Pass Your Red Seal

Machinist Flashcard Match

Online Red Seal Exam Preparation, built on official standards
Flashcard Match10 pairs · 1 decoyChecked at the endStart matching

Set up a round

Cards from

Pairs per round

Blocks

Decoys

270 cards to draw from

ACommon occupational skills26
BBenchwork22
CMachines using power saws16
DMachines using drill presses18
EMachines using conventional lathes56
FMachines using conventional milling machines56
GMachines using precision grinding machines22
HMachines using computer numerical control (CNC) machines54

Your rounds

Kept on this device
Average79%
Best100%

Checking

What a checked pair looks like
Browse the 20 free cards and explanations

What does a rectangular box around a basic dimension mean on a GD&T drawing?

Answer: It is a theoretically exact dimension whose permissible variation is controlled by the associated geometric tolerance.

The boxed value establishes exact geometry for the tolerance framework. It is not treated as an ordinary plus/minus dimension.

Exam trap: Applying the title-block linear tolerance to the boxed value misinterprets a basic dimension.

Standard reference: RSOS 2018 A-2.01.02L

Only one end of an alloy bar carries its heat number. The bar will be divided into several blanks, and each blank must remain traceable to the material report. When and where should the identity be transferred?

Answer: Transfer the heat identity to every resulting blank and retained remnant before their original identity can be lost.

Marking or the approved shop identification method must preserve the link between each piece and its heat record during cutting and storage.

Exam trap: Marking only the first blank leaves identical-looking pieces without a reliable material history.

Standard reference: RSOS 2018 A-4.03.02P

A keyway side wall needs hand filing, but the adjacent finished bottom must retain its dimension. Which file feature should contact the bottom while the teeth cut the side wall?

Answer: A safe edge with no cutting teeth.

A safe edge can bear against the finished adjoining surface while the toothed face removes metal from the intended wall. Confirm the file geometry fits the corner.

Exam trap: A toothed edge against the bottom can deepen the keyway while the side is being fitted.

Standard reference: RSOS 2018 B-6.03.01P

Two line-bored bearing caps were removed without location marks. During trial reassembly, both journals bind although the caps fit either bolt pattern and no burrs are found. What lost disassembly information is most likely responsible?

Answer: The original cap-to-housing pairing and orientation.

Line-bored caps and housings form matched bores. Record and mark their locations and orientation before separation so similar-looking caps return to the correct positions.

Exam trap: Identical bolt patterns do not make individually machined caps interchangeable.

Standard reference: RSOS 2018 B-7.01.04P

A power hacksaw makes 60 complete reciprocating cycles per minute and cuts on one stroke of each cycle. The set downfeed is 0.08 mm per cutting stroke. What is the resulting downfeed per minute?

Answer: 4.8 mm/min.

There are 60 cutting strokes per minute. Multiply 60 x 0.08 = 4.8 mm/min; the return strokes do not add cutting downfeed.

Exam trap: Counting both strokes as cutting strokes doubles the result incorrectly.

Standard reference: RSOS 2018 C-8.04.01L

A drill chuck has a 1.5–13 mm gripping capacity. A 16 mm drill has a 10 mm reduced shank. Does the drill’s cutting diameter alone prevent it from fitting the chuck?

Answer: No. Its 10 mm shank is within the chuck’s gripping range.

Chuck capacity describes the diameter held by its jaws. A reduced shank can fit even when the cutting diameter is larger; the drilling machine and holder must separately have adequate operating capacity.

Exam trap: Rejecting the drill solely because 16 mm exceeds 13 mm confuses cutting diameter with gripping diameter.

Standard reference: RSOS 2018 D-10.05.03P

A sleeve needs a deep bore and a thin finished wall. Both surfaces still have roughing stock. Which sequence retains more support during heavy internal cutting?

Answer: Rough-bore while the outside remains thick, then complete the specified finishing sequence.

Leaving external stock preserves wall stiffness during heavy boring. After bulk internal removal, the outside and bore can be finished with appropriate allowances and support.

Exam trap: Finishing the outside first leaves the weakest wall to resist the heavy boring forces.

Standard reference: RSOS 2018 E-12.02.02P

A round shaft runs true beside the chuck but shows increasing radial runout farther along its length. Its reference surfaces are straight. What alignment fault does this pattern indicate?

Answer: The shaft is tilted relative to the spindle axis, rather than simply offset parallel to it.

A parallel offset produces similar eccentricity along a straight reference cylinder. Runout that grows with distance identifies angular seating error, requiring the work to be seated and indicated at separated locations.

Exam trap: Adjusting only until the indicator reads zero beside the jaws can leave the far end orbiting.

Standard reference: RSOS 2018 E-12.06.03P

A stepped shaft has a 0.5 mm maximum shoulder fillet. The available turning inserts have 0.4 mm and 0.8 mm nose radii. Which is geometrically suitable for that corner?

Answer: The 0.4 mm nose-radius insert.

Its nose can produce a fillet within the 0.5 mm maximum. The 0.8 mm nose would leave too large a radius even if the adjoining diameter and shoulder position were correct.

Exam trap: Selecting the larger nose solely for strength can prevent the mating component from seating at the shoulder.

Standard reference: RSOS 2018 E-13.02.01P

A two-wheel knurling holder must produce a male diamond pattern. Which pair of wheel tooth directions is required?

Answer: One right-hand diagonal wheel and one left-hand diagonal wheel of matching pitch.

The two opposite diagonal tracks intersect to form diamonds. Both wheels must be a compatible pair, including pitch and the holder’s intended arrangement.

Exam trap: Two diagonal wheels of the same hand reinforce parallel tracks instead of creating the required crossed pattern.

Standard reference: RSOS 2018 E-13.07.02P

Temporary pads locate a casting for a later bore. Milling the outer contour would remove those pads, and no replacement locating features exist yet. Which operation should be delayed?

Answer: Delay removing the pads until the later bore is complete or an approved replacement location is established.

A usable reference must survive until all operations depending on it are finished. The sequence must preserve location rather than assume it can be recreated from an unfinished contour.

Exam trap: Completing the outer shape first can remove the only repeatable reference for the bore.

Standard reference: RSOS 2018 F-14.02.02P

A dividing-head crank pin is seated, yet the spindle can turn freely by hand. The head was just changed from direct indexing to worm indexing. What engagement should be checked?

Answer: Check that the worm is engaged with the spindle worm wheel.

The crank pin can restrain the crank while a disengaged worm leaves the spindle disconnected from it. Restoring the intended drive engagement is necessary before relying on worm indexing.

Exam trap: Changing the selected hole circle cannot restrain a spindle disconnected from the worm.

Standard reference: RSOS 2018 F-14.05.04P; F-14.05.01L

A pocket must finish between X0.00 and X40.00, each wall within ±0.02 mm. The rough pocket is only 39.80 mm wide, but its measured walls are X0.30 and X40.10. Can a finishing enlargement bring both walls to specification?

Answer: No. The X40.10 wall is already 0.10 mm beyond its nominal boundary; cutting cannot restore that missing material.

An undersize width does not prove that finish stock remains on every wall. The near wall still needs removal, but the far wall exceeds even the X40.02 limit. Stop for disposition rather than assuming a centred finish pass can recover it.

Exam trap: Splitting the 0.20 mm width shortage equally between the walls ignores their actual locations.

Standard reference: RSOS 2018 F-15.02.04P; F-15.02.05P

A sharp straight-flute reamer catches at a cross-hole in a through bore. Stock allowance is correct and chips clear freely. What flute geometry should be considered for the interrupted bore?

Answer: A suitable helical-flute reamer, commonly right-hand cutting with a left-hand spiral for a through hole.

The helix crosses the interruption progressively instead of presenting an entire straight edge to it at once. Left-hand spiral through-hole designs also direct chips forward.

Exam trap: Reducing the reaming allowance below its proper range does not correct the interruption-sensitive flute geometry.

Standard reference: RSOS 2018 F-15.06.05P; F-15.06.06P

A magnetic chuck firmly holds a clean steel test coupon but barely attracts a clean, flat austenitic stainless part spanning the same poles. What setup limitation should be checked first?

Answer: Whether the stainless grade is sufficiently magnetic for this workholding method.

The successful coupon test makes a general chuck failure less likely. Some austenitic stainless grades provide too little magnetic attraction, so a suitable mechanical fixture may be needed.

Exam trap: Turning up chuck power does not make an unsuitable alloy reliably ferromagnetic.

Standard reference: RSOS 2018 G-16.03.01L

A blind bore is 80 mm deep. A straight internal-grinding wheel is 10 mm wide axially and must stay 1 mm clear of the floor. How deep may its centre travel from the bore mouth?

Answer: 74 mm.

The leading wheel face is half its width beyond the centre. Maximum centre depth is 80 - 1 - (10 / 2) = 74 mm.

Exam trap: Setting the centre at 79 mm clears the centreline from the floor but drives half the wheel width into it.

Standard reference: RSOS 2018 G-17.03.01L

In a CNC program, what distinguishes a dwell from a feed move?

Answer: A dwell pauses axis motion for a programmed time; a feed move changes position at a specified feed rate.

The dwell controls elapsed time at a location rather than distance travelled. Its code and time units must follow the actual control manual.

Exam trap: A very low feed still moves the tool and does not establish a fixed pause at one position.

Standard reference: RSOS 2018 H-18.02.01L

In CAM, what does toolpath chordal tolerance limit?

Answer: The permitted geometric deviation of the approximated toolpath from its intended curve or surface.

A curved path may be approximated by short segments. Chordal tolerance controls that approximation error; it does not guarantee final part accuracy, which also depends on the machine, tooling and setup.

Exam trap: Treating it as the drawing’s entire dimensional tolerance ignores other machining errors.

Standard reference: RSOS 2018 H-18.06.05P

When CNC soft jaws are bored for outside gripping, why is a jaw-forming ring used?

Answer: To load and position the jaws during machining so their bored shape represents the clamped condition.

The forming ring supports boring with the jaws loaded in the intended gripping direction and position. The chuck manufacturer’s procedure governs pressure, stroke and ring placement.

Exam trap: Boring freely positioned, unloaded jaws may not reproduce their shape and position under clamping load.

Standard reference: RSOS 2018 H-19.03.03P

Why can chips left in a CNC pocket damage the cutting edge even when programmed speed and feed are correct?

Answer: The cutter can recut trapped chips, imposing extra impacts and loads on its edge.

Poor evacuation lets detached chips re-enter the cut. The edge must strike or cut those chips again, adding local loads beyond the intended cut. Correct programmed cutting data does not prevent this mechanism.

Exam trap: Assuming correct speed and feed rule out chip-related edge damage.

Standard reference: RSOS 2018 H-20.02.03P

10 pairs · 1 decoyChecked at the end