Recreation Vehicle Service Technician Flashcard Match
Online Red Seal Exam Preparation, built on official standardsSet up a round
Cards from
Pairs per round
Blocks
Decoys
240 cards to draw from
Your rounds
Kept on this device- 80%10 pairs · 4:12TodayRetry the wrong ones
- 70%10 pairs · 4:40TodayRetry the wrong ones
- 87%15 pairs · 6:05YesterdayRetry the wrong ones
- 100%10 pairs · 3:3111 NovPlay again
- 60%5 pairs · 2:2010 NovRetry the wrong ones
Checking
What a checked pair looks likeChecking
Clock
How a round works
Each card is the front of a flashcard from the set you chose.
Drag it onto its answer, or tap the card and then the answer. Every miss shows the right pair and the why behind it.
Browse the 20 free cards and explanations
Metal swarf packs a cordless drill chuck after RV sheet-metal work. How should the chuck be cleaned without hand contact with chips or unintended rotation?
Answer: Remove the battery and clear the swarf with a suitable brush under the tool cleaning procedure.
Removing the energy source prevents accidental rotation while a brush separates the hands from sharp swarf. Tool cleaning should not rely on holding a rotating chuck or grasping chips.
Exam trap: Squeezing the trigger to fling swarf out creates moving-tool and flying-chip hazards instead of controlled cleaning.
Standard reference: RSOS 2022 A-2.01.02P
During PDI, 12 V loads work on shore power but not on battery power. The battery passes its specified load test and the distribution fuses are intact. Which supply path should be checked next?
Answer: The battery-to-distribution path, including its disconnect switch and connections.
Shore power proves the loads can operate, and the battery load test removes a failed battery as the leading explanation. The unverified link is the path that connects that battery to the distribution system.
Exam trap: Signing off because the converter runs the loads leaves battery-only operation unverified.
Standard reference: RSOS 2022 A-3.03.01P
A vented fresh-water tank draws inward as the pump runs. The pickup is clear, and flow returns when the tank's vent path is temporarily opened for testing. What fault is indicated?
Answer: A restricted fresh-water tank vent.
Water removed from a vented tank must be replaced by air. Tank deformation and restored flow when the vent path is opened show that vacuum, rather than a blocked pickup, limits delivery.
Exam trap: A worn pump does not explain why opening the tank vent restores flow and stops the tank drawing inward.
Standard reference: RSOS 2022 B-5.01.03P
After de-winterizing an RV, the main faucets run clear, but an isolated exterior sprayer still contains plumbing antifreeze. What maintenance remains before returning the system to use?
Answer: Open and flush the sprayer's isolated branch under the approved de-winterizing procedure.
Flow through the main distribution lines does not flush a closed branch. Each retained section must be included so the complete potable system is restored.
Exam trap: Running the kitchen tap longer cannot flush a branch that remains shut off.
Standard reference: RSOS 2022 B-6.01.06P
A grey-tank side fitting has been repaired. Its instructions call for a water leak test to above the repaired connection. What must be verified before the access panel is refitted?
Answer: That the repaired connection remains dry at the specified test water level.
Brief flow past a fitting may not load the seal as a filled tank does. Testing to the specified level with access open verifies the repair under the required static head.
Exam trap: A quick drain-flow check alone may never raise water to the repaired connection.
Standard reference: RSOS 2022 B-7.02.05P
An RV inverter supplies a non-sinusoidal AC waveform. Which voltage-meter capability is needed to measure its RMS output accurately within the instrument’s waveform limits?
Answer: True-RMS measurement with suitable bandwidth and crest-factor limits for that waveform.
An average-responding meter calibrated for sine waves can misreport a distorted waveform. A suitable true-RMS instrument measures its effective voltage within its stated frequency and waveform limits.
Exam trap: A meter that reads accurately on sinusoidal shore power is not necessarily accurate on this inverter waveform.
Standard reference: RSOS 2022 C-8.01.02P
Dust has blocked an inverter cooling grille. After all sources are isolated and stored energy handled as directed, what maintenance restores the intended cooling path?
Answer: Remove dust using the approved method and restore the specified unobstructed ventilation clearance.
Cooling requires both a clear grille and open space for airflow. Cleaning alone cannot restore heat rejection if nearby stored items continue to block discharge.
Exam trap: Adding a larger output breaker cannot improve airflow and may defeat circuit protection.
Standard reference: RSOS 2022 C-9.01.04P
A new RV receptacle requires a bonding conductor connection. The metal box is bonded already. How should the device bonding terminal be treated?
Answer: Connect it using the approved bonding arrangement for that box and device.
The device needs its intended fault-current path. A bonded box alone does not establish that an arbitrary mounting arrangement provides the required device bond.
Exam trap: Assuming any mounting screw provides an approved bond skips verification of the actual box and device arrangement.
Standard reference: RSOS 2022 C-9.03.04P
An RV accessory draws 4 A for 3 h and then 0.2 A in standby for 5 h. Ignoring conversion losses, what daily charge use belongs in its battery-capacity calculation?
Answer: 13 Ah.
Active use is 4 × 3 = 12 Ah; standby is 0.2 × 5 = 1 Ah. Total use is 13 Ah before allowances for usable capacity and losses.
Exam trap: 12 Ah omits the five hours of standby current.
Standard reference: RSOS 2022 C-10.03.02P
A high-pressure propane fitting must be checked with leak-detection fluid. How should the fluid be selected?
Answer: Use a product approved for propane leak detection and compatible with the fitting materials.
Leak fluid must reveal escaping gas without attacking the assembly. Suitability for the gas and materials matters; an arbitrary household mixture is not an approved substitute.
Exam trap: Choosing any foaming detergent ignores additives that may be unsuitable for the component materials.
Standard reference: RSOS 2022 D-12.01.05P
An appliance manual specifies inlet pressure while the burner operates. Where should the pressure instrument be connected to verify that value?
Answer: At the specified appliance inlet test point, following its connection and operating procedure.
The stated specification applies at the appliance inlet under flow. A reading elsewhere may not include the pressure loss through the intervening supply path.
Exam trap: A pressure reading upstream at the regulator cannot by itself establish the value at the appliance inlet.
Standard reference: RSOS 2022 D-12.02.04P
A failed two-stage RV regulator is rated for propane vapour. A replacement has enough flow capacity and matching threads, but its data specify liquid withdrawal. Is it an acceptable substitute?
Answer: No. Obtain the approved vapour-service regulator with the required ratings and configuration.
Capacity and thread fit do not overcome a mismatch in the supplied fuel phase. The replacement must suit the actual vapour system as well as its pressure and flow requirements.
Exam trap: Selecting by capacity alone ignores the explicit liquid-versus-vapour service mismatch.
Standard reference: RSOS 2022 D-13.02.03P
An oven test procedure uses the mean of stabilized cycle minimum and maximum temperatures. They are 168 °C and 188 °C at a 180 °C setting. What temperature error should be recorded?
Answer: The cycle mean is 178 °C, or 2 °C below the setting.
The specified mean is (168 + 188)/2 = 178 °C. Subtracting the 180 °C setting gives -2 °C; acceptance depends on the stated service tolerance.
Exam trap: Calling it 8 °C too hot uses only the cycle maximum instead of the required mean.
Standard reference: RSOS 2022 E-14.03.06P
After a furnace blower motor replacement, its wheel rubs the housing when turned by hand. The shaft and wheel are undamaged. What should be corrected before applying power?
Answer: Correct the wheel positioning and alignment, then verify specified clearances and free rotation.
A replacement blower wheel must clear its housing throughout a full rotation. Correct its position and alignment before applying power; an undamaged housing does not establish correct assembly.
Exam trap: Running the blower to wear away the contact can damage the wheel or motor and does not correct its positioning.
Standard reference: RSOS 2022 E-16.02.08P
An absorption refrigerator’s exterior vents match its installation drawing. Its burner operates normally, but gaps in the specified enclosure seal connect the rear combustion compartment to the cabin. What must be corrected before release?
Answer: Restore the specified separation seal between the rear compartment and the cabin.
Correct vent layout and normal flame operation do not close an unintended path into occupied space. The enclosure boundary must meet the installation design independently of burner performance.
Exam trap: A normal flame observation cannot establish that combustion products are isolated from the cabin.
Standard reference: RSOS 2022 E-18.03.05P
An interior drawer binds after a cabinet repair. Before adjusting the slides, how should the cabinet opening be checked for squareness?
Answer: Measure and compare its two corner-to-corner diagonals.
For an intended rectangular opening, unequal diagonals indicate that it is out of square. Checking the opening prevents slide adjustments from concealing a cabinet geometry problem.
Exam trap: Measuring only the opening width does not reveal racking; the top and bottom can have equal widths while the diagonals differ.
Standard reference: RSOS 2022 F-21.01.02L
An exterior hatch binds only as its latch enters the striker. The hatch is square, hinges are tight, and the latch leaves a fresh witness mark above the striker opening. What maintenance adjustment is indicated?
Answer: Align the striker with the latch travel.
The hatch geometry and hinges are sound; interference occurs at a documented latch-to-striker mismatch. Correct alignment allows closure without forcing the hatch out of position.
Exam trap: Adjusting the hinges would disturb the verified hatch alignment while leaving the actual latch interference unresolved.
Standard reference: RSOS 2022 F-23.01.04P
A hydraulic levelling jack has an effective piston area of 0.002 m² and measured pressure of 6 MPa. Using force = pressure × area and ignoring friction, what extension force is available?
Answer: 12 000 N, or 12 kN.
Convert pressure to pascals: 6 MPa = 6 000 000 Pa. Force = 6 000 000 × 0.002 = 12 000 N. This is the ideal force under the stated pressure and effective area, before losses.
Exam trap: Multiplying 6 by 0.002 without converting MPa to Pa gives the wrong force units and magnitude.
Standard reference: RSOS 2022 G-24.03.01L
An automatic levelling control has been replaced. Before storing its level reference, how must the RV’s position be established?
Answer: Set the RV to the manufacturer’s specified level reference using an independent level at the designated datum.
Calibration teaches the control which position represents level. An independent reference at the specified location prevents an incorrect attitude from being stored as the target.
Exam trap: Using the uncalibrated display to establish its own reference is circular and can store an incorrect level.
Standard reference: RSOS 2022 G-27.02.07P
A tow-bar manual permits no more than 75 mm vertical difference between its attachment points. Measurements are 520 mm and 625 mm. What does the setup require?
Answer: Correct the 105 mm height difference with an approved arrangement before towing.
The difference is 625 - 520 = 105 mm, which exceeds the stated 75 mm limit by 30 mm. The installation must meet the specified geometry and component ratings.
Exam trap: Accepting it because the arms connect ignores the manufacturer’s permitted operating angle.
Standard reference: RSOS 2022 H-30.02.08P