Online Red Seal Exam Preparation, built on official standards
Carpenter
Built on official standards for your trade
Practice exams split like the real exam.
Every answer explained.
- 10
- Practice exams
- 1,000
- Questions
- 200
- Flashcards
- 1,000+
- Flashcard Match
- 50+
- Trade math
- 100+
- Simulations
Practice exams
10 exams · 100 questions eachExam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works
10 practice exams and 1,000 original practice questions with answers and explanations, plus 200 flashcards in two exam-weighted sets, for the 100-question Carpenter Red Seal exam. Timed or untimed, with pause and resume. 100 questions in the real exam · 4 hours · 70% pass mark.
Carpenter sample exam questions
Take them as an exam12 free practice questions with answers and explanations. No account needed.
What does a green triangle on CSA-certified safety footwear indicate?
2. A free-standing scaffold tower has a 1.5 m by 2.1 m base and no outriggers. Under Canadian Centre for Occupational Health and Safety scaffold guidance, above what height does it need tying, guying or an increased effective base?
3. Inside a house, an open landing is 2.7 m above the floor below. What guard does the NBC require along its edge?
4. A product label on site shows the WHMIS pictogram of a flame on top of a circle. How should the product be stored?
5. On a cast-in-place concrete stair, why is the bottom edge of each riser form board bevelled?
6. When is a fresh concrete slab bull-floated, and why?
7. Rafters on a 6/12 gable roof meet at a ridge board, with no ridge beam or bearing wall below. What stops them from pushing the walls apart?
8. A plumber needs to notch the top edge of a 38 x 235 mm floor joist. Under the NBC, where may it be notched, and how deep at most?
9. A heated house in a cold region is getting asphalt shingles on a 5/12 roof. Under the NBC, how far up the roof must the eave protection reach?
10. Gypsum board on a wall has been finished to Level 4. What added work brings it to a Level 5 finish?
11. A stair inside a house has a total rise of 2 870 mm, 14 equal risers and a 260 mm run. How does it compare with the NBC?
12. A spalled area of an existing concrete landing will be patched with cement-based repair mortar, without a separate bonding agent. How is the repair area prepared?
Start free
Interactive simulations
Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.
Learn to read the diagrams and schematic symbols used in your trade.
Animated section drawings show what happens inside the equipment as it runs.
Learn the correct name and job of every part.
Exam breakdown
Red Seal practice tests and exam prepThe official Carpenter Red Seal exam, also called the interprovincial (IP) exam, has 100 questions across 7 topic blocks. Open a block to see its tasks and subtasks.
- 100
- Multiple choice questions
- 4 hours
- Writing time
- 70%
- Pass mark
APerforms common occupational skills12%12120
A-1 · Uses and maintains tools and equipment
4 official exam questions · 45 in the practice bank
- A-1.01 Uses hand, power and pneumatic tools
- A-1.02 Uses stationary tools
- A-1.03 Uses powder-actuated tools
- A-1.04 Uses lifting, rigging and hoisting equipment
- A-1.05 Uses layout instruments and equipment
- A-1.06 Uses tack welding equipment (Not Common Core)
- A-1.07 Uses torch cutting equipment (Not Common Core)
A-2 · Performs safety-related activities
3 official exam questions · 24 in the practice bank
- A-2.01 Uses personal protective equipment (PPE) and safety equipment
- A-2.02 Maintains safe work environment
A-3 · Builds and uses temporary access structures
3 official exam questions · 33 in the practice bank
- A-3.01 Uses stationary access equipment
- A-3.02 Uses mobile access equipment
- A-3.03 Erects/dismantles scaffolding
- A-3.04 Modifies scaffolding
A-4 · Uses communication and mentoring techniques
2 official exam questions · 18 in the practice bank
- A-4.01 Uses communication techniques
- A-4.02 Uses mentoring techniques
BPerforms planning and layout14%14140
B-5 · Interprets documentation
5 official exam questions · 42 in the practice bank
- B-5.01 Interprets project drawings
- B-5.02 Interprets specifications
- B-5.03 Interprets safety documentation
- B-5.04 Interprets workplace documentation
B-6 · Organizes work
3 official exam questions · 26 in the practice bank
- B-6.01 Schedules work sequence
- B-6.02 Performs site preparation
- B-6.03 Performs quantity takeoff
- B-6.04 Organizes material
B-7 · Performs layout
6 official exam questions · 72 in the practice bank
- B-7.01 Performs site layout
- B-7.02 Lays out concrete formwork
- B-7.03 Lays out floors
- B-7.04 Lays out decks
- B-7.05 Lays out walls
- B-7.06 Lays out ceilings
- B-7.07 Lays out roofs
- B-7.08 Lays out stairs
- B-7.09 Lays out balustrades
CPerforms concrete work16%16160
C-8 · Constructs formwork
12 official exam questions · 121 in the practice bank
- C-8.01 Erects excavation shoring and underpinning
- C-8.02 Erects concrete falsework
- C-8.03 Constructs footing forms
- C-8.04 Constructs wall form systems and grade beam formwork
- C-8.05 Constructs slab formwork
- C-8.06 Constructs column formwork
- C-8.07 Constructs stair formwork
- C-8.08 Installs embedded reinforcements
- C-8.09 Dismantles formwork
C-9 · Installs concrete, cement-based and epoxy products
4 official exam questions · 39 in the practice bank
- C-9.01 Places concrete
- C-9.02 Facilitates curing of concrete
- C-9.03 Performs basic concrete finishing
- C-9.04 Installs pre-cast components
- C-9.05 Installs grout
DPerforms framing20%20200
D-10 · Constructs floor systems
6 official exam questions · 60 in the practice bank
- D-10.01 Installs engineered floor systems
- D-10.02 Constructs dimensional lumber floor framing
D-11 · Constructs deck systems
3 official exam questions · 32 in the practice bank
- D-11.01 Constructs decks
- D-11.02 Installs deck components
D-12 · Constructs wall systems
6 official exam questions · 58 in the practice bank
- D-12.01 Installs engineered wall systems
- D-12.02 Constructs dimensional lumber wall framing
D-13 · Constructs roof and ceiling systems
5 official exam questions · 50 in the practice bank
- D-13.01 Installs engineered trusses
- D-13.02 Constructs roof and ceiling framing
EPerforms exterior finishing14%14140
E-14 · Installs exterior doors and windows
5 official exam questions · 62 in the practice bank
- E-14.01 Installs exterior jambs/frames
- E-14.02 Installs exterior doors
- E-14.03 Installs exterior windows
- E-14.04 Installs exterior door and window hardware
E-15 · Installs roofing
4 official exam questions · 36 in the practice bank
- E-15.01 Installs roofing components
- E-15.02 Installs roof coverings
E-16 · Installs exterior finishes
5 official exam questions · 42 in the practice bank
- E-16.01 Installs exterior wall components
- E-16.02 Installs exterior wall coverings
FPerforms interior finishing14%14140
F-17 · Applies wall and ceiling finishes
3 official exam questions · 33 in the practice bank
- F-17.01 Installs wallboard
- F-17.02 Applies compound to walls and ceilings
- F-17.03 Installs panels, tiles and solid wood finishes
- F-17.04 Installs suspended ceilings
- F-17.05 Installs demountable wall systems
F-18 · Installs flooring
2 official exam questions · 21 in the practice bank
- F-18.01 Installs underlayment
- F-18.02 Installs floor coverings
- F-18.03 Installs access flooring
F-19 · Installs interior doors and windows
4 official exam questions · 44 in the practice bank
- F-19.01 Installs interior jambs/frames
- F-19.02 Installs interior doors
- F-19.03 Installs interior windows
- F-19.04 Installs interior door and window hardware
F-20 · Constructs and installs finish components and stairs
5 official exam questions · 42 in the practice bank
- F-20.01 Fabricates finish components
- F-20.02 Installs finish components and accessories
- F-20.03 Constructs stairs
GPerforms renovations10%10100
G-21 · Performs renovation-specific support activities
5 official exam questions · 55 in the practice bank
- G-21.01 Removes existing material
- G-21.02 Protects structure during renovations
G-22 · Performs renovation-specific construction activities
5 official exam questions · 45 in the practice bank
- G-22.01 Joins new to existing construction
- G-22.02 Changes existing structure during renovations
Source: the official Carpenter standard and exam breakdown. Check your own requirements with your province or territory.
Questions about Carpenter exam prep
Study guideIs there a free Carpenter Red Seal practice test?
Yes. Carpenter Exam 1 is a full practice exam of 100 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.
Is there a Carpenter practice test with answers?
Yes. Every Carpenter practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.
How many questions are on the Carpenter Red Seal exam?
The official Carpenter Red Seal exam has 100 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 70 of 100 questions correct.
What topics are on the Carpenter Red Seal exam?
The published exam breakdown has 7 Major Work Activities (MWAs) or blocks: A, Performs common occupational skills (12 questions); B, Performs planning and layout (14 questions); C, Performs concrete work (16 questions); D, Performs framing (20 questions); E, Performs exterior finishing (14 questions); F, Performs interior finishing (14 questions); G, Performs renovations (10 questions).
Use the full trade breakdown to review the tasks in every MWA, and the official RSOS or NOA for the subtasks of each task.
Can I challenge the Carpenter Red Seal exam without an apprenticeship?
Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 100-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 7,200 in Ontario to 10,800 in Newfoundland and Labrador (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.
How do your Carpenter practice exams follow the official breakdown?
Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.
What are Flashcard Match and Question Match?
Flashcard Match deals a board of Carpenter flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Carpenter practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.
How many Carpenter practice exams are included?
Pass Your Red Seal includes 10 practice exams and 1,000 original practice questions for Carpenter. Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 100 questions on the official exam.
Are Carpenter flashcards included?
Yes. Every Carpenter plan includes 200 flashcards in two exam-weighted sets of 100 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard - Carpenter (2022) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.
Can I try Carpenter practice questions for free?
Yes. Try 12 free Carpenter questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.
How much does Carpenter study access cost?
Study access for Carpenter costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.
Challenge the Carpenter exam without an apprenticeship
How it worksExperienced workers in the carpenter trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.
| Province or territory, with its guide | Hours to challenge | Apprenticeship and certification |
|---|---|---|
| British Columbia | 9,540 | Apprenticeship 7,200 hours · voluntary certification |
| Alberta | 9,360 | Apprenticeship 7,200 hours · voluntary certification |
| Saskatchewan | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Manitoba | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Ontario General Carpenter | 7,200 | Apprenticeship 7,200 hours · voluntary certification |
| Quebec Carpenter-Joiner | Quebec certificate first | Apprenticeship 6,000 hours · compulsory certification |
| New Brunswick | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Nova Scotia | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Prince Edward Island | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Newfoundland and Labrador | 10,800 | Apprenticeship 7,200 hours · voluntary certification |
| Yukon | 9,600 | Apprenticeship 6,400 hours · voluntary certification |
| Northwest Territories | 9,000 | Apprenticeship 7,200 hours · voluntary certification |
| Nunavut | 9,000 | Apprenticeship 7,200 hours · voluntary certification |
Source: Ellis Chart, Carpenter, published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.