Pass Your Red Seal

Ironworker (Reinforcing) Flashcard Match

Online Red Seal Exam Preparation, built on official standards
Flashcard Match10 pairs · 1 decoyChecked at the endStart matching

Set up a round

Cards from

Pairs per round

Blocks

Decoys

240 cards to draw from

ACommon occupational skills58
BRigging, hoisting and positioning, and participates in crane and equipment mobilization and demobilization56
CFabricates and installs reinforcing materials98
DPre-stressing/post-tensioning28

Your rounds

Kept on this device
Average79%
Best100%

Checking

What a checked pair looks like
Browse the 20 free cards and explanations

Holes for drilled-in dowels must be made in a cured concrete wall with a rotary hammer. Which hazardous dust is the main concern, and which level of the hierarchy of controls is applied first?

Answer: Respirable crystalline silica; engineering controls come first: an on-tool shroud with a HEPA extractor, or water at the bit, with respirators as backup.

Concrete contains crystalline silica, and drilling releases fine respirable particles that cause silicosis and lung cancer. The task and tool are fixed, so elimination and substitution are not available and the first control is engineering: capture or suppress the dust at the bit. Respirators are the least effective control and are added as the exposure control plan directs.

Exam trap: A respirator alone: PPE is the last line of defence and is used with source controls such as on-tool extraction or water, not instead of them.

Standard reference: RSOS 2025 A-1.01.12P

A powder-actuated tool will fasten a support bracket to existing concrete of unknown strength. Which power level is used for the first test fastening?

Answer: The lowest-power load recommended for the tool, stepping up one level at a time only if the fastener doesn't set properly.

Too much power can overdrive the fastener, spall the concrete or cause a ricochet. CCOHS and tool manufacturers call for a trial with the weakest charge first, increasing one level at a time until penetration is correct. Only trained, authorized operators use these tools, following the jurisdiction's rules.

Exam trap: A mid-range load to avoid wasting cartridges: an overpowered first shot can overdrive the fastener, spall the base or ricochet.

Standard reference: RSOS 2025 A-2.02.01P; A-2.02.02L (a)

A tall column cage is being plumbed before its forms are closed, and every reading so far has been taken on the same face. Why is that not enough?

Answer: One face shows lean in only one direction; the cage can still lean at right angles to it, so an adjacent face 90° around must also be checked.

A level, transit or plumb bob checks verticality in only one vertical plane, so a lean along the other horizontal axis is invisible from that side. Checking a second face 90° away covers both directions and confirms the cage is plumb before the forms close.

Exam trap: Taking more readings, higher and lower, on the same face: extra readings in the same plane still cannot show a lean in the perpendicular direction.

Standard reference: RSOS 2025 A-2.08.05P; A-2.08.02L (f)

A delivered bundle tagged with bar mark W12 contains 20M bars, but the approved bar list shows W12 as 25M. The rest of the load matches. What is done with this bundle?

Answer: Set it aside unused, note the discrepancy on the delivery paperwork and report it so the fabricator supplies the correct 25M bars.

Delivered material is checked against the shipping documents and bar list before it is accepted. Bars smaller than detailed reduce the steel area the engineer designed for, so the bundle is segregated, recorded on the delivery ticket and reported; it is not placed.

Exam trap: Placing the 20M bars at closer spacing to make up the area: any substitution is a design change that only the engineer can approve.

Standard reference: RSOS 2025 A-3.01.01P

A rebar delivery on the project's critical path arrives 2 days late, and no recovery is planned. What happens to the project completion date?

Answer: It moves 2 days later, because activities on the critical path have no float.

The critical path is the longest chain of dependent activities, and its activities have zero total float. Any delay to them delays completion by the same amount unless later critical work is shortened or resequenced. Activities off the critical path can absorb delays up to their float.

Exam trap: No change, because the crew can work faster later: that is recovery, which the scenario rules out; without it the full 2 days carry to completion.

Standard reference: RSOS 2025 A-3.04.01L (g)

Site procedure classes any lift over 75% of chart capacity as critical. A 3 400 kg bundle will be lifted with a 250 kg spreader and slings on a 150 kg hook block, where the chart allows 4 800 kg. How is the lift classed?

Answer: As a critical lift: the gross load of 3 800 kg is about 79% of the 4 800 kg chart capacity.

Everything the crane carries counts against chart capacity: 3 400 + 250 + 150 = 3 800 kg. Then 3 800 ÷ 4 800 = 0.79, or 79%, which is above the site's 75% threshold, so the site's critical-lift requirements apply, such as a written critical lift plan and its approvals.

Exam trap: A routine lift at 71% (3 400 ÷ 4 800); that leaves out the spreader, slings and hook block, which the crane lifts along with the bundle.

Standard reference: RSOS 2025 B-6.02.02P

A wire rope choker shows 3 broken wires in one rope lay, under the company limit of 6 per lay. At the same spot, where it was choked on a bundle, two strands are crushed flat. Can the sling stay in service?

Answer: No. Crushing distorts the rope structure, and distortion removes the sling from service regardless of the broken-wire count.

Removal criteria are independent: meeting any one retires the sling. The broken-wire count is below the limit, but crushed, flattened strands no longer share load evenly and can hide internal damage. Distortion such as crushing, kinking or bird caging is a removal criterion on its own.

Exam trap: Keeping it because broken wires are under the limit; that judges the rope on one criterion and ignores the crushing found at the same location.

Standard reference: RSOS 2025 B-7.01.02L (c); B-7.01.03P

A delivered bundle of 15M bars is held together by several twisted wire ties. What may the slings be attached to when the bundle is hoisted?

Answer: Only around the bars themselves, with rated slings round the whole bundle; the bundle ties are never used as lifting points.

Bundle ties and bands only keep the bars together for handling and are not rated for any lifting load; they can untwist or snap and drop the bars. Rated slings must carry the load directly around the steel, at the pick points the rigging plan sets.

Exam trap: Hooking or shackling under the bundle ties because they look strong; ties have no rated capacity and fail suddenly.

Standard reference: RSOS 2025 B-7.03.02L (j)

After a mat is landed, the post-lift inspection finds epoxy coating scraped off several bars already placed in the deck. What is done about this damage?

Answer: It is assessed, tagged and reported to supervision so it can be repaired to project requirements before concrete is placed.

Damage to installed equipment and materials found after a lift is assessed, tagged and reported to supervision according to company procedures. Bare spots on coated bars defeat the corrosion protection, so they must be found and repaired as specified, not buried by the pour.

Exam trap: Leaving it because the bars are already tied in place; once concrete is placed the damage can no longer be found or repaired.

Standard reference: RSOS 2025 B-8.01.03P

A crane's whipline is rigged with a single part of line and a headache ball instead of a block. What does the ball's weight do when no load is on the hook?

Answer: It overhauls the single-part line, pulling the rope down off the drum and keeping it taut so it pays out and spools properly.

An overhaul (headache) ball is a weight on a single-part line. Without it, the light hook could not pull the rope down from the boom tip, and slack rope would spool badly on the drum. The ball's weight keeps the line under tension as it pays out.

Exam trap: It adds lifting capacity to the whipline; the ball is dead weight that counts against the capacity, not something that adds to it.

Standard reference: RSOS 2025 B-9.01.01L (b)

Glass fibre-reinforced polymer (GFRP) composite bars must be shortened on site. Which cutting method is correct?

Answer: Saw them with a fine-tooth, carborundum or diamond blade (or a grinder); never cut GFRP with shears.

Shearing crushes the resin and splits the glass fibres rather than making a clean cut. Use the bar manufacturer’s approved saw or abrasive cutting equipment. Canadian GFRP manufacturer instructions distinguish these cutting methods from shear cutting, which is prohibited.

Exam trap: A hydraulic rebar shear, as used on black bar. It crushes and splits the fibres instead of cutting them cleanly.

Standard reference: RSOS 2025 C-10.01.02L (d)

According to the Red Seal formula sheet, what minimum bending pin diameter applies to uncoated 30M and 35M bars?

Answer: Eight bar diameters (the sheet's 8D).

The formula sheet sets the bending pin for uncoated bar at 6 bar diameters for sizes up to 25M and 8 bar diameters for sizes larger than 25M. The larger multiplier for big bars limits the risk of cracking the bar at the bend and of crushing the concrete inside it.

Exam trap: Six bar diameters (6D) for every size. That multiplier stops at 25M; 30M and 35M bars step up to 8D.

Standard reference: RSOS 2025 C-10.02.03P

A 1.5 m thick raft footing needs its top mat held about 1.3 m above the bottom mat, well beyond the height of commercial chairs. What is normally used to support that top mat?

Answer: Standees: support assemblies fabricated from reinforcing bar, sized, spaced and braced as shown on the placing drawings.

Commercial wire, plastic or precast chairs suit thinner sections; thick footings and mats use standees bent from rebar. Their spacing must carry the dead load of the top mat and the workers on it, and bracing must resist sideways loads, so they are placed exactly as detailed.

Exam trap: Stacked concrete blocks or high chairs: stacks topple and chairs are not made this tall, and neither is designed to carry a heavy top mat 1.3 m up.

Standard reference: RSOS 2025 C-11.01.06P; C-11.01.01L (b)

One GFRP bar is dropped from the truck deck and another is hammered into position in the mat. Neither shows a crack. May they be installed solely because they pass a visual check?

Answer: No. Segregate both and report the impacts for disposition under the supplier’s and engineer’s requirements before either is installed.

Impact can damage a composite bar’s resin or load-carrying fibres, and a clean-looking surface does not establish retained strength. The handling incident must be assessed; the placer does not approve questionable material by eye or assume that steel-bar handling methods apply to GFRP.

Exam trap: Installing them because no crack is visible: appearance alone cannot resolve possible internal damage from the impacts.

Standard reference: RSOS 2025 C-11.01.05P; C-11.01.01L (a)

Thousands of intersections in a flat slab mat must be tied quickly, and the bars lie flat with light demands on each tie. Which wire tie is normally used?

Answer: The snap tie.

A snap tie makes a single diagonal loop around the crossing and is twisted tight. It is quick to form and suits these flat, lightly loaded intersections, where the main purpose is to keep the bars in position until concrete is placed.

Exam trap: The saddle tie: it grips harder but takes longer to make, extra holding that flat, lightly loaded slab intersections do not need.

Standard reference: RSOS 2025 C-11.02.01L (a)

Thousands of slab intersections are hand-tied each day with pliers and reel wire. Which tool removes most of the repetitive hand and wrist motion that leads to musculoskeletal injury?

Answer: A battery-powered rebar tying tool (power tier), which feeds and twists the wire to form each tie.

A powered tier feeds and twists the wire without repeated manual wrist rotation and plier squeezing. This reduces repetitive hand work, but tool weight, grip, trigger use and posture still need assessment. Select the tool for the bar combination and maintain it so the ties remain secure.

Exam trap: Ergonomic tying pliers with cushioned handles: they ease grip pressure, but every tie is still a grip-and-twist cycle by hand, so the repetitive wrist motion remains.

Standard reference: RSOS 2025 C-11.02.02L (b)

In a lap splice of two bars embedded in concrete, how does the tension force pass from one bar to the other?

Answer: Through the surrounding concrete, by bond between each bar's deformations and the concrete along the lap length.

Each bar develops its force into the concrete along the lap, and the concrete passes it to the other bar. That is why lap length depends on bar size, bar grade, concrete strength, cover and spacing, and why the full lap and cover must be achieved.

Exam trap: Through the tie wire binding the bars together: ties only hold the bars in position and carry no meaningful force.

Standard reference: RSOS 2025 C-11.03.01L (a)

A lap table gives a longer 'top bar' lap for horizontal bars with more than 300 mm of fresh concrete cast below them in the same pour. Why do these bars need a longer lap than other bars of the same size?

Answer: Bleed water collects under them and the settling concrete pulls away from their undersides, so their bond is weaker and more length is needed.

A lap passes force between bars through bond with the concrete. A deep layer of fresh concrete below a horizontal bar settles and bleeds: water gathers under the bar and the paste separates from its underside, weakening bond there. The depth of concrete cast below the bar decides it, so top bars in a thin slab may not qualify.

Exam trap: Because top bars carry more load over supports: the longer lap comes from the bar's casting position and weaker bond, not from the load it carries.

Standard reference: RSOS 2025 C-11.03.01L (b)

Before the pour, a monostrand tendon’s sheathing has a short slit; the grease is intact and there is no moisture inside. What must the repair restore before the tendon is enclosed in concrete?

Answer: A continuous, watertight barrier that keeps the strand isolated from concrete, using the tendon system’s approved repair materials and procedure.

An unbonded tendon needs both corrosion protection and freedom to move relative to the concrete during stressing. Seal the damaged sheath to intact material using the approved repair method, without contaminating the strand or bonding it to the concrete. Tape type, overlap and any replacement sheath follow that system’s repair instructions.

Exam trap: Filling the slit with concrete patch material: that does not restore the sheath and can bond the strand locally, interfering with stressing.

Standard reference: RSOS 2025 D-12.02.04P

A pour's tendons have all been stressed and their elongations recorded. When may the strand tails be cut off?

Answer: After the engineer accepts the stressing records and authorizes cutting; then complete the specified cutting and protection sequence.

Rejected elongations may require corrective stressing, and the jack needs sufficient strand tail to grip. Cutting before acceptance can remove that option. Once cutting is authorized, the supplier’s finishing sequence provides the specified tail projection, cap seal and pocket protection.

Exam trap: Right after lock-off, to clear the deck. Once a tail is cut, a tendon with a rejected elongation can no longer be gripped by the jack.

Standard reference: RSOS 2025 D-13.03.02P

10 pairs · 1 decoyChecked at the end