Ironworker (Generalist) Flashcard Match
Online Red Seal Exam Preparation, built on official standardsSet up a round
Cards from
Pairs per round
Blocks
Decoys
240 cards to draw from
Your rounds
Kept on this device- 80%10 pairs · 4:12TodayRetry the wrong ones
- 70%10 pairs · 4:40TodayRetry the wrong ones
- 87%15 pairs · 6:05YesterdayRetry the wrong ones
- 100%10 pairs · 3:3111 NovPlay again
- 60%5 pairs · 2:2010 NovRetry the wrong ones
Checking
What a checked pair looks likeChecking
Clock
How a round works
Each card is the front of a flashcard from the set you chose.
Drag it onto its answer, or tap the card and then the answer. Every miss shows the right pair and the why behind it.
Browse the 20 free cards and explanations
A prescription antihistamine taken before shift carries a drowsiness warning. The day's work is operating a boom lift and connecting steel at 12 m. What must be done before starting?
Answer: Report the possible impairment before starting and have fitness for the lift and connecting work assessed; do not perform either task while impaired.
Medication can affect alertness, judgement and balance even when properly prescribed. These effects matter at boom-lift controls and while connecting at height. The drowsiness warning calls for checking medication advice and reporting possible effects so safe work can be arranged, rather than assuming that a prescription makes the tasks safe.
Exam trap: Work as usual because the drug is legal and prescribed: what matters is impairment, not legality, and drowsiness while operating a MEWP or connecting is a serious hazard.
Standard reference: RSOS 2025 A-1.03.03P
A base layout has a 6 m leg on the gridline and an 8 m leg on the proposed perpendicular. Their end-to-end diagonal is 10.06 m. How should the corner be squared without changing either leg length?
Answer: Swing the free end of the 8 m leg toward the gridline leg until the diagonal is 10.00 m, then secure and recheck the marks.
A 6–8–10 triangle gives a right angle. The longer diagonal shows the included angle is too open; shortening either set-out leg would change the base dimensions instead of correcting the angle. Keep the grid reference fixed and move only the perpendicular alignment.
Exam trap: Shorten the 8 m leg by 60 mm: that changes the required base dimension and does not establish a square corner.
Standard reference: RSOS 2025 A-3.02.03P
A lift plan requires a test lift before a heavy machine is set. What is a test lift, and what is checked before hoisting further?
Answer: Raising the load just clear of its supports and holding it there, to check brakes, crane stability and ground, rigging and load balance before going on.
A test lift finds problems while the load is only inches up and can be set straight back down: a brake that lets the load drift, outriggers or mats settling, slings or hardware not seated, or a load hanging out of level because the hook is not over the centre of gravity. Anything found is corrected and the test repeated before the full lift.
Exam trap: Hoisting slowly to full height while watching for trouble: by then a slipping brake or shifting load is high in the air instead of just above its supports.
Standard reference: RSOS 2025 B-6.02.12P
During a pre-use inspection, a wire rope sling shows a small arc strike where a welding electrode touched it. No wires are broken. What is done with the sling?
Answer: Tag it, remove it from service and report it: heat or arc damage is a removal criterion for wire rope.
An arc strike can alter the wire’s heat treatment and leave a brittle, weakened area before wires visibly break. RSOS B-7.01 identifies arc marks as rigging damage to be tagged, removed and reported. A broken-wire count cannot establish the safety of a heat-damaged sling.
Exam trap: Keep using it because no wires are broken: arc damage weakens the wires without breaking them, so broken-wire counts do not cover it.
Standard reference: RSOS 2025 B-7.01.03P
A trial lift leaves a beam’s west end low. The lift plan confirms that the hook would be east of the centre of gravity if the beam were held level. What is the safe sequence for correcting the bridle?
Answer: Land and support the beam, adjust the rated rigging to bring the hook over its centre of gravity, then repeat the test lift.
The known imbalance is corrected with the load safely supported. Adjust pick locations or leg lengths within the engineered arrangement, recheck individual leg loads and connections, and lift just clear to verify balance. A tag line controls rotation; it does not carry the force needed to level an unbalanced beam.
Exam trap: Shorten the west leg while the beam remains suspended: adjusting loaded rigging can release or shift the load unpredictably.
Standard reference: RSOS 2025 B-7.04.05P; B-7.04.01L (j)
Rigging hardware and a chain hoist must come down from a steel beam 10 m up after a lift. How are they brought to the ground?
Answer: Lowered on a hand line, or in a bag or bucket, into a cleared and barricaded area, never dropped or thrown.
Dropped hardware is a struck-by hazard to anyone below and is itself damaged: hooks bend, hoist housings crack and the gear can no longer be trusted. Lowering it on a hand line into a cleared area keeps it under control, and small items go down in a tool bag or bucket.
Exam trap: Drop them onto dunnage once the area below is clear: hardware can bounce or ricochet, and the impact can crack or bend it without obvious signs.
Standard reference: RSOS 2025 B-8.02.03P
Through roughly how much of a full circle can a stiffleg derrick's boom swing, and what sets that limit?
Answer: About 270°: the boom cannot swing into the sector between the two rigid stifflegs.
A stiffleg derrick's mast is braced by two rigid legs, usually about 90° apart, that resist both tension and compression in place of guy lines. The boom can work everywhere except the quadrant between the legs. The derrick is placed so every pick and set point lies inside that arc, with the mast base and stifflegs anchored for the forces at rated load.
Exam trap: A full 360°, because the mast rotates: the rigid stifflegs physically block the boom from the sector between them.
Standard reference: RSOS 2025 B-9.02.01L (c)
A 15M U-bar is to be field bent with two 90° bends to out-to-out dimensions of 300 mm, 900 mm and 300 mm. The bender chart lists a 40 mm deduction per 90° bend for 15M on this pin. To what length should the bar be cut?
Answer: 1 420 mm.
Out-to-out dimensions measure to the outside of each bend, so they overstate the bar actually used there. The cut length is the sum of the out-to-out dimensions minus one deduction per bend: 300 + 900 + 300 = 1 500 mm; 1 500 − 2 × 40 = 1 420 mm.
Exam trap: 1 500 mm, the sum of the out-to-out dimensions: bending uses less bar than the outside dimensions show, so the legs would come out about 40 mm too long each.
Standard reference: RSOS 2025 C-10.01.03P
A delivery of black 15M bar has light, even surface rust and no loose flakes. Under RSIC practice, when is rusted bar still acceptable to place?
Answer: When a hand-wire-brushed sample still meets the CSA minimum dimensions, mass and deformation height.
Light, tight rust and mill scale do not harm bond. RSIC accepts rusted bar if, after hand wire-brushing, its dimensions, mass per metre and deformation height still meet the CSA requirements. At the time of placing, bars must still be free of mud, oil and other substances that reduce bond.
Exam trap: Reject or sandblast all rusted bar: only loose, scabby rust or rust that has reduced the section below CSA minimums matters; light, tight rust is acceptable.
Standard reference: RSOS 2025 C-11.01.07P
A slab specification requires black annealed tie wire of 16 gauge or heavier. Coils marked 14 gauge and 18 gauge are available in the same gauge system. Which coil meets the minimum, and why?
Answer: The 14-gauge coil: a lower gauge number denotes a thicker wire in that system; 18 gauge is thinner than the specified minimum.
Gauge numbering runs opposite to diameter. “Or heavier” therefore permits a lower number, provided the wire material and condition also meet the specification. The same gauge system must be used when comparing marked sizes.
Exam trap: Choose 18 gauge because 18 is greater than 16: the larger number identifies thinner wire, not heavier wire.
Standard reference: RSOS 2025 C-11.02.02P; C-11.02.02L (d)
Which splicing method does CSA A23.3 rule out for 45M and 55M bars, and how are those sizes spliced instead?
Answer: Lap splicing is not permitted; they are joined with mechanical couplers or welded splices.
CSA A23.3 does not allow lap splices for bars larger than 35M, apart from specific compression and footing-dowel cases. Lap behaviour of such large bars is not reliably established, so 45M and 55M bars are spliced with full mechanical connections or welded splices that develop the bar. RSIC lap tables show 'lap not permitted' for these sizes.
Exam trap: A longer lap with extra ties: no lap length makes a lap acceptable for bars over 35M, outside the code's specific compression and footing-dowel exceptions.
Standard reference: RSOS 2025 C-11.03.01L (a)
What equipment contains the stored spring energy of a reelless prestressing-strand pack before its shipping bands are cut?
Answer: A suitable strand dispenser cage, with the pack secured in it before band removal.
The tightly wound pack can expand suddenly when the bands release. The cage contains the expanding coil and allows controlled centre payout. A loose pack on the ground can spring outward, tangle and kink, endangering workers and damaging the strand.
Exam trap: A flat patch of ground with the pack laid on its side: it provides no restraint against the coil springing open.
Standard reference: RSOS 2025 D-12.02.01P; D-12.02.03L (b)
During tendon stressing, why is measured elongation checked as well as jack force?
Answer: Elongation independently checks the tendon’s response to stressing and can reveal friction, slip or other problems that a force reading alone misses.
Jack force describes the force applied at the stressing end. Measured extension reflects how the tendon responds along its length. Both records are compared with the specified values and tolerances; a discrepancy is investigated and reported before cutting the tail or closing the pocket.
Exam trap: Elongation is only needed when the pressure gauge fails: the two checks provide different information even with a functioning gauge.
Standard reference: RSOS 2025 D-13.02.05P; D-13.02.03L (e)
A uniform 16 000 kg precast beam bears on a column corbel at one end and, centred, on a four-leg shoring tower at the other. The shoring table allows 2 500 kg per leg for jack extension up to 300 mm and 1 800 kg for over 300 up to 600 mm. The jacks are at 450 mm. Is the tower adequate?
Answer: No. Each leg carries 2 000 kg, but at 450 mm extension the 600 mm row governs, which allows only 1 800 kg per leg.
Tower reaction = 16 000 ÷ 2 = 8 000 kg (half of a uniform beam). Load per leg = 8 000 ÷ 4 = 2 000 kg. Capacity drops as screw jacks extend; 450 mm is beyond 300 mm, so the 600 mm row applies: 1 800 kg < 2 000 kg. Reduce the extension, add capacity or have the engineer revise the design.
Exam trap: Yes, because 2 000 kg is under 2 500 kg. That rating applies only up to 300 mm of jack extension, and these jacks are out 450 mm.
Standard reference: RSOS 2025 E-15.01.01L (e)
Wall girts are at the correct elevation at both rigid frames but sag between them before siding is fitted. How should the specified sag-rod system be used to line them up?
Answer: Adjust the sag-rod nuts to support and align the intermediate girt lines, then recheck straightness and level before cladding.
The end clips set the girt ends; the sag rods provide intermediate support and weak-axis restraint. Adjusting the clips alone changes the ends without removing mid-span droop. Work through the system so correcting one girt does not leave adjacent lines out of position.
Exam trap: Raise the end clips until the centre looks level: the ends would then be wrong and the intermediate support would remain unadjusted.
Standard reference: RSOS 2025 E-15.03.01L (b)
In a DTI trial assembly over an oversized hole, the load cell shows low bolt tension although several gaps reject the feeler gauge. The DTI body has cupped into the hole. What best explains the disagreement, and what must be corrected?
Answer: Unsupported DTI dishing has distorted the gap indication; correct the bearing support and repeat verification with sound components.
The indicator must bear as its manufacturer specifies so gap closure reflects protrusion compression. A body cupped into the hole changes that geometry and can mimic gap closure at inadequate tension. Correct the specified washer or plate support for this hole and DTI; a closed gap alone cannot validate the distorted assembly.
Exam trap: Accept the tight gaps and disregard the low load-cell reading: a distorted indicator is not evidence of the required bolt tension.
Standard reference: RSOS 2025 E-15.04.05P
Two railing-post bases have equal fillet-weld size and length, but B’s weld lines are closer together. Lateral pull tests applied at base level give similar results. Do those tests establish equal performance with the same force applied at handrail height?
Answer: No. The test omits the service overturning moment, and B’s narrower weld spacing changes its resistance; obtain engineered acceptance at the actual load.
Moving the force up the post adds moment at the base. Resisting that moment depends on weld-group geometry as well as weld area; closer weld lines change the force couple. A similar base-level shear response therefore cannot establish equivalent service performance. Keep the specified detail until the proposed change is accepted.
Exam trap: Accept B because total weld area and test force match: neither comparison accounts for the elevated load and changed weld spacing.
Standard reference: RSOS 2025 E-16.02.01L (b)
On an overhead power-and-free conveyor, how can one carrier stop at a workstation while the rest of the line keeps moving?
Answer: Its trolley disengages from the pusher dogs of the continuously running power chain and stands on the unpowered free track.
A power-and-free system has two tracks: a power track with a moving chain carrying pusher dogs, and a free track carrying the load trolleys. A stop, or the carrier ahead, releases a trolley from the dogs, so carriers can accumulate, queue or switch while the chain keeps running.
Exam trap: The whole chain stops at each station. That describes a simple overhead chain conveyor; power-and-free lets each carrier stop on its own.
Standard reference: RSOS 2025 E-17.01.01L (d)
A raised hydraulic platform has no accumulator. After pump lockout, the main gauge reads zero, but a cylinder-side gauge recovers after a controlled bleed. What energy source and isolation boundary must the decommissioning plan address?
Answer: The raised load can re-pressurize the cylinder; establish positive mechanical support and verify isolation and pressure relief on the load side.
The zero main reading does not describe a cylinder isolated by a load-holding valve. With the pump isolated and no accumulator, the raised load remains a source of pressure and motion. Support or safely lower it using the approved method, then isolate and verify the load-side circuit before opening it; repeated bleeding alone is not control.
Exam trap: Repeat the pump start test until the main gauge stays at zero: it already reads zero and does not verify the energy in the load-side circuit.
Standard reference: RSOS 2025 F-18.01.01L (a)
An edge-bent flat bar has no twist. After one controlled vee heat with its broad base on the concave edge, the cool bar’s bend is tighter. The temperature limit was respected. What should be corrected before further approved straightening?
Answer: Review the heat pattern: the broad base belongs on the convex, stretched edge for this bend; increasing temperature would worsen the wrong-edge shrinkage.
Vee heating produces greatest permanent shortening near its wide base. Shortening the already shorter concave edge tightens the curvature, matching the observed result despite correct temperature control. The heat location and pattern, not simply heat intensity, must suit the deformation and approved repair procedure.
Exam trap: Use a hotter heat in the same place: more shrinkage on the concave edge can increase the bend and exceed the material’s temperature limit.
Standard reference: RSOS 2025 F-19.02.05P; F-19.02.01L (d)