Pass Your Red Seal

Glazier Flashcard Match

Online Red Seal Exam Preparation, built on official standards
Flashcard Match10 pairs · 1 decoyChecked at the endStart matching

Set up a round

Cards from

Pairs per round

Blocks

Decoys

240 cards to draw from

ACommon occupational skills40
BFabricates and installs commercial window and door systems82
CInstalls residential window and door systems34
DFabricates and installs specialty glass, products and glass systems38
EServicing46

Your rounds

Kept on this device
Average79%
Best100%

Checking

What a checked pair looks like
Browse the 20 free cards and explanations

A CRL2 glass drill is changed from a steel tube bit to a diamond tube bit. Silicon-carbide abrasive slurry remains ready for use. What working medium should be used with the diamond bit?

Answer: Use the specified diamond-bit coolant without silicon-carbide abrasive grain.

The CRL2 manual distinguishes loose-abrasive steel/brass tube drilling from diamond tube drilling. Silicon-carbide grain must not be used with its diamond bit.

Exam trap: Changing the bit does not make the old loose-abrasive slurry suitable for the new cutting system.

Standard reference: RSOS 2020 A-2.02.01P

A drawing gives a frame dimension as 31 7/8 in. What metric dimension should be recorded to the nearest millimetre?

Answer: 810 mm.

31 7/8 in = 31.875 in. Multiplying by 25.4 mm/in gives 809.625 mm, which rounds to 810 mm.

Exam trap: Multiplying only 31 and treating 7/8 as a metric fraction loses the stated fractional-inch dimension.

Standard reference: RSOS 2020 A-4.02.05P

Several small adjacent lites will be cut from Pilkington Warwick patterned stock. A yield-only layout puts some lites at the nearly clear sheet edges. What layout change is needed?

Answer: Centre and coordinate the pattern coverage/direction of adjacent lites before optimizing yield.

Warwick’s pattern is concentrated toward the stock-sheet centre. A small edge cut can contain little pattern; appearance and comparable adjacent coverage must govern the cutting layout as well as yield.

Exam trap: Maximum pieces per sheet alone can produce adjacent lites with visibly unequal pattern coverage.

Standard reference: RSOS 2020 A-5.05.04P

A pressure plate is cut at stock datum 200 mm; its next factory fastener hole is at 228.6 mm. The YCW detail requires the end hole 38.1 mm from the new cut end. Is that factory hole usable, and where should the replacement axis lie on the stock datum?

Answer: No; seal the hole 28.6 mm from the end and drill the replacement at stock datum 238.1 mm.

The remaining factory-hole offset is 228.6−200=28.6 mm, below 38.1 mm. The replacement axis is 200+38.1=238.1 mm. The YCW detail requires sealing and not using a factory hole that lies too close to the cut end.

Exam trap: The stock datum is not the new cut end; compare the difference before accepting the factory hole.

Standard reference: RSOS 2020 B-7.01.12P

SU 311-30T has stood eight minutes after pouring; nominal debridging time is five minutes, but release requires at least Shore D 65. It measures D 60, and Bridgemill wheels press against the filled profile to feed it. Should it be fed now?

Answer: No; wait until the measured hardness meets the Shore D 65 release requirement.

The nominal five-minute time is not the release test. D 60 is below D 65, and soft polymer can compress under the feed wheels, producing kickback. Both cure evidence and the feeding mechanism argue against release.

Exam trap: Elapsed time can look satisfactory while the actual material remains too soft for the machine's feed forces.

Standard reference: RSOS 2020 B-7.03.01P

What is the purpose of a turning point when transferring a benchmark elevation through several optical-level setups?

Answer: It preserves the transferred elevation between successive instrument setups.

Take a foresight on a stable turning point before moving the level, then a backsight on that same point from the next setup. This joins the elevation calculations across the instrument move.

Exam trap: Taking the next backsight on a different nearby spot breaks the elevation transfer.

Standard reference: RSOS 2020 B-8.01.01L

A WPG MRTALPCH6 lifter is rated at a 60 kPa pad pressure difference. While glazing curtain-wall lites at an elevated site, it reaches only 50 kPa; seals and pump pass checks. Would lowering its minimum-lift switch setting restore its original rated holding capacity?

Answer: No. A lower switch threshold changes lift permission, not the pad pressure difference or original holding capacity.

Actual pad pressure difference has not increased. Changing the switch does not turn 50 kPa into the 60 kPa rating condition. WPG warns that lower minimum-lift vacuum can reduce capacity and requires consultation before lowering it.

Exam trap: Silencing a warning can change control permission while the actual vacuum remains below the rating condition.

Standard reference: RSOS 2020 B-8.02.01P

An approved storefront trim joint has two 2.0 mm members. Same-diameter rivet A has a 1.6–3.2 mm grip range; rivet B has a 3.2–4.8 mm range. Which grip range fits the joint?

Answer: Rivet B, with the 3.2–4.8 mm grip range.

Total joint thickness=2.0+2.0=4.0 mm. B covers 4.0 mm; A stops at 3.2 mm. Grip selection uses the complete stack, while diameter and joint capacity remain the separately approved conditions.

Exam trap: Considering only one 2.0 mm member wrongly selects a rivet too short for the assembled joint.

Standard reference: RSOS 2020 B-8.03.04P

A UniVent opening limiter is removed for anchor access; two of its screws also secure the hinge. The limiter cannot yet be refitted. What temporary fastening step preserves hinge attachment during this stage?

Answer: Reinstall the shared screws securing the hinge while the limiter is out.

The UniVent detail uses two limiter fasteners that also secure the hinge. Temporary limiter removal for anchor access must not leave those hinge attachment positions empty.

Exam trap: Removing a limiter does not authorize removing fastening that it shares with the hinge.

Standard reference: RSOS 2020 B-8.04.02P

For an electrified entrance lock, what does fail secure describe when electrical power is removed?

Answer: The secure access side remains locked when power is removed.

Fail secure describes the lock's power-loss condition on the secure side. It does not by itself define every inside-egress function or prescribe a Canadian fire-door application.

Exam trap: Fail secure is not a statement that every user on both sides is trapped by a power failure.

Standard reference: RSOS 2020 B-8.06.01L

A traditional double-hung window is being removed for an insert conversion. The upper sash remains raised on its old cords. What sash positioning is needed before those cords are cut?

Answer: Lower the upper sash to the sill before cutting its support cords.

In this insert-conversion sequence, the sill supports the upper sash when the cords are severed. Cutting while it is raised can release an unsupported sash.

Exam trap: Its present cord support will disappear as soon as those cords are cut.

Standard reference: RSOS 2020 C-9.01.03P

Reusable wood trim is being removed during Andersen impact-window reglazing. Its nails remain through the trim after removal. How should the nails be withdrawn to protect the finished face?

Answer: Pull the nails through the back of the trim.

The reglazing guide directs withdrawing retained nails through the back. Reversing them through the finished face can tear or damage the face intended for reuse.

Exam trap: Pushing the nails back along their entry path can damage the visible finish.

Standard reference: RSOS 2020 C-9.03.01P

An Andersen Architectural Clad inswing door installation has its flange fastened but its supplied installation clips remain unfastened. The normal detail calls for both. Is the frame fastening complete?

Answer: No; complete both clip and flange fastening, or use the approved through-frame alternative.

The stated installation detail requires both attachment systems. Fastening only the flange leaves the specified frame attachment unfinished; a different attachment method requires the approved alternative detail.

Exam trap: One visibly fastened attachment is not evidence that all required attachments are complete.

Standard reference: RSOS 2020 C-10.03.03P

What is the purpose of an acoustic PVB interlayer in laminated glass?

Answer: Damp sound-induced vibration to improve sound insulation.

A suitably formulated acoustic interlayer dissipates vibrational energy. Its sound-control role is additional to the laminate’s fragment-retention function.

Exam trap: Assuming every PVB interlayer provides the same acoustic damping.

Standard reference: RSOS 2020 D-11.01.01L

A threshold beside an adjustable floor-closer body needs anchoring. The closer must remain movable for door alignment. Should threshold screws secure it through that closer body or into the fixed surrounding structure?

Answer: Anchor into the fixed surrounding structure.

The closer body must remain adjustable for alignment. Using it to secure the threshold couples a fixed component to the part that must move, obstructing the intended adjustment.

Exam trap: Choosing the closer body as a convenient nearby screw substrate.

Standard reference: RSOS 2020 D-11.03.05P

An open, unbraced glass cabinet relies on its bonded corners to hold the shape. A proposed adhesive remains highly elastic, allowing those corners to rotate under load. What assembly design issue must be resolved?

Answer: The open assembly needs adequate joint stiffness or a suitably revised, self-stabilizing geometry.

An elastic adhesive may suit a closed, self-stabilizing construction but let unsupported corners rotate in an open cabinet. Select an approved joint system for the actual assembly mechanics.

Exam trap: Treating satisfactory adhesion to glass as proof that a flexible joint can stabilize any cabinet shape.

Standard reference: RSOS 2020 D-12.02.01L

A pinless moisture scan of a curtain-wall sill is attempted through aluminum cladding. The meter is a Tramex MEX5. Can that scan establish moisture in concealed material behind the metal?

Answer: No. The conductive covering prevents a valid scan of the material behind it.

The MEX5 non-destructive method cannot measure through that metal covering. Assess the concealed material by a suitable access or alternative method rather than interpreting the scan as dry or wet.

Exam trap: Treating an invalid reading through aluminum as a moisture finding about the hidden substrate.

Standard reference: RSOS 2020 E-13.01.02P

Why can a free-radical acrylic light-curing repair adhesive retain a tacky air-exposed surface even when the material below has polymerized?

Answer: Oxygen in the air can inhibit free-radical polymerization at the exposed surface.

Henkel describes oxygen inhibition in free-radical acrylic light-cure systems. The air interface can remain tacky while material below polymerizes. This mechanism does not establish overall cure acceptance or apply equally to every adhesive chemistry.

Exam trap: Treating tack at the air interface as proof that all material below has failed to polymerize.

Standard reference: RSOS 2020 E-13.02.02L

A reflective patio-door surface gives inconsistent infrared temperatures. A high-emissivity reference patch has just been applied to the glass. What must happen before its reading can represent glass-surface temperature?

Answer: Let the patch thermally equilibrate with the glass before measuring it.

The reference has useful emissivity but initially may have a different temperature. Correct emissivity cannot make a non-equilibrated patch represent the glass-surface temperature.

Exam trap: Assuming a newly applied high-emissivity patch instantly has the glass temperature.

Standard reference: RSOS 2020 E-14.01.02P

A replacement mirror has a vinyl safety backing, and QwikSet mirror mastic is proposed for its installation. What compatibility issue must be resolved before the repair proceeds?

Answer: QwikSet is not approved for the vinyl safety backing.

The mirror’s backing forms part of the actual bonding system. Select an attachment method approved for that backing rather than assuming any mirror mastic is compatible.

Exam trap: Choosing mastic from mirror dimensions while ignoring the backing material.

Standard reference: RSOS 2020 E-15.01.05P

10 pairs · 1 decoyChecked at the end