Agricultural Equipment Technician Flashcard Match
Online Red Seal Exam Preparation, built on official standardsSet up a round
Cards from
Pairs per round
Blocks
Decoys
250 cards to draw from
Your rounds
Kept on this device- 80%10 pairs · 4:12TodayRetry the wrong ones
- 70%10 pairs · 4:40TodayRetry the wrong ones
- 87%15 pairs · 6:05YesterdayRetry the wrong ones
- 100%10 pairs · 3:3111 NovPlay again
- 60%5 pairs · 2:2010 NovRetry the wrong ones
Checking
What a checked pair looks likeChecking
Clock
How a round works
Each card is the front of a flashcard from the set you chose.
Drag it onto its answer, or tap the card and then the answer. Every miss shows the right pair and the why behind it.
Browse the 20 free cards and explanations
A tractor's common transmission-hydraulic oil looks milky. Lab analysis shows 0.4% water, no glycol, and sodium and potassium at baseline. The tractor sat outdoors all spring with its reservoir breather cap missing. What is the most likely source of the water?
Answer: Rain and condensation entering through the uncapped breather opening; it is external water ingress, not a coolant leak.
Coolant carries glycol plus additive elements such as sodium and potassium, so a cooler or seal leak raises those markers along with water. Here water is present but the coolant markers are absent, and the reservoir was open to the weather for weeks. Fit a breather cap, drain and flush, replace the filters, refill and resample.
Exam trap: An internal oil-to-coolant cooler leak; it would also show glycol and raised sodium and potassium in the analysis, and those markers are absent.
Standard reference: RSOS 2021 A-2.02.06P
A diesel's oil pressure is normal cold but low at hot idle. The dipstick level has risen since the last oil change, the oil feels thin and smells of diesel, and the coolant level is steady. What condition explains all of these findings?
Answer: Fuel dilution of the engine oil, caused by diesel fuel leaking into the crankcase.
Fuel entering the crankcase raises the oil level, thins the oil and gives it a fuel odour. Diluted oil thins further when hot and leaks through bearing clearances faster, so pressure falls at hot idle. A steady coolant level rules out coolant. Next, find the source, such as a leaking injector seal or transfer pump seal, and confirm with oil analysis.
Exam trap: A worn oil pump or bearings; they lower hot oil pressure but would not raise the oil level or make the oil smell of fuel.
Standard reference: RSOS 2021 B-6.02.02P
A diesel with a mechanical in-line injection pump misses at idle. During a cut-out test, loosening each injector line nut in turn drops engine speed on every cylinder except No. 3, where nothing changes. What is the correct next step?
Answer: Remove the No. 3 injector and test it on an injector tester for opening pressure, spray pattern and leakage.
Cutting out a working cylinder lowers engine speed; no change means No. 3 was already not contributing. Its injector is the most likely cause and is easily bench-tested for opening pressure, atomization and dribble. If it passes, check No. 3's compression and pump element. Wrap loosened nuts with a rag and keep hands clear of high-pressure fuel.
Exam trap: Replacing the injection pump; a pump fault usually affects several cylinders, and the test has isolated one cylinder whose injector is quick to check.
Standard reference: RSOS 2021 B-6.05.05P
A replacement turbocharger failed after 40 hours. Its shaft is blued at the bearing journals, both wheels are undamaged, engine oil pressure is normal, and the original oil supply line was reused at installation. What must be corrected before another turbo is fitted?
Answer: Oil starvation: replace the reused, likely restricted oil feed line and prime the new turbo with clean oil before start-up.
Blued journals show bearing overheating from lack of oil, and undamaged wheels rule out foreign objects. With normal engine oil pressure, oil is being lost between the gallery and the turbo, and old feed lines often hold carbon or sludge that restricts flow. Check supply pressure at the turbo and the drain for restriction, and prime the bearings before cranking.
Exam trap: Foreign object damage from an intake leak; that nicks or bends compressor blades, but both wheels are undamaged.
Standard reference: RSOS 2021 B-7.04.04P
A tractor's hydraulically released dry clutch releases normally at first, but gears clash if the pedal is held down at a stop, and the held pedal slowly sinks to the floor. Reservoir level is unchanged after a week and there are no external leaks. What is the most likely cause?
Answer: Internal leakage past the primary (master) cylinder piston seal, letting fluid bypass back to the reservoir under sustained pressure.
A held pedal that sinks means pressure is bleeding off. With no external leaks and no fluid loss, the fluid must be returning internally past the primary cylinder's piston cup. As pressure falls, the secondary (slave) cylinder retracts, the clutch begins to re-engage and the gears clash.
Exam trap: Air in the lines gives a spongy, low pedal from the first stroke, but it does not make a held pedal creep down. A leaking secondary cylinder would lose fluid externally.
Standard reference: RSOS 2021 C-8.01.02P
A tractor's left outboard planetary final drive, which has its own oil supply, is overfull and pushing oil out of its breather. The transmission/rear-axle reservoir needs regular topping up, and the right final drive level is normal. What is the most likely cause?
Answer: A failed left inner axle seal, letting oil migrate from the centre housing into the left final drive.
A separate-oil final drive is sealed from the centre housing by an inner axle seal. One compartment rising while the shared reservoir falls means oil is transferring between them, not leaking out. Only the left side is affected, so the left inner seal has failed. Replace it and correct both oil levels.
Exam trap: Overfilling at the last service would also show a high level, but it would not keep drawing down the transmission reservoir.
Standard reference: RSOS 2021 C-8.04.03P
A rebuilt powershift clutch pack measures 2.6 mm pack clearance (piston stroke) with its original 3.0 mm end plate; spec is 1.5–2.0 mm. Selective end plates come in 3.3, 3.6, 3.9 and 4.2 mm. Which plate brings the clearance closest to the middle of the spec?
Answer: The 3.9 mm plate, which reduces clearance by 0.9 mm to 1.7 mm.
A thicker end plate takes up clearance millimetre for millimetre. Mid-spec is 1.75 mm, so about 0.85 mm must be removed. 3.3 mm gives 2.3 mm (out of spec), 3.6 mm gives 2.0 mm (at the limit), 3.9 mm gives 1.7 mm and 4.2 mm gives 1.4 mm (too tight). The 3.9 mm plate lands closest to 1.75 mm.
Exam trap: The 3.6 mm plate gives 2.0 mm, technically in spec but at the upper limit, leaving no margin as the discs wear and clearance grows.
Standard reference: RSOS 2021 C-9.03.05P
A gear pump specified at 90 L/min at 2 200 rpm and 17 000 kPa is flow-tested with warm oil at 1 100 rpm low idle and delivers 46 L/min at 17 000 kPa. What should be concluded from this test?
Answer: Nothing condemns the pump: about 45 L/min is expected at half speed. Retest at the rated 2 200 rpm and compare with the 90 L/min spec.
Positive-displacement pump flow is proportional to shaft speed: 90 × 1 100 ÷ 2 200 = 45 L/min. The 46 L/min reading matches that, but the spec is written for rated rpm, so the test must be repeated at rated rpm and operating temperature before the result can be compared.
Exam trap: Calling the pump worn because 46 L/min is about half of 90 L/min ignores that the test was run at half the specified speed.
Standard reference: RSOS 2021 D-10.01.08P
With the engine running and a trailer connected, a master gauge on a tractor's air reservoir confirms governor cut-out at 830 kPa. How is the governor's cut-in pressure measured next?
Answer: Keep the engine running, fan the trailer brakes to lower reservoir pressure, and note where pressure stops falling and starts to rise as the compressor loads.
Cut-in is the pressure at which the governor exhausts the unloader signal and the compressor loads again. Repeated brake applications use air while the compressor stays driven, so pressure falls until the governor cuts in; the reading where pressure stops falling and climbs is cut-in, compared with the spec and differential.
Exam trap: Shutting the engine off and draining a reservoir loses the reading, because the compressor can't resume pumping to show where cut-in occurs.
Standard reference: RSOS 2021 D-10.02.08P
A chafed section of nylon air-brake tubing on a tractor is being replaced using push-to-connect fittings. How should the new tubing be cut and installed?
Answer: Cut it square with a plastic-tubing cutter, check the end is round and clean, push it in to full depth, then pull-test and leak-test the joint.
Push-to-connect fittings seal on an O-ring and grip with a collet. An angled, crushed or burred end from side cutters or a hacksaw can damage the O-ring or fail to seat fully, causing leaks or blow-out. Marking insertion depth and pull-testing confirm the tube is locked.
Exam trap: Side cutters seem quick, but they pinch the tube oval and leave an angled end that won't seal reliably.
Standard reference: RSOS 2021 D-11.02.01P
A combine's 12 V batteries go flat after a week parked. With an ammeter in series at the negative cable and the controllers allowed to go to sleep, the draw is 320 mA against a scenario spec of 50 mA maximum. What is the next step to find the source?
Answer: Isolate the circuit: remove fuses one at a time (or read the millivolt drop across each fuse) to find the circuit carrying the draw.
Parasitic draw is traced by isolating circuits while the meter stays in series. When the fuse feeding the faulty circuit is pulled, the reading falls toward spec; measuring the tiny voltage drop across each fuse in place finds the same circuit without waking modules. That circuit is then traced to the component left powered.
Exam trap: Replacing the batteries is tempting, but 320 mA is an external load on a sleeping machine; new batteries would be drained the same way.
Standard reference: RSOS 2021 E-12.01.06P
A sprayer's 3-wire Hall-effect wheel speed sensor (12 V supply, ground, signal) shows no speed on the monitor. Supply and ground are confirmed good at the connector. How is the sensor's output checked?
Answer: Back-probe the signal wire with the sensor connected and turn the wheel slowly; the signal should switch cleanly between near 0 V and its high level.
A Hall-effect sensor is a powered switching device: its output turns on and off as each target tooth or magnet passes, producing a square-wave digital signal. Turning the wheel slowly lets a DMM show the high and low states; an oscilloscope shows the square wave at working speed.
Exam trap: Measuring coil resistance or AC output is the test for a 2-wire magnetic pickup; a Hall-effect sensor has no pickup coil and generates no AC voltage.
Standard reference: RSOS 2021 E-12.02.05P
A tractor's hydraulic oil temperature reading seems wrong. The sensor is a 2-wire NTC thermistor, and the OEM supplies a resistance-versus-temperature chart. What is the correct way to bench-test it?
Answer: Measure its resistance at two or more known temperatures, confirmed with a thermometer, and compare each reading to the OEM chart.
An NTC thermistor's resistance falls as its temperature rises. One room-temperature reading proves only one point; a sensor can be right cold and wrong hot. Heating it in oil or water beside a thermometer and checking resistance at several temperatures against the chart proves the whole curve.
Exam trap: Checking resistance once at room temperature is tempting, but a sensor that passes at 20°C can still drift or stick at operating temperature.
Standard reference: RSOS 2021 E-12.02.02L
A replacement armrest controller is installed in a tractor. Its power, ground and CAN wiring all test good. It appears on the network but reports a software version unlike the other controllers and sets an 'invalid configuration' code. What is the next step?
Answer: Program the controller with the correct software and machine configuration using the OEM service tool.
Replacement controllers often ship blank or with generic software and must be loaded with machine-specific software and configuration before they will operate. Good power, ground and CAN wiring plus a controller visible on the bus show the hardware works; the version mismatch and configuration code show it is not set up yet.
Exam trap: Returning the controller as defective is tempting, but it powers up and communicates; the version mismatch and configuration code show it simply has not been programmed for this machine.
Standard reference: RSOS 2021 E-13.02.03P
An orbital steering control unit that leaked only externally was resealed. On start-up, the steering wheel turns by itself and the front wheels steer to a stop with no input. The hoses are on their original ports. What is the most likely cause?
Answer: The gerotor (star) was mistimed to the drive shaft during reassembly, so the unit motors; disassemble and retime it to the OEM marks.
The metering gerotor and the spool-and-sleeve valve must be timed so metered oil turns the sleeve to close the valve. Mistimed, the oil drives the gerotor so it opens the valve further: the steering wheel spins and the axle runs to a stop. The fault appeared right after reassembly and the hoses are unchanged.
Exam trap: Swapped cylinder hoses make the wheels steer the wrong way when the wheel is turned, but they don't make the steering wheel rotate by itself.
Standard reference: RSOS 2021 F-15.01.03P
A tractor's suspended front axle rides harshly, and the accumulator's nitrogen precharge is to be checked with a charging and gauge kit. What must be done on the hydraulic side before reading the precharge?
Answer: Relieve all hydraulic pressure on the accumulator's oil side, following the OEM procedure, so the gauge reads the true precharge.
With oil pressure in the accumulator, the gas is compressed to system pressure and the gas-side gauge reads that pressure, not the precharge. Only with the oil side at 0 kPa does the gauge show the nitrogen charge for comparison with spec. Relieving pressure also prevents injury when connecting the kit.
Exam trap: Reading it with the engine running and the suspension active shows suspension oil pressure, which hides a low precharge.
Standard reference: RSOS 2021 F-16.03.03P
Over a season, a tractor's cab heat has gradually weakened. Coolant is full and at 88 °C, the heater valve is fully open and blower airflow is strong. An infrared thermometer reads 82 °C at the heater core inlet tube and 38 °C at the outlet tube. What is the most likely cause?
Answer: A restricted (internally plugged) heater core, which limits coolant flow so most of the core runs cool.
A healthy core passes enough coolant that its outlet runs only modestly cooler than its inlet. A 44 °C drop with strong airflow means little coolant is moving through it, so most tubes stay cold. Hot coolant reaching the inlet clears the engine and valve, and the gradual decline fits sediment build-up. Flush or replace the core.
Exam trap: A stuck-closed heater valve also gives weak heat, but then the core inlet would be cool too; here 82 °C coolant reaches the inlet.
Standard reference: RSOS 2021 G-20.01.05P
What is the minimum number of satellites a GNSS receiver must track to calculate a 3D position fix, and why?
Answer: Four: three satellite ranges to fix position, plus a fourth to solve for the receiver's clock error.
A receiver finds its distance to each satellite from the signal's travel time. Three ranges would fix a point only if the receiver's clock were perfect, but its clock error is a fourth unknown, so a fourth satellite is needed. On site, a receiver tracking fewer than four satellites cannot report a position at all, so guidance will not engage.
Exam trap: Three is tempting from map triangulation, but it assumes a perfect receiver clock; with the clock error unknown, three ranges cannot give a 3D fix.
Standard reference: RSOS 2021 H-23.01.01L
A double-shoot air cart has one fan supplying both the seed and fertilizer runs. At a high fertilizer rate the fertilizer runs plug at the openers, while the seed runs flow cleanly at the same fan speed. What adjustment should be made?
Answer: Reset the damper to send a larger share of the air to the fertilizer runs, then check run air flow against the manual's setting.
Plugging means the fertilizer stream lacks the air velocity to carry its heavier load. The damper sets the split between the two streams, so shifting air toward the fertilizer side fixes it without disturbing the seed runs, which are already flowing correctly.
Exam trap: Raising fan speed adds air to the seed runs too; they are already right, and excess seed-run velocity can crack seed and bounce it out of the furrow.
Standard reference: RSOS 2021 H-26.02.09P
A sprayer is to apply 100 L/ha at 16 km/h with nozzles on 50 cm spacing. A catch test at operating pressure averages 1.20 L/min per nozzle. What output is required per nozzle, and what rate is actually being applied?
Answer: Required: 1.33 L/min per nozzle. Actual: 90 L/ha, 10% under the 100 L/ha target.
L/min = L/ha × km/h × spacing (cm) ÷ 60 000 = 100 × 16 × 50 ÷ 60 000 = 1.33 L/min. Rearranged: L/ha = L/min × 60 000 ÷ (km/h × cm) = 1.20 × 60 000 ÷ (16 × 50) = 72 000 ÷ 800 = 90 L/ha.
Exam trap: Calling 1.20 L/min close enough to 1.33: the 0.13 L/min shortfall is a 10% under-application on every hectare sprayed.
Standard reference: RSOS 2021 H-29.01.07P