside the equipment as it runs.

Terminology

Learn the correct name and job of every part.

Exam breakdown

Red Seal practice tests and exam prep

The official Refrigeration and Air Conditioning Mechanic Red Seal exam, also called the interprovincial (IP) exam, has 125 questions across 6 topic blocks. Open a block to see its tasks and subtasks.

125
Multiple choice questions
4 hours
Writing time
70%
Pass mark
Major Work Activity% of examReal examPractice bank
APerforms common occupational skills8%1040

A-1 · Maintains safe and healthy workplace

8 official exam questions · 32 in the practice bank

  • A-1.01 Maintains safe work environment
  • A-1.02 Performs lock-out, tag-out and isolation procedures
  • A-1.03 Uses personal protective equipment (PPE) and safety equipment
  • A-1.04 Participates in healthy and respectful work environment

A-2 · Maintains continuous learning

1 official exam question · 4 in the practice bank

  • A-2.01 Upskills in new trade practices and procedures
  • A-2.02 Upskills in emerging technologies

A-3 · Uses communication and mentoring techniques

1 official exam question · 4 in the practice bank

  • A-3.01 Uses communication techniques
  • A-3.02 Uses mentoring techniques
BPerforms routine trade activities16%2080

B-4 · Uses tools and equipment

5 official exam questions · 20 in the practice bank

  • B-4.01 Uses hand tools
  • B-4.02 Uses portable and stationary power tools
  • B-4.03 Uses piping and tubing connecting tools and equipment
  • B-4.04 Uses recovery, recycling and charging tools and equipment
  • B-4.05 Uses evacuation tools and equipment
  • B-4.06 Uses diagnostic and measuring tools and equipment
  • B-4.07 Uses electrical tools and equipment
  • B-4.08 Uses access equipment
  • B-4.09 Uses rigging, hoisting and lifting equipment
  • B-4.10 Uses digital technology

B-5 · Organizes work

4 official exam questions · 16 in the practice bank

  • B-5.01 Interprets drawings and specifications
  • B-5.02 Uses reference material and documentation
  • B-5.03 Plans job tasks and procedures

B-6 · Performs work site preparation

4 official exam questions · 16 in the practice bank

  • B-6.01 Prepares work site
  • B-6.02 Handles materials and supplies

B-7 · Performs trade-specific activities

7 official exam questions · 28 in the practice bank

  • B-7.01 Connects piping and tubing
  • B-7.02 Performs leak and pressure tests on systems
  • B-7.03 Evacuates systems
  • B-7.04 Uses refrigerants, gases and oils
  • B-7.05 Performs field wiring of systems
  • B-7.06 Applies sealants, adhesives and insulation
CPlans installation13%1664

C-8 · Plans installation of standard and high efficiency HVAC/R systems

6 official exam questions · 24 in the practice bank

  • C-8.01 Performs HVAC/R system design
  • C-8.02 Selects HVAC/R equipment, components and accessories
  • C-8.03 Determines placement of HVAC/R equipment, components and accessories
  • C-8.04 Performs HVAC/R material take-off

C-9 · Plans installation of control systems

4 official exam questions · 16 in the practice bank

  • C-9.01 Performs control system design
  • C-9.02 Selects control system components and accessories
  • C-9.03 Determines placement of control system components and accessories
  • C-9.04 Performs control system material take-off

C-10 · Plans retrofits

6 official exam questions · 24 in the practice bank

  • C-10.01 Analyzes energy efficiency of current system
  • C-10.02 Determines requirements for retrofits
  • C-10.03 Analyzes distribution requirements for retrofits
  • C-10.04 Performs design and sizing of retrofit equipment and components
  • C-10.05 Plans retrofit of control systems
DPerforms installation21%26104

D-11 · Installs HVAC/R systems

16 official exam questions · 64 in the practice bank

  • D-11.01 Confirms system layout
  • D-11.02 Assembles HVAC/R equipment, components and accessories
  • D-11.03 Places HVAC/R equipment, components and accessories
  • D-11.04 Retrofits HVAC/R equipment refrigerants and refrigerant oils
  • D-11.05 Retrofits HVAC/R equipment, components and accessories
  • D-11.06 Installs fasteners, brackets and hangers
  • D-11.07 Installs HVAC/R piping and tubing
  • D-11.08 Applies HVAC/R holding charge

D-12 · Installs control systems

10 official exam questions · 40 in the practice bank

  • D-12.01 Places control system components
  • D-12.02 Connects control systems
  • D-12.03 Retrofits control systems
EPerforms commissioning17%2288

E-13 · Commissions new and retrofitted HVAC/R and control system components

12 official exam questions · 48 in the practice bank

  • E-13.01 Performs pre-start -up checks for HVAC/R systems
  • E-13.02 Performs start-up of HVAC/R systems
  • E-13.03 Performs start-up checks for control systems
  • E-13.04 Completes HVAC/R system charge
  • E-13.05 Sets up primary and secondary HVAC/R system components

E-14 · Verifies system performance

10 official exam questions · 40 in the practice bank

  • E-14.01 Verifies/sets operating parameters
  • E-14.02 Verifies system integration
  • E-14.03 Performs system optimization
  • E-14.04 Completes commissioning documentation
FPerforms maintenance and service25%31124

F-15 · Maintains HVAC/R systems

9 official exam questions · 36 in the practice bank

  • F-15.01 Inspects HVAC/R systems
  • F-15.02 Performs predictive and scheduled maintenance on HVAC/R systems
  • F-15.03 Tests HVAC/R system components and accessories
  • F-15.04 Optimizes integrated system performance

F-16 · Services HVAC/R systems

13 official exam questions · 52 in the practice bank

  • F-16.01 Troubleshoots HVAC/R systems
  • F-16.02 Repairs HVAC/R systems

F-17 · Maintains and services control systems

9 official exam questions · 36 in the practice bank

  • F-17.01 Performs maintenance and inspection on control systems
  • F-17.02 Troubleshoots control systems
  • F-17.03 Calibrates operating and safety controls
  • F-17.04 Repairs control systems

Source: the official Refrigeration and Air Conditioning Mechanic standard and exam breakdown. Check your own requirements with your province or territory.

Questions about Refrigeration and Air Conditioning Mechanic exam prep

Study guide
Is there a free Refrigeration and Air Conditioning Mechanic Red Seal practice test?

Yes. Refrigeration and Air Conditioning Mechanic Exam 1 is a full practice exam of 125 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.

Is there a Refrigeration and Air Conditioning Mechanic practice test with answers?

Yes. Every Refrigeration and Air Conditioning Mechanic practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.

How many questions are on the Refrigeration and Air Conditioning Mechanic Red Seal exam?

The official Refrigeration and Air Conditioning Mechanic Red Seal exam has 125 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 88 of 125 questions correct.

What topics are on the Refrigeration and Air Conditioning Mechanic Red Seal exam?

The published exam breakdown has 6 Major Work Activities (MWAs) or blocks: A, Performs common occupational skills (10 questions); B, Performs routine trade activities (20 questions); C, Plans installation (16 questions); D, Performs installation (26 questions); E, Performs commissioning (22 questions); F, Performs maintenance and service (31 questions).

Can I challenge the Refrigeration and Air Conditioning Mechanic Red Seal exam without an apprenticeship?

Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 125-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 9,000 in Ontario to 10,800 in Yukon (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.

How do your Refrigeration and Air Conditioning Mechanic practice exams follow the official breakdown?

Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.

What are Flashcard Match and Question Match?

Flashcard Match deals a board of Refrigeration and Air Conditioning Mechanic flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Refrigeration and Air Conditioning Mechanic practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.

How many Refrigeration and Air Conditioning Mechanic practice exams are included?

Pass Your Red Seal includes 4 practice exams and 500 original practice questions for Refrigeration and Air Conditioning Mechanic. Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 125 questions on the official exam.

Are Refrigeration and Air Conditioning Mechanic flashcards included?

Yes. Every Refrigeration and Air Conditioning Mechanic plan includes 250 flashcards in two exam-weighted sets of 125 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard - Refrigeration and Air Conditioning Mechanic (2024) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.

Can I try Refrigeration and Air Conditioning Mechanic practice questions for free?

Yes. Try 12 free Refrigeration and Air Conditioning Mechanic questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.

How much does Refrigeration and Air Conditioning Mechanic study access cost?

Study access for Refrigeration and Air Conditioning Mechanic costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.

Challenge the Refrigeration and Air Conditioning Mechanic exam without an apprenticeship

How it works

Experienced workers in the refrigeration and air conditioning mechanic trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.

Experience required to challenge the Refrigeration and Air Conditioning Mechanic Red Seal exam
Province or territory, with its guideHours to challengeApprenticeship and certification
British Columbia9,315Apprenticeship 7,200 hours · compulsory certification
Alberta9,360Apprenticeship 7,200 hours · compulsory certification
Saskatchewan10,800Apprenticeship 7,200 hours · compulsory certification
Manitoba10,800Apprenticeship 7,200 hours · compulsory certification
Ontario
Refrigeration and Air Conditioning Systems Mechanic
9,000Apprenticeship 9,000 hours · compulsory certification
Quebec
Refrigeration Specialist; Class 1 refrigeration systems (non-construction)
Quebec certificate firstApprenticeship 8,000 hours · compulsory certification
New Brunswick
Refrigeration and Air Conditioning Technician
10,800Apprenticeship 7,200 hours · compulsory certification
Nova Scotia10,800Apprenticeship 7,200 hours · compulsory certification
Prince Edward Island10,800Apprenticeship 7,200 hours · voluntary certification
Newfoundland and Labrador10,800Apprenticeship 7,200 hours · voluntary certification
Yukon10,800Apprenticeship 7,200 hours · voluntary certification
Northwest Territories9,000Apprenticeship 7,200 hours · voluntary certification
Nunavut9,000Apprenticeship 7,200 hours · voluntary certification

Source: Ellis Chart, Refrigeration and Air Conditioning Mechanic, published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.