Pass Your Red Seal

Automotive Service Technician Flashcard Match

Online Red Seal Exam Preparation, built on official standards
Flashcard Match10 pairs · 1 decoyChecked at the endStart matching

Set up a round

Cards from

Pairs per round

Blocks

Decoys

250 cards to draw from

ACommon occupational skills18
BDiagnoses and repairs engine and engine support systems44
CDiagnoses and repairs vehicle module communications systems24
DDiagnoses and repairs driveline systems34
EDiagnoses and repairs electrical and comfort control systems46
FDiagnoses and repairs steering and suspension, braking, control systems, tires, hubs and wheel bearings46
GDiagnoses and repairs restraint systems, body components, accessories and trim20
HDiagnoses and repairs hybrid and electric vehicles (EV) systems18

Your rounds

Kept on this device
Average79%
Best100%

Checking

What a checked pair looks like
Browse the 20 free cards and explanations

When an oxy-acetylene outfit is set up to heat a seized suspension bolt, what is the highest acetylene working pressure that may be set on the regulator?

Answer: 103 kPa (15 psi); above that, free acetylene becomes unstable and can decompose explosively even without oxygen.

Acetylene is stored dissolved in acetone inside a porous filler because the free gas is unstable under pressure. Above about 103 kPa (15 psi) free acetylene can decompose violently from heat or shock alone, so the regulator is never set higher. The cylinder also stays upright so acetone is not drawn out with the gas.

Exam trap: Setting it to match the oxygen pressure or a large heating tip's demand; no tip size justifies free acetylene above 103 kPa, where it can decompose.

Standard reference: RSOS 2023 A-2.01.04L

A V6's serpentine belt keeps walking forward off the crankshaft pulley. A laser tool shows all the other pulleys in one plane. With the engine turned by hand, a dial indicator reads 1.5 mm runout on the crank pulley's grooved outer ring but 0.03 mm on its centre hub. What is the most likely cause?

Answer: A failed crankshaft torsional damper: its grooved inertia ring has slipped on the rubber insert and now runs out of plane with the hub.

The crank pulley is a torsional damper: a grooved inertia ring bonded to the hub through a rubber insert. When the rubber fails, the ring shifts and wobbles while the hub stays true. The laser clears the other pulleys, and 1.5 mm runout at the ring against 0.03 mm at the hub puts the fault between ring and hub, so the out-of-plane grooves push the belt forward.

Exam trap: A bent crankshaft snout; it would make the hub run out too, but the hub reads only 0.03 mm, so the ring has shifted on its rubber insert.

Standard reference: RSOS 2023 B-4.04.09P

A four-cylinder waste-spark engine with firing order 1-3-4-2 sets P0301 and P0304 together. Cylinder 1's plug wire measures open; cylinder 4's wire, both spark plugs, compression and both injectors test good. Why is cylinder 4 misfiring too?

Answer: Cylinders 1 and 4 are companions on one coil, wired in series, so the open cylinder 1 wire breaks the circuit and starves both plugs of spark.

In waste spark, each coil's secondary fires two companion cylinders at once: current leaves one coil terminal, jumps plug 1's gap to ground, then crosses plug 4's gap back to the coil. With firing order 1-3-4-2, cylinders 1 and 4 share a coil. An open in either wire opens that series circuit, so neither plug fires reliably, and one fault sets both codes.

Exam trap: A second fault in cylinder 4 such as a weak plug or injector; its wire, plug, injector and compression all test good, and the open companion wire explains both codes.

Standard reference: RSOS 2023 B-6.02.01L

At full load in Calgary, a diesel pickup's scan tool shows BARO 89 kPa and MAP 239 kPa absolute. The boost specification is 140–160 kPa (20–23 psi) gauge pressure. What gauge boost pressure do these readings show?

Answer: 150 kPa (about 22 psi) gauge: 239 − 89 = 150 kPa, which is inside the 140–160 kPa specification.

A MAP sensor reads absolute pressure, which includes the atmosphere; a boost spec in gauge pressure does not. Gauge = absolute − barometric: 239 kPa − 89 kPa = 150 kPa, and 150 × 0.145 = 21.8 psi. At Calgary's altitude BARO is well below the 101 kPa sea-level value, so subtracting 101 would wrongly show 138 kPa and an underboost.

Exam trap: 239 kPa, read straight from the MAP sensor: that is absolute pressure and looks like overboost; the 89 kPa barometric pressure must be subtracted first.

Standard reference: RSOS 2023 B-8.02.04P

A scan-tool data list is trimmed from 60 parameters to the 4 that relate to an intermittent fault. Why does this make a brief signal dropout more likely to be captured?

Answer: The tool requests each parameter in turn over the diagnostic link, so a shorter list refreshes every parameter more often.

Scan data is not continuous: the tool polls the module for each PID, and the link can carry only so many requests per second. With 60 PIDs, each may update only a few times per second, so a dropout lasting a fraction of a second can fall between samples. With 4 PIDs, each updates far more often. Events shorter than that still need a lab scope or graphing meter.

Exam trap: 'It just makes the screen easier to read': clarity helps, but the real gain is each parameter's faster update rate, which is what catches a short event.

Standard reference: RSOS 2023 C-10.02.02L

A TCM sets P0601 (internal control module memory checksum error) and holds the transmission in a fixed gear. The TCM still communicates with the scan tool, its power and grounds test good, and the manufacturer's site lists a current calibration for it. What is the correct next step?

Answer: Reprogram the TCM with the current calibration, then clear codes and retest; replace the TCM if P0601 sets again after a good reflash.

A memory checksum error means the stored software failed its integrity check, and a fresh download can correct it. The TCM still communicates, so it can accept the download, and its good power and grounds leave no supply fault to corrupt the new software. Unless the service information directs otherwise, the costly TCM is replaced only if P0601 returns after a good reflash.

Exam trap: Replacing the TCM because the code names an internal fault: the error is in its stored software, and a module that still communicates can usually be reflashed.

Standard reference: RSOS 2023 C-11.01.03P

In a RWD 5-speed manual transmission, 2nd gear power flows from a 22-tooth input gear to a 37-tooth countershaft drive gear, then from a 24-tooth countershaft 2nd gear to a 33-tooth mainshaft 2nd gear. What is the 2nd-gear ratio?

Answer: About 2.31:1: the input shaft turns 2.31 times for each turn of the output shaft.

Each mesh ratio is driven teeth ÷ driving teeth, and the meshes of a compound train multiply. Input to countershaft: 37 ÷ 22 = 1.682. Countershaft to mainshaft 2nd gear: 33 ÷ 24 = 1.375. Overall: 1.682 × 1.375 = 2.31:1 (1 221 ÷ 528), a speed reduction that multiplies torque about 2.3 times, less friction losses.

Exam trap: Adding the two mesh ratios (1.68 + 1.38 = 3.06:1): the ratios of meshes in series multiply, so adding them overstates the reduction.

Standard reference: RSOS 2023 D-12.02.01L

In a full-time AWD driveline that uses a viscous coupling between the front and rear drive, what determines how much torque the coupling transfers to the axle that still has grip?

Answer: The speed difference (slip) between its input and output plates: the more slip, the harder the silicone fluid is sheared and the more torque passes.

Alternate plates splined to the input and output run in silicone fluid, with no mechanical lock or actuator. With both sides at the same speed nothing shears and little torque passes. When one axle loses traction and spins faster, fluid shear between the plates drives the slower side; sustained heavy slip heats and stiffens the coupling toward lock-up (hump mode).

Exam trap: A driver switch or control-module command: a viscous coupling has no actuator and responds only to the slip between its two sides.

Standard reference: RSOS 2023 D-12.05.01L

A slipping cable-operated clutch is removed and its disc is oil-soaked. The rear main seal area and the engine side of the flywheel are dry and the engine oil level is steady, but the transaxle is 0.4 L low with no external leaks. What must be replaced along with the clutch?

Answer: The transaxle input-shaft seal, because the oil on the disc is transaxle fluid escaping past it, not engine oil.

A contaminated disc slips again unless the leak is fixed. Rear main seal oil wets the engine side of the flywheel first; that side is dry and the engine level is steady. A transaxle 0.4 L low with no external leak is losing fluid into the bellhousing, and its path there is past the input-shaft seal, so that seal is renewed with the clutch and the fluid level corrected.

Exam trap: The rear main seal: it is the usual suspect for an oily disc, but the engine side of the flywheel is dry and the engine oil level is not dropping.

Standard reference: RSOS 2023 D-13.04.03P

A V6 cranks slowly whether hot or cold. The battery passes a load test, cranking draw is 290 A against a 130–180 A spec, and both cable voltage drops are within OEM limits. With the spark plugs out, the crankshaft turns freely with a breaker bar. What is the most likely cause?

Answer: An internal starter motor fault, such as worn bushings letting the armature drag or shorted armature windings, drawing excess current.

A starter that draws high current yet turns slowly is either working against excess load or losing power internally. A good battery and in-limit cable drops clear the supply circuit, and a crankshaft that turns freely by hand with the plugs out rules out engine mechanical drag. That leaves the starter: a dragging armature or shorted windings raise current while cutting speed and torque.

Exam trap: Engine mechanical drag, such as a tight crankshaft or rod bearing: it would raise draw too, but the crankshaft turns freely with a breaker bar once the plugs are out.

Standard reference: RSOS 2023 E-14.02.07P

A pickup's trailer tail-lamp circuit, fused at 15 A by spec, kept blowing fuses, so a 30 A fuse was fitted; its 16 AWG feed in the hitch harness is now melted. With the trailer unplugged the circuit draws 0 A; plugged in, 22 A against 6 A for the trailer lamps. What repair is required?

Answer: Fix the trailer-side fault drawing the excess current, replace the melted section with 16 AWG wire and sealed splices, and refit the specified 15 A fuse.

A fuse is sized to protect the circuit's wire, not the load. The 15 A fuse was opening correctly because the trailer drew 22 A; the 30 A fuse let the 16 AWG wire overheat instead. Zero draw with the trailer unplugged clears the truck's wiring of any short, so the overload is in the trailer. All three faults must be corrected, then the draw re-checked with the trailer connected.

Exam trap: Replacing the melted wire and keeping the 30 A fuse because 15 A kept blowing: the trailer still draws 22 A, so the new wire would overheat the same way.

Standard reference: RSOS 2023 E-15.01.04P

With the A/C off, airflow is weak from every outlet in every mode and blower speed, in fresh air and recirculation alike. The blower wheel is tight on its shaft, and the motor sounds smooth but faster than normal while drawing below-spec current at each speed. What is the most likely cause?

Answer: A badly restricted cabin air filter starving the blower of air, so the fan unloads, speeds up and draws less current.

A centrifugal blower's load depends on how much air it moves. Restrict its inlet and airflow falls, so the motor unloads, speeds up and draws less current; a worn motor would slow down. Weak flow in fresh air and recirculation alike rules out the cowl intake and points to the cabin filter both pass through, and a tight wheel rules out slip. With the A/C off, an iced evaporator is ruled out.

Exam trap: A weak blower motor: a worn motor runs slower than normal, not faster, so it cannot explain high speed with low current.

Standard reference: RSOS 2023 E-16.01.09P

Why does selecting windshield defrost on most vehicles engage the A/C compressor and switch to outside air, even when full heat is requested?

Answer: To dry the air: the evaporator condenses moisture out before the heater core rewarms the air, and outside air is usually drier than humid cabin air.

Fog forms when humid cabin air meets cold glass. Air passing through the cold evaporator drops below its dew point and sheds water, then the heater core reheats it, giving warm, dry air that clears the glass quickly. Recirculated air keeps adding the occupants' breath moisture, so defrost forces fresh air. The compressor runs only when ambient temperature allows it.

Exam trap: To cool the defrost air and protect the glass from thermal shock: the heater core rewarms the air after the evaporator, so it still reaches the glass hot; the evaporator is there to remove water.

Standard reference: RSOS 2023 E-17.01.01L

A rack-and-pinion car has toe in spec, equal tie-rod lengths and a centred wheel. Turning-angle check: inside wheel at 20° gives an outside reading of 18.0° turning left and 19.6° turning right; spec is 18.0° ± 0.5°. What is the most likely cause?

Answer: A bent steering arm, which has altered the Ackermann (toe-out-on-turns) geometry.

Ackermann geometry, set by the steering-arm angles, makes the inside wheel turn more than the outside one. With the inside wheel at 20°, the outside should read 18.0° ± 0.5°, so at most 18.5°. Toe, tie-rod lengths and centring are correct, yet turning right reads 19.6°, 1.1° past that limit, so a steering arm is bent and must be replaced; it cannot be adjusted out.

Exam trap: An off-centre rack from unequal tie-rod adjustment: it can skew turning angles one way, but the tie rods are equal and the wheel is centred, so the rack is centred.

Standard reference: RSOS 2023 F-18.01.07L

After four new tires were installed, a car drifts right on a level road. Alignment, tire pressures and brake drag checks are all within spec. With the two front tires swapped side to side, the car now drifts left. What is the cause?

Answer: Conicity (radial tire pull) in one of the front tires; the side force moves with the tire, so the drift reverses.

A tire with conicity, often from an off-centre belt, rolls like a cone and produces a steady side force regardless of alignment. Swapping the fronts side to side reverses that force, so a drift that changes direction after the swap comes from a tire, not the chassis. Find the faulty tire by swapping each front with a rear, then move it to the rear or replace it.

Exam trap: Cross-caster or cross-camber error: alignment is in spec, and alignment angles do not change when tires are swapped, so the drift would have stayed to the right.

Standard reference: RSOS 2023 F-18.03.07P

A power-steering system whines and steers heavily two weeks after its replacement pump was fitted without a flush. The pump inlet and reservoir screen are packed with fine metal from the original pump's failure. At installation, the gear held full pressure at both locks. What repair is required?

Answer: Replace the reservoir and screen, flush the gear, lines and cooler, fit an inline return-line filter, then install another new pump with the specified fluid.

A failed pump spreads metal through the gear, lines, cooler and reservoir. Unflushed, it circulated, packed the screen and starved and wore the new pump. The gear held full lock pressure at installation, so it is flushed rather than replaced, and a return-line filter traps what remains. Afterwards recheck lock pressure, and replace the gear only if it fails that test or the OEM requires it.

Exam trap: Fitting another pump only: metal left in the gear, lines, cooler and reservoir screen would wear it out the same way; the contamination, not the pump, is the root cause.

Standard reference: RSOS 2023 F-19.01.03P

A car with indirect TPMS (no pressure sensors; it compares ABS wheel speeds) has just had its tires rotated and its pressures adjusted. What must be done so the system will warn correctly?

Answer: Set all four tires to placard pressure cold, then run the TPMS reset (initialization) so it relearns the wheel-speed baseline at those pressures.

An indirect system detects a low tire because it rolls on a smaller radius and turns faster than the others. It learns each wheel's normal rolling behaviour after a reset, so the reset must follow correct cold pressures; resetting with a tire low teaches the system that the low tire is normal. Learning then completes during the following drive.

Exam trap: Performing a sensor-ID relearn with a TPMS trigger tool: an indirect system has no wheel sensors to register; it needs only the baseline reset.

Standard reference: RSOS 2023 F-19.03.05P

A crossover's doors close hard with all windows up but easily with one window open. At highway speed with the fan on high in fresh-air mode, a whistle comes from the upper door seals. The rear bumper cover was replaced last month. What is the most likely cause?

Answer: Blocked or stuck body air extractors (pressure-relief vents) behind the rear bumper cover, so cabin air cannot escape.

Air entering through the HVAC inlet leaves through one-way extractor vents, usually in the rear quarters behind the bumper cover. If they are blocked or their flaps stick, cabin pressure rises: doors resist closing and air forces its way out past the door seals, whistling at speed with the fan on high. An open window relieves the pressure, which a seal or alignment fault would not explain.

Exam trap: Misaligned doors or worn seals: neither would close easily with a window open, and neither depends on fan speed and fresh-air mode.

Standard reference: RSOS 2023 G-20.02.01L

A 12-year-old car's front door whistles at speed near its upper rear corner. Paper closed in the door pulls out with almost no drag along the whole top of the frame. Gaps, flushness (upper frame included) and striker engagement are correct; the seal and glass are fully seated. What is the repair?

Answer: Replace the door-frame weatherstrip; it has taken a compression set and no longer seals against the body.

A drag test checks seal contact: paper closed in the door should pull out with steady resistance all round. Almost no drag along the whole top, with the door and its upper frame correctly aligned and the seal and glass fully seated, leaves the seal itself: after 12 years it has taken a compression set and no longer springs back against the body, so only a new weatherstrip restores contact.

Exam trap: Moving the striker inward to squeeze the seal: the door is already aligned, so this misaligns it, raises closing effort and barely compresses a dead seal.

Standard reference: RSOS 2023 G-21.02.03P

During hot-weather DC fast charging, an EV limits power for high battery temperature. Cabin A/C is normal and the battery coolant pump holds commanded speed, but commanding battery chilling on changes neither suction pressure nor chiller coolant outlet temperature. What is the most likely fault?

Answer: The chiller's electronic refrigerant control (expansion) valve is stuck closed or not responding, so no refrigerant cools the battery coolant.

The chiller is a refrigerant-to-coolant heat exchanger fed through its own electronic valve. Commanding battery chilling opens that valve, which should shift suction pressure and drop the coolant outlet temperature. Normal cabin cooling proves the compressor and charge, and the pump holding speed shows coolant flow, so no response isolates the chiller valve or its control circuit.

Exam trap: A low refrigerant charge or failed battery coolant pump; cabin cooling is normal and the pump holds commanded speed, leaving only the chiller valve unresponsive.

Standard reference: RSOS 2023 H-22.04.08P

10 pairs · 1 decoyChecked at the end