Pass Your Red Seal
Exams

Online Red Seal Exam Preparation, built on official standards

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

Glazier

Built on official standards for your trade

Practice exams split like the real exam.
Every answer explained.

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

6
Practice exams
720
Questions
240
Flashcards
1,000+
Flashcard Match
50+
Trade math
100+
Simulations
Try Glazier free12 sample questions now, or Exam 1 with a free account12 sample questionsFree Exam 1

Practice exams

6 exams · 120 questions each

Exam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works

6 practice exams and 720 original practice questions with answers and explanations, plus 240 flashcards in two exam-weighted sets, for the 120-question Glazier Red Seal exam. Timed or untimed, with pause and resume. 120 questions in the real exam · 4 hours · 70% pass mark.

Glazier sample exam questions

Take them as an exam

12 free practice questions with answers and explanations. No account needed.

Sample 1 Glazier, free sample

A four-sided window frame has verified opposite side lengths and straight members. Its installation detail permits at most 3 mm difference between diagonals. Repeated measurements between the same corner datums are 2,657 and 2,671 mm. What does this check establish before glazing?

Answer The 14 mm diagonal difference fails the specified squareness check
Why The difference is 2,671-2,657=14 mm, exceeding the 3 mm allowance. Seven millimetres is half that difference, not the specified diagonal comparison; it also exceeds the limit. Diagonal readings do not independently prove plumb, level or acceptable member bow. Reconcile the frame geometry and recheck all required installation dimensions before glazing.
2. A lifting assembly places 1.8 t through one shackle. Its manufacturer rates the shackle 2.0 t in line and permits the planned side-load angle only at 80% of that rating. All other checks are satisfactory. What capacity comparison applies to this configuration?
Answer Compare 1.8 t demand with the reduced 1.6 t shackle capacity
Why Apply the stated factor to the component rating: 2.0 × 0.80=1.6 t. The 1.8 t demand exceeds that capacity, requiring a revised approved arrangement. Keeping 2.0 t ignores the reduction. Multiplying the load by 0.80 gives 1.44 t but reduces the wrong quantity; adding 20% to load gives 2.16 t and is not the supplied capacity method. Manufacturer angle permissions and the complete lift plan still govern.
3. A captured curtain-wall method requires grid alignment acceptance before glazing, an accessible perimeter air/water seal inspection before infill blocks access, and pressure plates after glass placement. Which sequence preserves these hold points?
Answer Accept grid, inspect perimeter seals, place the glass, then fit pressure plates
Why The accepted grid establishes geometry before loading it with glass. The perimeter seals must be inspected while accessible, followed by glass and retaining plates. Setting glass before seal inspection blocks the stated access. Both glass-first alternatives also violate grid acceptance, and their later seals remain inaccessible. The supplied installation method sets this sequence; receptor arrangements vary by system.
4. An approved cutting method is being used on annealed laminated glass. The first glass ply has been scored and broken; the opposite ply and interlayer remain intact. Which next operation preserves aligned breaks before the interlayer is separated by the approved method?
Answer Score the opposite face on the matching line, then break the second glass ply
Why Each annealed glass ply needs its own aligned score and controlled break before the interlayer is separated. An offset opposite score creates mismatched glass edges. Repeated or deeper scoring of the first ply does not produce the required second-face score, and scoring glass does not replace the interlayer-separation method. The question does not permit cutting heat-treated glass or improvising heat or solvent procedures.
5. A bottom-hinged, inward-opening hopper sash has a manufacturer glazing diagram showing two setting blocks on its lower rail at prescribed support locations. What is the purpose of keeping the glass on those blocks rather than letting its edge sit directly on the metal rail?
Answer Carry the glass dead load through the supports and preserve the edge clearance
Why The setting blocks provide the specified support path and keep the glass edge clear of hard metal contact. Treating the sealant as the dead-load support substitutes an unapproved load path. Eliminating edge clearance allows damaging glass-to-metal contact whether blocks or sealant are claimed as support. The block positions come from this sash diagram, not a universal quarter-point rule. A hopper sash is bottom-hinged.
6. A heavy fixed window installation detail identifies sill support points, jamb anchor backing and drainage openings. The empty frame is square, but trial loading causes the sill to deflect between supports. What must be resolved before final glazing?
Answer Check and correct the detailed load support without obstructing drainage
Why The load trial reveals inadequate support under the specified loading, so reconcile the sill support with the approved detail and verify the loaded geometry while retaining drainage. Blocking drain paths introduces a water-management defect. Jamb or head anchor torque alone does not establish the missing sill support and leaves the observed deflection. Supporting locations and adjustments must follow the system design.
7. An insulating-glass-unit order specifies the laminated lite on the room side and low-emissivity coating on surface 3. Surface numbers run from outdoors to indoors across the four exposed glass faces. Which orientation follows that order?
Answer Place the laminated lite indoors with its coated face toward the cavity
Why Surface 3 is the cavity-facing surface of the inner lite, so the laminated lite is indoors with its coated face toward the cavity. Its room-facing face is surface 4. Reversing the laminated lite to outdoors changes the specified safety-glazing placement; its cavity/weather faces are surfaces 2/1. Actual coating and laminated-lite locations depend on the ordered performance and design, not a universal heating-climate rule.
8. A skylight drawing gives a horizontal projection of 1,854 mm along a rafter sloping 22° above horizontal. Use cos 22°=0.927. What true slope distance corresponds to those same endpoints before applying the separately specified glazing clearances?
Answer Select 2,000 mm along the slope by dividing the projection by cosine
Why Horizontal projection equals slope distance times cosine. Thus 1,854/0.927=2,000 mm. Multiplication gives about 1,719 mm and shortens a dimension that must be longer on the slope. Retaining 1,854 ignores slope; adding 22 treats degrees as millimetres. This computes endpoint geometry, not final glass cut size; apply the design clearances and fabrication allowances separately.
9. A custom shower-panel detail requires its door-hinge edge vertical and its wall edge following a measured wall taper. Templates show the upper wall is 6 mm farther into the opening than the lower wall. The glass will be tempered after fabrication. Which action preserves the required geometry?
Answer Template the wall taper while retaining a vertical door-hinge edge
Why The fabrication template must include the wall taper independently of the vertical hinge reference. Making the hinge edge lean with the wall violates the intended swing axis. Either post-tempering edge-trimming option is incompatible with fabrication of tempered glass; geometry and required holes are established beforehand. Channel or sealant tolerances cannot be assumed when the supplied detail requires a shaped panel.
10. After a concealed vertical-rod exit-device replacement, the top latch engages but the bottom bolt stops 3 mm above a correctly located floor strike. The manufacturer procedure permits bottom-rod length adjustment. What repair addresses the observed fault while retaining both latches?
Answer Adjust the bottom-rod length and verify both latches through release
Why The bottom bolt lacks travel to a strike whose location is verified, so use the permitted bottom-rod adjustment and then check both latching and release through the full device cycle. Adjusting the top rod changes the functioning upper latch. A wider floor opening does not make the short bolt reach it, and shifting the head strike does not correct the stated bottom-rod travel. Preserve the approved exit-device function.
11. A wood-sash assessment finds soft material and loss of section inside the lower rail-to-stile joint; the sash moves at that joint under the inspection load. The glass and operator are serviceable. Which repair scope is supported before returning the sash to service?
Answer Assess repair or replacement of the structural joint before refinishing its surface
Why Section loss and movement at the load-carrying corner require a structural repair/replacement assessment. Refinishing alone cannot restore missing joint capacity. Replacing a serviceable operator or reglazing sound glass addresses components not implicated by the evidence and leaves the structural defect. The assessment does not automatically condemn the entire sash when a suitable engineered or manufacturer repair may be possible.
12. An overhead curved-glazing schedule requires a factory-bent laminated replacement with a specified radius, thickness and edge-retention detail. A cracked lite has been safely secured pending replacement. What procurement decision conforms to that schedule?
Answer Order the specified bent laminate and verify its radius and make-up
Why Radius and laminated make-up must match the approved overhead assembly along with its retained-edge detail. Matching colour alone does not establish structural and geometric compatibility. Neither flat-laminate nor flat-tempered substitutions are authorized to be bent by the pressure plates in this schedule. Some systems are specifically engineered for cold bending, but that does not authorize converting the supplied factory-bent system.

Start free

Interactive simulations

Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.

Diagrams and symbols

Learn to read the diagrams and schematic symbols used in your trade.

How things work

Animated section drawings show what happens inside the equipment as it runs.

Terminology

Learn the correct name and job of every part.

Exam breakdown

Red Seal practice tests and exam prep

The official Glazier Red Seal exam, also called the interprovincial (IP) exam, has 120 questions across 5 topic blocks. Open a block to see its tasks and subtasks.

120
Multiple choice questions
4 hours
Writing time
70%
Pass mark
Major Work Activity% of examReal examPractice bank
APerforms common occupational skills17%20120

A-1 · Performs safety-related functions

2 official exam questions · 8 in the practice bank

  • A-1.01 Maintains a safe work environment
  • A-1.02 Uses personal protective equipment (PPE) and safety equipment

A-2 · Uses tools and equipment

4 official exam questions · 24 in the practice bank

  • A-2.01 Uses hand tools
  • A-2.02 Uses portable and stationary power tools
  • A-2.03 Uses layout and measuring equipment
  • A-2.04 Uses access equipment

A-3 · Uses rigging, hoisting and lifting equipment

2 official exam questions · 8 in the practice bank

  • A-3.01 Uses rigging equipment
  • A-3.02 Uses hoisting and lifting equipment

A-4 · Organizes work

4 official exam questions · 20 in the practice bank

  • A-4.01 Uses documentation and reference material
  • A-4.02 Interprets plans, drawings and specifications
  • A-4.03 Prepares list of materials and supplies
  • A-4.04 Plans project tasks

A-5 · Performs routine trade activities

6 official exam questions · 52 in the practice bank

  • A-5.01 Prepares worksite
  • A-5.02 Handles glass and other materials
  • A-5.03 Prepares materials for installation
  • A-5.04 Stores glass and other materials
  • A-5.05 Performs glass cutting and edge treatment
  • A-5.06 Installs building envelope membranes
  • A-5.07 Installs flashing
  • A-5.08 Applies sealants

A-6 · Uses communication and mentoring techniques

2 official exam questions · 8 in the practice bank

  • A-6.01 Uses communication techniques
  • A-6.02 Uses mentoring techniques
BFabricates and installs commercial window and door systems34%41246

B-7 · Fabricates commercial window and door systems

14 official exam questions · 78 in the practice bank

  • B-7.01 Fabricates curtain walls
  • B-7.02 Fabricates storefronts
  • B-7.03 Fabricates window systems
  • B-7.04 Fabricates skylights and sloped glazing systems
  • B-7.05 Fabricates entrance systems

B-8 · Installs commercial window and door systems

27 official exam questions · 168 in the practice bank

  • B-8.01 Lays out commercial window and door systems
  • B-8.02 Installs curtain wall systems
  • B-8.03 Installs storefront systems
  • B-8.04 Installs window systems
  • B-8.05 Installs skylights and sloped glazing systems
  • B-8.06 Installs entrance systems
CInstalls residential window and door systems14%17102

C-9 · Installs residential window systems

10 official exam questions · 88 in the practice bank

  • C-9.01 Lays out residential window systems
  • C-9.02 Sets windows in openings
  • C-9.03 Glazes windows

C-10 · Installs residential door systems

7 official exam questions · 14 in the practice bank

  • C-10.01 Lays out residential door systems
  • C-10.02 Assembles residential door frames
  • C-10.03 Sets residential doors and frames
  • C-10.04 Installs residential door hardware
  • C-10.05 Glazes residential doors
DFabricates and installs specialty glass, products and glass systems16%19114

D-11 · Fabricates and installs commercial specialty glass and products

13 official exam questions · 75 in the practice bank

  • D-11.01 Lays out commercial specialty glass and products
  • D-11.02 Assembles commercial specialty glass, products and hardware
  • D-11.03 Installs commercial specialty glass, products and hardware

D-12 · Fabricates and installs residential specialty glass and products

6 official exam questions · 39 in the practice bank

  • D-12.01 Lays out residential specialty glass and products
  • D-12.02 Assembles residential specialty glass, products and hardware
  • D-12.03 Installs residential specialty glass, products and hardware
EPerforms servicing19%23138

E-13 · Services commercial window and door systems

13 official exam questions · 74 in the practice bank

  • E-13.01 Assesses service requirements for commercial window and door systems
  • E-13.02 Repairs commercial window and door systems

E-14 · Services residential window and door systems

6 official exam questions · 38 in the practice bank

  • E-14.01 Assesses service requirements for residential window and door systems
  • E-14.02 Repairs residential window and door systems

E-15 · Services specialty glass and products

4 official exam questions · 26 in the practice bank

  • E-15.01 Assesses service requirements for specialty glass and products
  • E-15.02 Repairs specialty glass and products

Source: the official Glazier standard and exam breakdown. Check your own requirements with your province or territory.

Questions about Glazier exam prep

Study guide
Is there a free Glazier Red Seal practice test?

Yes. Glazier Exam 1 is a full practice exam of 120 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.

Is there a Glazier practice test with answers?

Yes. Every Glazier practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.

How many questions are on the Glazier Red Seal exam?

The official Glazier Red Seal exam has 120 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 84 of 120 questions correct.

What topics are on the Glazier Red Seal exam?

The published exam breakdown has 5 Major Work Activities (MWAs) or blocks: A, Performs common occupational skills (20 questions); B, Fabricates and installs commercial window and door systems (41 questions); C, Installs residential window and door systems (17 questions); D, Fabricates and installs specialty glass, products and glass systems (19 questions); E, Performs servicing (23 questions).

Can I challenge the Glazier Red Seal exam without an apprenticeship?

Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 120-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 7,200 in New Brunswick to 10,800 in Yukon (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.

How do your Glazier practice exams follow the official breakdown?

Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.

What are Flashcard Match and Question Match?

Flashcard Match deals a board of Glazier flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Glazier practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.

How many Glazier practice exams are included?

Pass Your Red Seal includes 6 practice exams and 720 original practice questions for Glazier. Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 120 questions on the official exam.

Are Glazier flashcards included?

Yes. Every Glazier plan includes 240 flashcards in two exam-weighted sets of 120 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard – Glazier (2020) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.

Can I try Glazier practice questions for free?

Yes. Try 12 free Glazier questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.

How much does Glazier study access cost?

Study access for Glazier costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.

Challenge the Glazier exam without an apprenticeship

How it works

Experienced workers in the glazier trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.

Experience required to challenge the Glazier Red Seal exam
Province or territory, with its guideHours to challengeApprenticeship and certification
British Columbia9,990Apprenticeship 7,200 hours · voluntary certification
Alberta9,720Apprenticeship 7,200 hours · voluntary certification
Saskatchewan10,800Apprenticeship 7,200 hours · voluntary certification
Manitoba10,800Apprenticeship 7,200 hours · voluntary certification
Ontario
Architectural Glass and Metal Technician
8,000Apprenticeship 8,000 hours · voluntary certification
Quebec
Erector Mechanic (Glazier)
Quebec certificate firstApprenticeship 6,000 hours · compulsory certification
New Brunswick7,200Voluntary certification
Nova Scotia10,800Apprenticeship 7,200 hours · voluntary certification
Prince Edward Island10,000Voluntary certification
Newfoundland and Labrador10,800Voluntary certification
Yukon10,800Apprenticeship 7,200 hours · voluntary certification
Northwest Territories9,000Apprenticeship 7,200 hours · voluntary certification
Nunavut9,000Apprenticeship 7,200 hours · voluntary certification

Source: Ellis Chart, Glazier, published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.