Pass Your Red Seal

Refrigeration and Air Conditioning Mechanic Flashcard Match

Online Red Seal Exam Preparation, built on official standards
Flashcard Match10 pairs · 1 decoyChecked at the endStart matching

Set up a round

Cards from

Pairs per round

Blocks

Decoys

250 cards to draw from

ACommon occupational skills20
BRoutine trade activities40
CPlans installation32
DInstallation52
ECommissioning44
FMaintenance and service62

Your rounds

Kept on this device
Average79%
Best100%

Checking

What a checked pair looks like
Browse the 20 free cards and explanations

After the supply is isolated and locked out, a capacitor still measures 170 V. What must happen before its terminals can be handled?

Answer: Discharge it using the equipment-specific safe procedure and verify that stored electrical energy is removed.

Opening the supply prevents new energy entering but does not remove energy already stored in a capacitor. The discharge method and subsequent verification must suit the equipment.

Exam trap: Shorting the terminals with a screwdriver can release the stored energy violently; a locked disconnect alone does not make them safe.

Standard reference: RSOS 2024 A-1.02.03P

An apprentice correctly demonstrates a service procedure and clearly repeats the job instructions. A coworker still excludes them from the task solely because of their accent. What should guide task assignment?

Answer: The demonstrated competence and understood safety instructions, with the discriminatory exclusion addressed.

The demonstration establishes task skill and the repeat-back establishes understanding. Accent alone does not negate either finding or justify unequal access to suitable work.

Exam trap: Treating accent as evidence of poor comprehension ignores the apprentice’s demonstrated understanding.

Standard reference: RSOS 2024 A-1.04.06P

An R-290 system requires recovery, but the available machine is approved only for A1 and A2L refrigerants. What machine capability must be obtained for this job?

Answer: A recovery machine specifically approved for R-290, a safety-class A3 refrigerant.

R-290 is a highly flammable refrigerant. A machine’s approval must cover that refrigerant and safety class; a pressure rating or general recovery capability does not establish ignition safety.

Exam trap: A2L approval does not include the higher flammability of A3 refrigerants, even if the pressure rating is adequate.

Standard reference: RSOS 2024 B-4.04.01P

A floor opening must remain uncovered while piping is lowered through it beside a pedestrian route. How should the surrounding work area be controlled?

Answer: Provide a secured protective barrier and divert pedestrians away from the opening.

The opening must be physically separated from people who do not need access to the work. A protected alternate route maintains circulation without exposing passersby to the fall hazard.

Exam trap: A caution sign alone warns of the opening but does not prevent someone stepping into it.

Standard reference: RSOS 2024 B-6.01.06P

An evacuation procedure requires verification at 500 microns absolute. The manifold’s compound gauge has 5 kPa divisions. What instrument is needed to verify this target?

Answer: An appropriately ranged absolute vacuum gauge capable of resolving the target in microns.

A coarse compound gauge cannot resolve pressure accurately in the deep-vacuum range. An absolute vacuum instrument measures against zero pressure and provides the needed resolution.

Exam trap: A needle appearing at the vacuum end of the compound scale does not verify a 500-micron absolute target.

Standard reference: RSOS 2024 B-7.03.01P

An outdoor heat pump and proposed indoor coil have the same nominal tonnage and compatible pipe connections. The performance certificate lists a different indoor-coil model. Can its certified efficiency be assigned to this combination?

Answer: No. Establish the certified performance of the exact proposed indoor/outdoor combination.

Nominal capacity and connection fit do not identify a tested combination. The certificate’s different model means its efficiency has not been established for the proposed pairing.

Exam trap: A physically connectable coil does not inherit another combination’s certified rating.

Standard reference: RSOS 2024 C-8.02.05P

A speed pickup produces two pulses per revolution at 6 000 r/min. Its pulse voltage suits a proposed input, but that input accepts at most 150 Hz. Is the input suitable?

Answer: No. The pickup produces 200 Hz, exceeding the input’s 150 Hz limit.

6 000/60 = 100 revolutions per second; two pulses each gives 200 pulses per second. Correct signal voltage does not satisfy the separate frequency limit.

Exam trap: Checking voltage alone can miss pulses that the input cannot count at operating speed.

Standard reference: RSOS 2024 C-9.02.02P

A retrofit survey measures 1 000 L/s entering a supply trunk and 700 L/s at all its terminals on the same density basis. With terminals sealed, that isolated trunk needs continuous make-up flow to hold test pressure. What should be repaired before adding fan capacity?

Answer: Supply-duct leakage between the trunk inlet and terminal outlets.

The inlet-to-outlet flow deficit and independent leakage test identify lost delivery in the distribution path. More fan capacity would not repair that path.

Exam trap: The room airflow shortage alone might suggest an undersized fan; the measured trunk inflow and leakage evidence change that conclusion.

Standard reference: RSOS 2024 C-10.03.02P

A keyed coupling hub stops short of its specified shaft position. Without the key it slides correctly; the installed key is visibly too tall for the hub keyway. What assembly correction is indicated?

Answer: Fit the correctly specified key before assembling the hub.

The fit comparison isolates key interference from shaft-to-bore fit. Forcing the hub on can damage the keyway or prevent correct seating.

Exam trap: Driving the hub harder does not correct an oversized key.

Standard reference: RSOS 2024 D-11.02.04P

A coil being removed currently carries the weight of two connected pipe runs. The replacement will arrive after removal. What preparation is needed before those connections are released?

Answer: Install suitable temporary pipe supports so the old coil no longer carries the pipe loads.

The retrofit changes the load path. Supporting the retained piping prevents it from dropping or loading adjacent joints when the old component is disconnected.

Exam trap: Isolating and draining a circuit removes fluid hazards but does not support the remaining pipework.

Standard reference: RSOS 2024 D-11.05.04P

A control module’s address switches are weighted 1, 2, 4, 8 and 16. The installation schedule calls for address 21. Which switch weights must be ON?

Answer: 1, 4 and 16.

Add the enabled binary weights: 1 + 4 + 16 = 21. Leave weights 2 and 8 off.

Exam trap: Switch positions are weighted values, not the decimal digits of the requested address.

Standard reference: RSOS 2024 D-12.01.06P

A controller terminal is approved for one conductor only. Two field wires must join that same circuit point. How should they be connected?

Answer: Join them through a suitable approved distribution terminal, with one conductor to the controller terminal.

The separate distribution point provides the required branch while respecting the controller terminal’s conductor limit. Each termination must suit its conductor type and size.

Exam trap: Two wires fitting under a clamp does not mean that clamp is approved to hold both securely.

Standard reference: RSOS 2024 D-12.02.08P

A clamp meter encloses all three phase conductors of a balanced running motor and reads nearly zero. Where should it be placed to measure one phase current?

Answer: Around one insulated phase conductor only, using the appropriate safe measurement procedure.

The magnetic fields of the balanced phase currents largely cancel when all phases pass through the jaw. Enclosing one conductor measures that conductor’s current.

Exam trap: A near-zero reading around the complete cable does not show that a running motor draws no current.

Standard reference: RSOS 2024 E-13.02.07P

A three-way mixing valve has hot water at A, cool return at B and mixed outlet AB. During setup, what happens to mixed outlet temperature when the valve admits more A flow and less B flow at unchanged inlet temperatures?

Answer: The mixed outlet temperature rises.

Increasing the hot-water proportion raises the mixture temperature. This follows the stated mixing arrangement; a diverting arrangement must be interpreted using its own port diagram.

Exam trap: Assuming every three-way valve diverts outlet flow ignores the specified two-inlet mixing arrangement.

Standard reference: RSOS 2024 E-13.05.05P

For a cooling coil model, what does the air bypass factor represent?

Answer: The equivalent fraction of air that leaves without reaching the coil’s apparatus dew-point condition.

The model represents the leaving-air condition as a mixture of air at the apparatus dew point and an unchanged bypass fraction. It is an equivalent thermal model, not necessarily a visible physical gap.

Exam trap: Interpreting bypass factor only as air leaking around the cabinet misses its heat-transfer meaning.

Standard reference: RSOS 2024 E-14.03.01L

A fan bearing became hot immediately after receiving four times its specified grease charge. Speed, belt load and vibration are unchanged, and its grease outlet is blocked. What maintenance fault should be addressed first?

Answer: Excess retained grease causing churning and heat.

The excessive charge and blocked escape path can pack the bearing with grease. The timing and unchanged mechanical duty favour over-lubrication rather than a new load increase.

Exam trap: Adding more grease because the bearing is hot can worsen the churning already supported by the service history.

Standard reference: RSOS 2024 F-15.02.03P

What two functions does the interstage heat exchanger perform in a two-circuit cascade refrigeration system?

Answer: It condenses the low-temperature circuit’s refrigerant and evaporates the high-temperature circuit’s refrigerant.

The circuits exchange heat without mixing their refrigerants. Heat rejected by the low stage becomes an evaporator load on the high stage.

Exam trap: Calling it an evaporator for both circuits misses the low-stage condensation required to reject that circuit’s heat.

Standard reference: RSOS 2024 F-16.01.01L

A motor-run capacitor is safely discharged and absence of voltage is verified, but it remains connected to the motor windings. How should it be prepared for a direct capacitance measurement?

Answer: Isolate it electrically from the circuit before measuring its capacitance.

Connected windings and other circuit paths can affect a direct capacitance reading. Separating the capacitor lets the instrument test the component rather than the combined network.

Exam trap: A safe discharge removes stored energy but does not remove the parallel paths that can distort the measurement.

Standard reference: RSOS 2024 F-16.01.06L

A replacement blower wheel has been positioned for the specified housing clearances. Its hub uses a set screw and the shaft has a machined flat. Where should the screw seat before the required tightening?

Answer: On the shaft’s machined flat.

The flat provides the intended seating surface for the screw and helps prevent hub movement without raising a burr on the cylindrical shaft surface. Recheck clearances after tightening.

Exam trap: Tightening on the round shaft can damage that surface and fail to establish the intended hub seating.

Standard reference: RSOS 2024 F-16.02.08P

At one reference pressure, a transmitter settles at 402 kPa after approach from below and 418 kPa after approach from above. The reference stays at 410 kPa and the pattern repeats after long holds. What error characteristic is demonstrated?

Answer: Hysteresis: the settled indication depends on the direction of approach.

The same stable input produces two repeatable settled outputs depending on prior pressure direction. Longer holds exclude a simple settling delay, and a fixed offset cannot remove both opposite errors.

Exam trap: Treating this as one zero error ignores that the error changes sign with the direction of approach.

Standard reference: RSOS 2024 F-17.03.02P

10 pairs · 1 decoyChecked at the end