Online Red Seal Exam Preparation, built on official standards
Roofer
Built on official standards for your trade
Practice exams split like the real exam.
Every answer explained.
- 4
- Practice exams
- 500
- Questions
- 250
- Flashcards
- 1,000+
- Flashcard Match
- 50+
- Trade math
- 100+
- Simulations
Practice exams
4 exams · 125 questions eachExam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works
4 practice exams and 500 original practice questions with answers and explanations, plus 250 flashcards in two exam-weighted sets, for the 125-question Roofer Red Seal exam. Timed or untimed, with pause and resume. 125 questions in the real exam · 4 hours · 70% pass mark.
Roofer sample exam questions
Take them as an exam12 free practice questions with answers and explanations. No account needed.
An access-ladder plan specifies a 4:1 rise-to-base ratio for a 5 m rise, secured supports and the required landing extension. What base distance satisfies the ratio?
2. A roofer is estimating cap sheet for a flat roof field of 540 m². The SBS cap sheet is sold in rolls that cover 8 m² net after the side and end laps are deducted. The estimate must include a 12% allowance for waste, flashings, and cut-in. How many full rolls should be ordered?
3. A shingle estimate uses a net field area of exactly 2000 ft². One square is 100 ft² and the selected product uses three bundles per square. The estimating sheet adds 10% for its listed extras. How many complete bundles are required?
4. A reroofing detail shows embedded through-wall flashing above the base flashing. Its condition and connection to the replacement roof are not yet verified. What must be resolved before the new base flashing conceals the interface?
5. An installed rooftop curb obstructs the designed drainage path. No upstream diversion detail appears in the issued roof drawings. What should the roofer do before completing this area?
6. An adhered roof assembly lists only cover board G, at 12.7 mm, with attachment schedule S. An otherwise similar wood-fibre board W has no approval for this assembly. Which submittal can be accepted against the issued requirements?
7. A project base-flashing detail requires a 200 mm minimum rise above the finished roof, mechanical top securement and counterflashing. Which installation satisfies all three features?
8. A chimney cricket detail shows upslope shingles discharging onto the cricket and counterflashing covering the cricket’s wall upstand. Which lap arrangement follows those two water-shedding interfaces?
9. A roof-tile detail gives an overall tile length of 360 mm and requires a 75 mm headlap. It defines field-course batten gauge as overall length minus headlap. Ignoring the special eave course, what gauge results?
10. A foundation drainage-sheet detail for the selected product requires dimples toward the wall and a sealed termination strip above final grade. Which installation follows this product detail?
11. A PVC roof-drain repair detail requires removal of the strained membrane, a compatible target patch welded to sound membrane, fresh specified sealant and a correctly tightened clamping ring. Which repair meets the complete detail?
12. A closed-cut valley’s product detail specifies a 50 mm cut-line offset and compatible cement beneath the cut edges. Inspection finds a centreline cut and missing cement. Which correction follows this detail, assuming the affected shingles can be repaired as specified?
Start free
Interactive simulations
Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.
Learn to read the diagrams and schematic symbols used in your trade.
Animated section drawings show what happens inside the equipment as it runs.
Learn the correct name and job of every part.
Exam breakdown
Red Seal practice tests and exam prepThe official Roofer Red Seal exam, also called the interprovincial (IP) exam, has 125 questions across 6 topic blocks. Open a block to see its tasks and subtasks.
- 125
- Multiple choice questions
- 4 hours
- Writing time
- 70%
- Pass mark
APerforms common occupational skills18%2392
A-1 · Performs safety related functions
7 official exam questions · 12 in the practice bank
- A-1.01 Maintains safe work environment
- A-1.02 Uses personal protective equipment (PPE) and safety equipment
A-2 · Uses tools and equipment
7 official exam questions · 36 in the practice bank
- A-2.01 Uses hand tools
- A-2.02 Uses power tools, pneumatic tools, and hot-air welding, induction and fuelled equipment
- A-2.03 Uses hoisting, lifting and rigging equipment
- A-2.04 Uses access equipment
- A-2.05 Uses hot process equipment
- A-2.06 Uses motorized equipment
A-3 · Organizes work
6 official exam questions · 36 in the practice bank
- A-3.01 Uses documentation and reference materials
- A-3.02 Interprets blueprints and drawings
- A-3.03 Estimates material
- A-3.04 Assesses worksite conditions
- A-3.05 Positions equipment and material on the ground and on the roof
- A-3.06 Prepares material disposal systems
- A-3.07 Evaluates roof conditions near rooftop equipment installations
A-4 · Uses communication and mentoring techniques
3 official exam questions · 8 in the practice bank
- A-4.01 Uses communication techniques
- A-4.02 Uses mentoring techniques
BPrepares roof and deck14%1872
B-5 · Prepares roof for replacement
10 official exam questions · 44 in the practice bank
- B-5.01 Protects surrounding area
- B-5.02 Removes loose debris
- B-5.03 Removes roofing and flashings
- B-5.04 Prepares roof substrate
- B-5.05 Performs minor adjustments to penetrations, curbs and parapets
B-6 · Prepares deck for roof installation
8 official exam questions · 28 in the practice bank
- B-6.01 Inspects deck
- B-6.02 Cleans surface of deck
- B-6.03 Verifies placement of roof penetrations, curbs and parapets
- B-6.04 Dries deck
CInstalls low slope roofing30%38152
C-7 · Applies low slope roofing components
18 official exam questions · 64 in the practice bank
- C-7.01 Installs support panels
- C-7.02 Primes substrate
- C-7.03 Applies vapour retarder, vapour barrier and air barrier
- C-7.04 Installs insulation
- C-7.05 Installs cover board
- C-7.06 Installs drains, vents, curbs and penetrations
- C-7.07 Applies ballast, walkways and protective surfaces
- C-7.08 Installs metal flashings
C-8 · Applies low slope roofing membranes
20 official exam questions · 88 in the practice bank
- C-8.01 Relaxes membranes
- C-8.02 Sets membranes
- C-8.03 Applies membranes using hot-liquid process
- C-8.04 Applies membranes using torched-on method
- C-8.05 Applies membranes using hot-air welding
- C-8.06 Applies membranes using cold-applied methods
- C-8.07 Applies membranes using mechanical fasteners
- C-8.08 Applies loose-laid membranes
- C-8.09 Applies liquid-applied membranes
- C-8.10 Installs membrane flashings
- C-8.11 Installs temporary seals and temporary drains
DInstalls steep slope roofing14%1768
D-9 · Performs common steep slope practices
6 official exam questions · 20 in the practice bank
- D-9.01 Installs steep slope underlayment
- D-9.02 Installs steep slope venting
- D-9.03 Installs steep slope valley applications
- D-9.04 Installs steep slope saddlescrickets
- D-9.05 Installs steep slope penetration flashings
D-10 · Applies shingles
6 official exam questions · 24 in the practice bank
- D-10.01 Determines layout of shingles
- D-10.02 Installs starter strip and starter course
- D-10.03 Fastens shingles
- D-10.04 Cuts shingles
- D-10.05 Tabs shingles
- D-10.06 Installs metal flashings for shingled roofs
D-11 · Applies roof tiles
2 official exam questions · 12 in the practice bank
- D-11.01 Installs battensstrapping for roof tiles
- D-11.02 Fastens roof tiles
- D-11.03 Cuts roof tiles
- D-11.04 Installs closure strips for roof tiles
- D-11.05 Installs ridge and hip caps
- D-11.06 Installs metal flashings for tiled roofs
D-12 · Applies pre-formed metal roofing
3 official exam questions · 12 in the practice bank
- D-12.01 Installs battensstrapping for pre-formed metal roofing
- D-12.02 Fastens pre-formed metal roofing
- D-12.03 Cuts sheet metal
- D-12.04 Installs closure strips for pre-formed metal roofing
- D-12.05 Installs snow guards
- D-12.06 Installs metal flashings for pre-formed metal roofs
EWaterproofs and damp-proofs surfaces10%1248
E-13 · Waterproofs surfaces
8 official exam questions · 34 in the practice bank
- E-13.01 Prepares waterproofing substrates
- E-13.02 Applies waterproofing membrane
- E-13.03 Installs green, sustainable, vegetative and protected membrane components
E-14 · Damp-proofs surfaces
4 official exam questions · 14 in the practice bank
- E-14.01 Applies damp-proofing materials
- E-14.02 Applies protection layer
FAssesses, maintains and repairs roof14%1768
F-15 · Assesses roof condition
5 official exam questions · 27 in the practice bank
- F-15.01 Performs roof inspections
- F-15.02 Performs cut test
- F-15.03 Determines maintenance or repair required
F-16 · Maintains and repairs low slope roofing
7 official exam questions · 23 in the practice bank
- F-16.01 Maintains low slope roofing
- F-16.02 Repairs low slope roofing
F-17 · Maintains and repairs steep slope roofing
5 official exam questions · 18 in the practice bank
- F-17.01 Maintains steep slope roofing
- F-17.02 Repairs steep slope roofing
Source: the official Roofer standard and exam breakdown. Check your own requirements with your province or territory.
Questions about Roofer exam prep
Study guideIs there a free Roofer Red Seal practice test?
Yes. Roofer Exam 1 is a full practice exam of 125 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.
Is there a Roofer practice test with answers?
Yes. Every Roofer practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.
How many questions are on the Roofer Red Seal exam?
The official Roofer Red Seal exam has 125 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 88 of 125 questions correct.
What topics are on the Roofer Red Seal exam?
The published exam breakdown has 6 Major Work Activities (MWAs) or blocks: A, Performs common occupational skills (23 questions); B, Prepares roof and deck (18 questions); C, Installs low slope roofing (38 questions); D, Installs steep slope roofing (17 questions); E, Waterproofs and damp-proofs surfaces (12 questions); F, Assesses, maintains and repairs roof (17 questions).
Use the full trade breakdown to review the tasks in every MWA, and the official RSOS or NOA for the subtasks of each task.
Can I challenge the Roofer Red Seal exam without an apprenticeship?
Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 125-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 4,000 in Ontario to 9,000 in Nunavut (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.
How do your Roofer practice exams follow the official breakdown?
Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.
What are Flashcard Match and Question Match?
Flashcard Match deals a board of Roofer flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Roofer practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.
How many Roofer practice exams are included?
Pass Your Red Seal includes 4 practice exams and 500 original practice questions for Roofer. Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 125 questions on the official exam.
Are Roofer flashcards included?
Yes. Every Roofer plan includes 250 flashcards in two exam-weighted sets of 125 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard - Roofer (2020) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.
Can I try Roofer practice questions for free?
Yes. Try 12 free Roofer questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.
How much does Roofer study access cost?
Study access for Roofer costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.
Challenge the Roofer exam without an apprenticeship
How it worksExperienced workers in the roofer trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.
| Province or territory, with its guide | Hours to challenge | Apprenticeship and certification |
|---|---|---|
| British Columbia | 7,425 | Apprenticeship 5,400 hours · voluntary certification |
| Alberta | 8,790 | Apprenticeship 6,400 hours · voluntary certification |
| Saskatchewan | 6,750 | Apprenticeship 4,500 hours · voluntary certification |
| Manitoba | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Ontario | 4,000 | Apprenticeship 4,000 hours · voluntary certification |
| Quebec | Quebec certificate first | Apprenticeship 4,000 hours · compulsory certification |
| New Brunswick | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Nova Scotia | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Prince Edward Island | 8,000 | Voluntary certification · PEI’s own Designated Trades page (15 September 2026) shows 8,100 challenger hours and a 5,400-hour apprenticeship; the province’s figure governs. |
| Newfoundland and Labrador | 8,100 | Voluntary certification |
| Yukon | 8,100 | Apprenticeship 5,400 hours · voluntary certification |
| Northwest Territories | 9,000 | Apprenticeship 7,200 hours · voluntary certification |
| Nunavut | 9,000 | Apprenticeship 7,200 hours · voluntary certification |
Source: Ellis Chart, Roofer, published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.