Pass Your Red Seal
Exams

Online Red Seal Exam Preparation, built on official standards

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

Heavy Duty Equipment Technician

Built on official standards for your trade

Practice exams split like the real exam.
Every answer explained.

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

6
Practice exams
810
Questions
270
Flashcards
1,000+
Flashcard Match
50+
Trade math
100+
Simulations
Try Heavy Duty Equipment Technician free12 sample questions now, or Exam 1 with a free account12 sample questionsFree Exam 1

Practice exams

6 exams · 135 questions each

Exam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works

6 practice exams and 810 original practice questions with answers and explanations, plus 270 flashcards in two exam-weighted sets, for the 135-question Heavy Duty Equipment Technician Red Seal exam. Timed or untimed, with pause and resume. 135 questions in the real exam · 4 hours · 70% pass mark.

Heavy Duty Equipment Technician sample exam questions

Take them as an exam

12 free practice questions with answers and explanations. No account needed.

Sample 1 Heavy Duty Equipment Technician, free sample

A bushing tips during a press trial. With force released and the assembly safely supported, inspection finds the driver face tilted and its axis offset from the bore. Support deflection remains within the setup limit. Which correction addresses the measured setup defect?

Answer Square and centre the driver with the bore before another controlled trial
Why The driver should apply the specified force along the bore axis with the correct contact face. Measured tilt and offset create an eccentric load, so correct them before the next controlled trial. Reducing a support span that already passes its deflection check does not align the driver; added force or lubricant also leaves the measured eccentricity. Other support or interference defects can cause tipping, but this stem supplies the actual setup findings.
2. An engine oil-pump repair has corrected its regulating-valve defect. The reuse procedure also requires gear-tip and end clearances to be measured. Why do those checks remain necessary?
Answer Excess internal clearance can lower effective delivery despite a sound regulator
Why Excess internal clearances permit leakage from high- to low-pressure regions, reducing effective delivery under operating conditions. A sound regulator does not repair that leakage or establish either required clearance. Claiming increased flow reverses the leakage effect. Final pressure depends on pump delivery and system resistance, so a regulator repair alone is not proof of restored engine lubrication.
3. The selected sealed track-chain repair procedure requires its specified press tooling, replacement seals and measured pin position. A replacement link section is approved for this chain. Which reassembly plan preserves the joint requirements?
Answer Select the prescribed press tooling, fit new seals and verify the pin position
Why The tooling, new seals and final pin position are all specified. Reusing seals violates the replacement requirement even if pin position is correct. Omitting the position check leaves the assembly geometry unverified, and reusing seals as well omits both controls. Master-joint designs and required replacement parts vary; this item does not prescribe a universal new master link or hammer/weld repair.
4. A starter test requires voltage actually delivered across the starter motor while cranking under the approved no-start procedure. Which lead locations measure that value?
Answer Measure between starter B+ and the starter case while the engine cranks
Why Across starter B+ and its case measures the voltage at the motor input and return. Battery-post to battery-post measures battery terminal voltage. Starter B+ to battery negative includes the starter and return-path drop; battery positive to case includes the positive-feed drop as well as starter voltage. Those are not simply positive-side or ground-side drop tests. To measure a cable drop, place leads across that cable path under load.
5. A powershift clutch procedure specifies new lip seals facing apply pressure and a clean, freely operating centrifugal bleed check. Which assembly satisfies those conditions?
Answer Face new lips toward apply pressure and verify the bleed check moves freely
Why The prescribed orientation lets pressure energize the lips, while the specified bleed-check operation controls retained rotating oil as designed. Reversed lips violate orientation. A stuck check leaves the required bleed function unverified, even with correct seals; the final combination fails both. Follow the actual clutch design, including air/pressure checks and all clearances, rather than inferring the prior burn cause from assembly features alone.
6. A dump truck has increased exhaust noise. Inspection under its service procedure finds a detached muffler baffle; exhaust piping is intact and cab mount checks pass. What finding should the repair address first?
Answer The detached muffler baffle and its lost acoustic-control function
Why The detached baffle is an observed muffler defect and can change attenuation and resonance. It does not by itself prove complete blockage. The other alternatives contradict the checked mounts or piping and do not address the identified internal defect. Noise and backpressure alone may not localize a muffler failure; the inspection supplies the decisive evidence.
7. A swing circuit accelerates slowly. Under the approved test, pressure rises promptly before its acceleration metering valve but slowly after it; the valve command is correct and the motor case-drain result is within limits. What should be investigated first?
Answer A restriction through the commanded acceleration metering path
Why The delayed rise is localized across the commanded metering path. A restriction upstream does not fit prompt upstream response. The accepted case-drain and command checks make their corresponding alternatives less supported by this test. Confirm the valve/orifice condition using the circuit procedure; normal operation of other functions alone would not prove the main pump responds correctly to every swing demand.
8. A propel-loop parts diagram specifies relief cartridge F at 28 MPa and R at 24 MPa. Both physically fit either port. What assembly check prevents reversal of the specified directional ratings?
Answer Match 28 MPa to port F and 24 MPa to port R using the diagram
Why The diagram assigns a different calibrated cartridge to each port. Reversing them interchanges the directional limits. Using either rating in both ports removes the intended distinction. Mechanical interchangeability establishes fit, not the required function; verify final operation under the manufacturer test procedure after correct installation.
9. A compressor coalescing pre-filter is heavily oil-fouled at service. The system procedure requires investigating abnormal oil loading. What follow-up protects the replacement element and dryer?
Answer Record the contaminant loading and investigate the upstream oil source
Why The filter condition is evidence to investigate the oil source and operating conditions. Replacing the element removes collected contamination but does not establish that the cause is corrected. Changing governor pressure or purge time without diagnosis alters other system controls and does not identify the source. Heavy loading alone does not condemn the reservoir or prove a particular compressor part has failed.
10. An equalizer-bar service detail specifies 0.8 to 1.2 mm saddle running clearance. The measured gap is 1.8 mm, and the approved shim arrangement reduces that gap by the added shim thickness. Which added shim reaches the middle of the range?
Answer Add 0.8 mm of shim thickness, leaving a running clearance of 1.0 mm
Why The midpoint is(0.8+1.2)/2=1.0 mm. Reducing 1.8 to 1.0 requires 0.8 mm of added shim under the specified geometry. The 0.6 and 1.0 mm choices land on range boundaries rather than its midpoint; 1.8 mm removes the required running clearance. The item supplies the exact shim effect instead of assuming every equalizer-bar design adjusts the same way.
11. The cab service sheet identifies separate fresh-air and recirculation filters as non-cleanable replacement elements. Both are due. Which service and verification satisfy that instruction?
Answer Replace both specified filters, check their seals and verify defrost airflow
Why Both elements are specified for replacement, with seating/seal and airflow checks completing that service. Replacing only either one leaves the other scheduled element unchanged. Cleaning elements explicitly marked non-cleanable does not meet the sheet. Restored airflow must be observed; filter service alone does not prove all causes of fogging or defrost weakness have been eliminated.
12. A high-voltage isolation fault appears after rain and disappears when dry. An approved de-energized segmented test reproduces low insulation resistance in one harness branch; isolated battery, inverter and motor sections pass. What does this establish?
Answer The tested harness branch needs moisture-entry and insulation investigation
Why The reproduced segmented failure locates the present insulation concern to that harness branch. Passing while dry does not negate a condition-dependent fault. Condemning the separately passing inverter or battery contradicts these isolation results. Follow the approved diagnostic and energy-control procedure to find the entry or insulation damage; do not improvise a wet high-voltage test or infer external connectors solely because dry components passed.

Start free

Interactive simulations

Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.

Diagrams and symbols

Learn to read the diagrams and schematic symbols used in your trade.

How things work

Animated section drawings show what happens inside the equipment as it runs.

Terminology

Learn the correct name and job of every part.

Exam breakdown

Red Seal practice tests and exam prep

The official Heavy Duty Equipment Technician Red Seal exam, also called the interprovincial (IP) exam, has 135 questions across 9 topic blocks. Open a block to see its tasks and subtasks.

135
Multiple choice questions
4 hours
Writing time
70%
Pass mark
Major Work Activity% of examReal examPractice bank
APerforms common occupational skills7%1060

A-1 · Performs safety-related functions

3 official exam questions · 12 in the practice bank

  • A-1.01 Performs hazard analysis
  • A-1.02 Maintains safe work environment
  • A-1.03 Uses personal protective equipment (PPE) and safety equipment
  • A-1.04 Implements safety protocols for hybrid and all-electric equipment and attachments

A-2 · Uses and maintains tools and equipment

4 official exam questions · 21 in the practice bank

  • A-2.01 Uses hand, power, measuring, testing and diagnostic tools
  • A-2.02 Uses shop equipment
  • A-2.03 Uses access equipment
  • A-2.04 Uses hoisting, rigging, lifting, cribbing and blocking equipment
  • A-2.05 Uses welding equipment
  • A-2.06 Uses heating and cutting equipment
  • A-2.07 Uses electronic service tools and systems for diagnostics and programming

A-3 · Performs routine work practices

3 official exam questions · 24 in the practice bank

  • A-3.01 Uses documentation and reference materials
  • A-3.02 Prepares job action plan
  • A-3.03 Maintains fluids and lubricants
  • A-3.04 Services hoses, tubing, piping and fittings
  • A-3.05 Services bearings and seals
  • A-3.06 Uses fasteners and sealing materials
  • A-3.07 Services safety features
  • A-3.08 Performs operational check-out

A-4 · Uses communication and mentoring techniques

0 official exam questions · 3 in the practice bank

  • A-4.01 Uses communication techniques
  • A-4.02 Uses mentoring techniques
BServices, diagnoses and repairs engines and supporting systems15%20120

B-5 · Services, diagnoses and repairs base engines

3 official exam questions · 18 in the practice bank

  • B-5.01 Services base engines
  • B-5.02 Diagnoses base engines
  • B-5.03 Repairs base engines

B-6 · Services, diagnoses and repairs lubrication systems

2 official exam questions · 12 in the practice bank

  • B-6.01 Services lubrication systems
  • B-6.02 Diagnoses lubrication systems
  • B-6.03 Repairs lubrication systems

B-7 · Services, diagnoses and repairs intake systems

2 official exam questions · 12 in the practice bank

  • B-7.01 Services intake systems
  • B-7.02 Diagnoses intake systems
  • B-7.03 Repairs intake systems

B-8 · Services, diagnoses and repairs exhaust systems

2 official exam questions · 12 in the practice bank

  • B-8.01 Services exhaust systems
  • B-8.02 Diagnoses exhaust systems
  • B-8.03 Repairs exhaust systems

B-9 · Services, diagnoses and repairs engine management systems

3 official exam questions · 18 in the practice bank

  • B-9.01 Services engine management systems
  • B-9.02 Diagnoses engine management systems
  • B-9.03 Repairs engine management systems

B-10 · Services, diagnoses and repairs fuel delivery systems

3 official exam questions · 18 in the practice bank

  • B-10.01 Services fuel delivery systems
  • B-10.02 Diagnoses fuel delivery systems
  • B-10.03 Repairs fuel delivery systems

B-11 · Services, diagnoses and repairs emission control systems

3 official exam questions · 18 in the practice bank

  • B-11.01 Services emission control systems
  • B-11.02 Diagnoses emission control systems
  • B-11.03 Repairs emission control systems

B-12 · Services, diagnoses and repairs cooling systems

2 official exam questions · 12 in the practice bank

  • B-12.01 Services cooling systems
  • B-12.02 Diagnoses cooling systems
  • B-12.03 Repairs cooling systems
CServices, diagnoses and repairs steering, suspension, brake and undercarriage systems, and wheel assemblies12%1696

C-13 · Services, diagnoses and repairs steering systems

4 official exam questions · 24 in the practice bank

  • C-13.01 Services steering systems
  • C-13.02 Diagnoses steering systems
  • C-13.03 Repairs steering systems

C-14 · Services, diagnoses and repairs suspension systems

3 official exam questions · 18 in the practice bank

  • C-14.01 Services suspension systems
  • C-14.02 Diagnoses suspension systems
  • C-14.03 Repairs suspension systems

C-15 · Services, diagnoses and repairs brake systems

4 official exam questions · 21 in the practice bank

  • C-15.01 Services brake systems
  • C-15.02 Diagnoses brake systems
  • C-15.03 Repairs brake systems

C-16 · Services, diagnoses and repairs undercarriage systems

3 official exam questions · 18 in the practice bank

  • C-16.01 Services undercarriage systems
  • C-16.02 Diagnoses undercarriage systems
  • C-16.03 Repairs undercarriage systems

C-17 · Services, diagnoses and repairs wheel assemblies

2 official exam questions · 15 in the practice bank

  • C-17.01 Services wheel assemblies
  • C-17.02 Diagnoses wheel assemblies
  • C-17.03 Repairs wheel assemblies
DServices, diagnoses and repairs electrical and electronic systems19%25150

D-18 · Service, diagnoses and repairs charging systems

5 official exam questions · 30 in the practice bank

  • D-18.01 Services charging systems
  • D-18.02 Diagnoses charging systems
  • D-18.03 Repairs charging systems

D-19 · Service, diagnoses and repairs starting systems

4 official exam questions · 27 in the practice bank

  • D-19.01 Services starting systems
  • D-19.02 Diagnoses starting systems
  • D-19.03 Repairs starting systems

D-20 · Service, diagnoses and repairs battery systems

4 official exam questions · 27 in the practice bank

  • D-20.01 Services battery systems
  • D-20.02 Diagnoses battery systems
  • D-20.03 Repairs battery systems

D-21 · Services, diagnoses and repairs electrical components

6 official exam questions · 33 in the practice bank

  • D-21.01 Services electrical components
  • D-21.02 Diagnoses electrical components
  • D-21.03 Repairs electrical components

D-22 · Services, diagnoses and repairs equipment management systems and electronic components

6 official exam questions · 33 in the practice bank

  • D-22.01 Services equipment management systems and electronic components
  • D-22.02 Diagnoses equipment management systems and electronic components
  • D-22.03 Repairs equipment management systems and electronic components
EServices, diagnoses and repairs drivetrain systems13%17102

E-23 · Services, diagnoses and repairs clutches

1 official exam question · 9 in the practice bank

  • E-23.01 Services clutches
  • E-23.02 Diagnoses clutches
  • E-23.03 Repairs clutches

E-24 · Services, diagnoses and repairs torque converters, fluid couplers and hydraulic retarders

2 official exam questions · 12 in the practice bank

  • E-24.01 Services torque converters, fluid couplers and hydraulic retarders
  • E-24.02 Diagnoses torque converters, fluid couplers and hydraulic retarders
  • E-24.03 Repairs torque converters, fluid couplers and hydraulic retarders

E-25 · Services, diagnoses and repairs manual transmissions and transfer cases

2 official exam questions · 12 in the practice bank

  • E-25.01 Services manual transmissions and transfer cases
  • E-25.02 Diagnoses manual transmissions and transfer cases
  • E-25.03 Repairs manual transmissions and transfer cases

E-26 · Services, diagnoses and repairs automatic and powershift transmissions

4 official exam questions · 21 in the practice bank

  • E-26.01 Services automatic and powershift transmissions
  • E-26.02 Diagnoses automatic and powershift transmissions
  • E-26.03 Repairs automatic and powershift transmissions

E-27 · Services, diagnoses and repairs driveline systems

2 official exam questions · 12 in the practice bank

  • E-27.01 Services driveline systems
  • E-27.02 Diagnoses driveline systems
  • E-27.03 Repairs driveline systems

E-28 · Services, diagnoses and repairs drive axles and differentials

3 official exam questions · 18 in the practice bank

  • E-28.01 Services drive axles and differentials
  • E-28.02 Diagnoses drive axles and differentials
  • E-28.03 Repairs drive axles and differentials

E-29 · Services, diagnoses and repairs final drive systems

3 official exam questions · 18 in the practice bank

  • E-29.01 Services final drive systems
  • E-29.02 Diagnoses final drive systems
  • E-29.03 Repairs final drive systems
FServices, diagnoses and repairs environmental control systems6%954

F-30 · Services, diagnoses and repairs heating systems

3 official exam questions · 18 in the practice bank

  • F-30.01 Services heating systems
  • F-30.02 Diagnoses heating systems
  • F-30.03 Repairs heating systems

F-31 · Services, diagnoses and repairs ventilation and filtration systems

2 official exam questions · 12 in the practice bank

  • F-31.01 Services ventilation and filtration systems
  • F-31.02 Diagnoses ventilation and filtration systems
  • F-31.03 Repairs ventilation and filtration systems

F-32 · Services, diagnoses and repairs air conditioning systems

3 official exam questions · 15 in the practice bank

  • F-32.01 Services air conditioning systems
  • F-32.02 Diagnoses air conditioning systems
  • F-32.03 Repairs air conditioning systems

F-33 · Services, diagnoses and repairs sound suppression systems

1 official exam question · 9 in the practice bank

  • F-33.01 Services sound suppression systems
  • F-33.02 Diagnoses sound suppression systems
  • F-33.03 Repairs sound suppression systems
GServices, diagnoses and repairs hydraulic, hydrostatic and pneumatic systems19%25150

G-34 · Services, diagnoses and repairs hydraulic systems

11 official exam questions · 63 in the practice bank

  • G-34.01 Services hydraulic systems
  • G-34.02 Diagnoses hydraulic systems
  • G-34.03 Repairs hydraulic systems

G-35 · Services, diagnoses and repairs hydrostatic systems

9 official exam questions · 54 in the practice bank

  • G-35.01 Services hydrostatic systems
  • G-35.02 Diagnoses hydrostatic systems
  • G-35.03 Repairs hydrostatic systems

G-36 · Services, diagnoses and repairs pneumatic systems

5 official exam questions · 33 in the practice bank

  • G-36.01 Services pneumatic systems
  • G-36.02 Diagnoses pneumatic systems
  • G-36.03 Repairs pneumatic systems
HServices, diagnoses and repairs structural components, operator stations, attachments and accessories7%954

H-37 · Services, diagnoses and repairs structural components

3 official exam questions · 18 in the practice bank

  • H-37.01 Services structural components
  • H-37.02 Diagnoses structural components
  • H-37.03 Performs mechanical repairs on structural components

H-38 · Services, diagnoses and repairs operator station components

3 official exam questions · 16 in the practice bank

  • H-38.01 Services operator station components
  • H-38.02 Diagnoses operator station components
  • H-38.03 Repairs operator station components

H-39 · Services, diagnoses and repairs attachments and accessories

3 official exam questions · 20 in the practice bank

  • H-39.01 Services attachments and accessories
  • H-39.02 Diagnoses attachments and accessories
  • H-39.03 Repairs attachments and accessories
  • H-39.04 Installs attachments and accessories
IServices, diagnoses and repairs hybrid and all-electric equipment2%424

I-40 · Services, diagnoses and repairs hybrid equipment

2 official exam questions · 12 in the practice bank

  • I-40.01 Services hybrid equipment
  • I-40.02 Diagnoses hybrid equipment
  • I-40.03 Repairs hybrid equipment

I-41 · Services, diagnoses and repairs all-electric equipment

2 official exam questions · 12 in the practice bank

  • I-41.01 Services all-electric equipment
  • I-41.02 Diagnoses all-electric equipment
  • I-41.03 Repairs all-electric equipment

Source: the official Heavy Duty Equipment Technician standard and exam breakdown. Check your own requirements with your province or territory.

Questions about Heavy Duty Equipment Technician exam prep

Study guide
Is there a free Heavy Duty Equipment Technician Red Seal practice test?

Yes. Heavy Duty Equipment Technician Exam 1 is a full practice exam of 135 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.

Is there a Heavy Duty Equipment Technician practice test with answers?

Yes. Every Heavy Duty Equipment Technician practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.

How many questions are on the Heavy Duty Equipment Technician Red Seal exam?

The official Heavy Duty Equipment Technician Red Seal exam has 135 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 95 of 135 questions correct.

What topics are on the Heavy Duty Equipment Technician Red Seal exam?

The published exam breakdown has 9 Major Work Activities (MWAs) or blocks: A, Performs common occupational skills (10 questions); B, Services, diagnoses and repairs engines and supporting systems (20 questions); C, Services, diagnoses and repairs steering, suspension, brake and undercarriage systems, and wheel assemblies (16 questions); D, Services, diagnoses and repairs electrical and electronic systems (25 questions); E, Services, diagnoses and repairs drivetrain systems (17 questions); F, Services, diagnoses and repairs environmental control systems (9 questions); G, Services, diagnoses and repairs hydraulic, hydrostatic and pneumatic systems (25 questions); H, Services, diagnoses and repairs structural components, operator stations, attachments and accessories (9 questions); I, Services, diagnoses and repairs hybrid and all-electric equipment (4 questions).

Can I challenge the Heavy Duty Equipment Technician Red Seal exam without an apprenticeship?

Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 135-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 6,750 in Alberta to 10,800 in Newfoundland and Labrador (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.

How do your Heavy Duty Equipment Technician practice exams follow the official breakdown?

Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.

What are Flashcard Match and Question Match?

Flashcard Match deals a board of Heavy Duty Equipment Technician flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Heavy Duty Equipment Technician practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.

How many Heavy Duty Equipment Technician practice exams are included?

Pass Your Red Seal includes 6 practice exams and 810 original practice questions for Heavy Duty Equipment Technician. Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 135 questions on the official exam.

Are Heavy Duty Equipment Technician flashcards included?

Yes. Every Heavy Duty Equipment Technician plan includes 270 flashcards in two exam-weighted sets of 135 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard - Heavy Duty Equipment Technician (2023) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.

Can I try Heavy Duty Equipment Technician practice questions for free?

Yes. Try 12 free Heavy Duty Equipment Technician questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.

How much does Heavy Duty Equipment Technician study access cost?

Study access for Heavy Duty Equipment Technician costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.

Challenge the Heavy Duty Equipment Technician exam without an apprenticeship

How it works

Experienced workers in the heavy duty equipment technician trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.

Experience required to challenge the Heavy Duty Equipment Technician Red Seal exam
Province or territory, with its guideHours to challengeApprenticeship and certification
British Columbia9,495Apprenticeship 7,200 hours · voluntary certification
Alberta
Heavy Equipment Technician - Heavy Duty Equipment Mechanic (Off Road)
6,750Apprenticeship 5,220 hours · compulsory certification
Saskatchewan10,800Apprenticeship 7,200 hours · voluntary certification
Manitoba10,800Apprenticeship 7,200 hours · voluntary certification
Ontario7,000Apprenticeship 7,000 hours · voluntary certification
Quebec
Heavy Equipment Mechanic; Mechanic, heavy duty equipment
Quebec certificate firstApprenticeship 6,000 hours · compulsory certification
New Brunswick10,800Apprenticeship 7,200 hours · voluntary certification
Nova Scotia10,800Apprenticeship 7,200 hours · voluntary certification
Prince Edward Island10,800Apprenticeship 7,200 hours · voluntary certification
Newfoundland and Labrador10,800Apprenticeship 7,200 hours · voluntary certification
Yukon
Heavy Duty Equipment Technician (Off Road)
8,100Apprenticeship 5,400 hours · voluntary certification
Northwest Territories
Heavy Duty Equipment Technician; Heavy Equipment Technician - Heavy Duty Equipment Mechanic (Off Road)
9,000Apprenticeship 7,200 hours · voluntary certification
Nunavut
Heavy Equipment Technician - Off Road Mechanic
7,200Apprenticeship 5,400 hours · voluntary certification

Source: Ellis Chart, Heavy Duty Equipment Technician, published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.