Gasfitter – Class B Flashcard Match
Online Red Seal Exam Preparation, built on official standardsSet up a round
Cards from
Pairs per round
Blocks
Decoys
200 cards to draw from
Your rounds
Kept on this device- 80%10 pairs · 4:12TodayRetry the wrong ones
- 70%10 pairs · 4:40TodayRetry the wrong ones
- 87%15 pairs · 6:05YesterdayRetry the wrong ones
- 100%10 pairs · 3:3111 NovPlay again
- 60%5 pairs · 2:2010 NovRetry the wrong ones
Checking
What a checked pair looks likeChecking
Clock
How a round works
Each card is the front of a flashcard from the set you chose.
Drag it onto its answer, or tap the card and then the answer. Every miss shows the right pair and the why behind it.
Browse the 20 free cards and explanations
A meter shows 0.2 Ω through a lead held still, but OL whenever that lead is flexed near its plug. A second lead stays at 0.2 Ω on the same meter jacks. What defect best explains this?
Answer: An intermittent internal break in the first test lead near its plug.
Flexing changes only the suspect lead and repeatedly opens its circuit. A stable second lead on the same jacks points to the first lead rather than the meter. Remove the defective lead from service.
Exam trap: Meter zero error would not repeatedly become an open circuit only when one lead is flexed.
Standard reference: RSOS 2024 A-2.02.02P
A cantilever pipe bracket carries a 240 N load 0.25 m from its wall fixing. Its rated bending moment is 50 N·m. Is it suitable for this load position?
Answer: No; the 60 N·m bending moment exceeds its 50 N·m rating.
A cantilever load produces moment equal to force × perpendicular lever arm. Here 240 × 0.25 = 60 N·m. Selection must meet the support rating for the actual geometry.
Exam trap: Comparing only the 240 N force ignores the increased demand created by the projecting arm.
Standard reference: RSOS 2024 B-5.01.03P
An IPEX VA service saddle has a straight-thread female outlet. A tapered pipe nipple is available and seems to start into it. Should that nipple be used?
Answer: No; use the manufacturer-approved straight-thread outlet connection.
Starting into the outlet does not establish a compatible sealing connection. The VA saddle instructions identify a straight-thread outlet and prohibit tapered fittings there.
Exam trap: Forcing a tapered nipple tighter does not convert the saddle outlet into a tapered-thread joint.
Standard reference: RSOS 2024 B-5.03.02P
Using the XR3 REV2 utility-knife preparation method, to which corrugation reference is the jacket stripped back from the CSST cut end?
Answer: To the second valley from the tubing end, exposing one full corrugation valley.
The manufacturer defines this stripping reference to expose the end required for the fitting while retaining the jacket beyond it. Knife pressure must not score the underlying stainless tubing.
Exam trap: Stripping several extra valleys unnecessarily exposes tubing and is not the prescribed preparation.
Standard reference: RSOS 2024 B-6.02.02L
One sealed System 636 cement can is thick after freezing and returns to normal when warmed. A second can has lost solvent and remains gelled when warm. Which can must be discarded?
Answer: Discard the can that remains gelled after solvent loss.
Freezing can temporarily thicken the cement, with normal consistency returning on warming. Solvent-loss gel does not recover and must not be restored by adding thinner or primer.
Exam trap: Discarding both solely because they were thick ignores the reversible cold-thickening evidence.
Standard reference: RSOS 2024 C-7.02.03L
A proposed appliance air-intake location is directly beside an outdoor swimming-pool chemical store. Its opening is clear of snow and debris. What siting issue still requires relocating the intake?
Answer: The intake can draw corrosive chemical vapours from the nearby store.
Air-source quality matters as well as an unobstructed opening. Chlorine-bearing pool chemicals can contaminate combustion air and damage equipment; a clean-source location is required.
Exam trap: A debris screen stops solids but does not remove chemical vapours.
Standard reference: RSOS 2024 C-8.01.01P
A spare opening below the appliance flue entry is available in a chimney. May a Field MG1 be installed there to avoid modifying the connector?
Answer: No; the MG1 must not be installed in the chimney below the flue entry.
The manufacturer explicitly excludes that location. A convenient unused opening does not establish an acceptable draft-control connection for the appliance.
Exam trap: Using an existing opening saves fabrication but violates the stated installation restriction.
Standard reference: RSOS 2024 C-9.01.01P
Why must a fuel-air ratio controller retain the appliance’s independent safety interlocks when its modulation is configured?
Answer: Ratio modulation does not replace the independent permissives and shutdown functions that prevent unsafe fuel admission.
Combustion modulation positions fuel and air to meet demand. A correct ratio command alone cannot establish that flame, draft or other required safety conditions permit fuel admission.
Exam trap: A correct fuel-air ratio makes the safety chain unnecessary. Modulation does not prove every required safety condition.
Standard reference: RSOS 2024 D-10.02.01L
An inducer produces the specified negative gauge pressure at the sensing port. Tubing is clear, but a proposed switch closes only on positive pressure and has no approved reverse connection. What selection correction follows?
Answer: Select the specified negative-pressure switch with the required operating action and set point.
The port pressure and clear tubing support the intended draft signal. A positive-pressure-only switch cannot provide the required proof simply by changing its set point or improvising its connections.
Exam trap: Raise the inducer speed until that switch closes. This changes the appliance operating condition to accommodate an incompatible control.
Standard reference: RSOS 2024 D-12.01.02P
A furnace’s PSC blower requires a 5 µF continuous-duty run capacitor rated at least 370 V AC. Available replacements are 5 µF/440 V AC and 7.5 µF/370 V AC, both run-rated. Which is suitable?
Answer: The 5 µF, 440 V AC run capacitor.
The specified capacitance governs the motor’s phase-shifting circuit; voltage rating must meet or exceed the requirement. The 5 µF unit preserves capacitance and has an adequate voltage rating.
Exam trap: Use 7.5 µF to improve starting. Increasing capacitance changes the specified motor circuit and can increase winding stress.
Standard reference: RSOS 2024 D-13.01.02P
A gas-train regulator must supply 60 kW. Its chart gives 80 kW at 5 kPa inlet but 45 kW at the site’s minimum 3 kPa inlet, both at the required outlet pressure. Which capacity governs selection?
Answer: The 45 kW capacity at the minimum 3 kPa inlet; this regulator is insufficient for the 60 kW duty.
Regulating capacity depends on the available pressure conditions. Selecting from the higher-inlet row would overstate delivery during minimum supply pressure, when the full appliance duty still has to be met.
Exam trap: Use the 80 kW figure from the chart’s higher inlet pressure. That pressure is not assured at the site.
Standard reference: RSOS 2024 E-15.01.04P
In a nozzle-mix conversion burner, where are separately supplied fuel and combustion air brought together, unlike an upstream premix arrangement?
Answer: At the burner discharge and combustion zone, rather than in an upstream premix passage.
Nozzle-mix burner streams meet where the burner discharges into its combustion region. The fuel and air are not delivered as a combustible premixed stream through the upstream mixer and passage.
Exam trap: In the fuel-supply manifold before the burner. That describes an upstream mixing arrangement, not the nozzle-mix operating principle.
Standard reference: RSOS 2024 E-15.03.01L
A newly connected propane cylinder is labelled for upright vapour withdrawal but is mounted inverted. Idle pressure looks normal, then liquid reaches the vapour regulator during demand. What installation defect must be corrected?
Answer: Restore the cylinder’s approved upright orientation and vapour-withdrawal connection before further operation.
Idle pressure does not identify the phase delivered under flow. Inversion can bring liquid to a connection intended to withdraw vapour; the cylinder must be installed in its approved operating orientation.
Exam trap: Reduce the regulator setting because idle pressure is normal. A pressure adjustment does not correct liquid entering a vapour system.
Standard reference: RSOS 2024 E-16.02.07P
A methane leak detector needs 5 s at each joint for its specified response. A sweep takes 1 s per joint and shows zero. How should the joints be checked before recording the result?
Answer: Resample each joint for the required response time using the detector procedure.
The sensor needs time to respond to gas at the sampling location. A sweep shorter than the stated response time can miss a leak even when the instrument functions correctly.
Exam trap: Increasing alarm sensitivity does not replace sufficient sampling time at each joint.
Standard reference: RSOS 2024 F-18.01.01P
A new blower is ready for its approved start test. A spare shaft key remains loose on its unused shaft extension. What preparation is required before energizing it?
Answer: Remove the unsecured shaft key before the start test.
An unsecured key on an unused rotating shaft can be thrown from the shaft. Remove loose rotating parts while isolated before the approved start test.
Exam trap: A correct rotation arrow does not restrain a loose shaft key.
Standard reference: RSOS 2024 F-19.01.01L
A handover report records acceptable combustion readings but omits the analyser’s selected fuel. Why must that fuel setting be added to the report?
Answer: It identifies the fuel basis used for the analyser’s calculated combustion results.
Calculated values such as CO2 and efficiency depend on the selected fuel model. Recording the fuel makes those results interpretable and reproducible.
Exam trap: The appliance model number does not establish which fuel setting the analyser actually used.
Standard reference: RSOS 2024 F-19.03.01P
During inspection, a normally closed gas safety valve is de-energized. Its approved seat test shows continuing downstream pressure build-up after the specified bleed step. What part of the valve’s operation fails?
Answer: Tight shutoff at the valve seat.
The prescribed bleed removes trapped downstream pressure. Continued rebuild with the valve de-energized indicates fuel passing the closed seat under the defined test conditions.
Exam trap: An electrically unpowered coil does not itself prove that the valve seals mechanically.
Standard reference: RSOS 2024 G-20.01.17P
A blower wheel carries uneven deposits on its blades. Its specified maintenance is cleaning, with the original balancing features retained. Which parts of the rotating assembly should be cleaned?
Answer: Clean deposits from all specified blade surfaces while preserving the wheel’s balance features.
Uneven deposits alter airflow and rotating mass distribution. Cleaning only accessible blades leaves an unequal deposit pattern; the original balance features must remain intact.
Exam trap: Removing balance weights to make cleaning easier changes the designed balance rather than removing deposits.
Standard reference: RSOS 2024 G-20.02.03P
A replacement gas valve permits 10 mm maximum pipe insertion. Its new pipe end enters 14 mm before the joint tightens. What preparation is needed before installing the valve?
Answer: Remake the pipe end to achieve the specified joint engagement without exceeding the valve’s insertion limit.
Excessive insertion can interfere with internal parts or distort a valve body. Thread fit and apparent tightness do not establish safe engagement with the valve’s internal geometry.
Exam trap: Adding tightening torque drives the already excessive engagement farther into the valve.
Standard reference: RSOS 2024 G-21.02.09P
A repaired blower’s speed pickup produces three pulses per shaft revolution. A verified frequency counter reads 120 Hz at steady operation. What shaft speed should the verification record?
Answer: 2,400 r/min.
120 Hz means 120 pulses per second. Divide by three pulses per revolution to get 40 revolutions per second, then multiply by 60: 2,400 r/min. The pickup’s pulse count must be included when converting frequency to speed.
Exam trap: Record 7,200 r/min by multiplying frequency by 60 alone. That incorrectly assumes one pulse per revolution.
Standard reference: RSOS 2024 G-21.03.05P