Pass Your Red Seal

Auto Body and Collision Technician Flashcard Match

Online Red Seal Exam Preparation, built on official standards
Flashcard Match10 pairs · 1 decoyChecked at the endStart matching

Set up a round

Cards from

Pairs per round

Blocks

Decoys

240 cards to draw from

ACommon occupational skills30
BRepairs frame and structural components56
CRepairs non-structural outer body panels and related components48
DRepairs mechanical, electrical and alternative-fuel system components26
ERepairs interior components and services restraint systems24
FRefinishing procedures44
GDetailing and cleaning12

Your rounds

Kept on this device
Average79%
Best100%

Checking

What a checked pair looks like
Browse the 20 free cards and explanations

During a rail pull on a frame rack, the air-over-hydraulic tower ram stops short of full stroke under load; the pump runs normally and shop air at the pump is at the manufacturer's specified pressure. Which check comes first before the pull continues?

Answer: Check the hydraulic fluid level in the pump reservoir per the manufacturer's specification and top up with the specified fluid; low fluid stops full extension.

The ram can only extend as far as the fluid the pump can deliver. A low reservoir lets the pump draw air, so the ram stalls or falls short before the pull is complete, and air in the system makes a loaded pull unpredictable. Fluid level is checked per the manufacturer with the ram in the specified position, and any leak that caused the loss is found and repaired.

Exam trap: Turning up the air regulator to force more pressure: the air is already at specification, and exceeding it damages the pump without adding fluid volume.

Standard reference: RSOS 2019 A-2.02.02P

A pickup had both front wheels removed during a fender and suspension repair and is now ready for its road test. Which checks on the wheels must be completed first, and how?

Answer: Torque each wheel fastener to OEM specification with a calibrated torque wrench in the specified pattern, and set tire pressures to the placard values.

The final operational check requires tire pressure and wheel torque to be verified before the road test according to OEM specifications. An impact gun does not control torque: under-torqued wheels can loosen and over-torqued studs stretch or warp hubs and rotors. Pressures set to the door placard restore handling, advanced driver assistance system (ADAS) and TPMS behaviour for the test.

Exam trap: Snugging the nuts with an impact wrench and checking pressure after the road test: the drive itself becomes the hazard the check is meant to prevent.

Standard reference: RSOS 2019 A-7.01.04P

A 2020 full-frame pickup was hit in the right rear. The box sits 15 mm closer to the cab on the right than on the left, the right bumper is pushed in, and a wrinkle shows in the right frame rail ahead of the rear spring hanger. Which method establishes whether the frame needs straightening?

Answer: Measure the frame directly against OEM frame dimensions (datum height, centreline, cross and length checks at the reference holes), not from the body gaps.

On a full-frame vehicle the cab and box ride on rubber mounts, so cab-to-box misalignment is a symptom that something beneath moved, not a measurement of it. The wrinkle ahead of the hanger says energy reached the rail. Cross measuring and comparison measuring of the frame at its reference points against OEM data isolate the hidden damage and show how far forward it travelled.

Exam trap: Re-centring the box on its mounts to even up the gap; the mismatch and the wrinkle are evidence of frame damage that must be measured before any body adjustment.

Standard reference: RSOS 2019 B-9.01.02P

A 2019 sedan is being set up on a bench. Its pinch welds carry about 2 mm of rubberized undercoating and are hidden by plastic sill covers. The first clamp slipped during a trial pull. What preparation of the anchoring locations is required before clamping again?

Answer: Remove the sill covers and strip undercoating and sealer from each clamp footprint to clean metal, then check that the clamp jaws are sharp and clean.

Preparing anchoring locations includes removing components, undercoating and paint. Serrated clamp jaws must bite steel; a rubberized coating lets the body creep under load, giving false movement, damaging the flange and risking a sudden release. Clean metal at the pinch weld, inspect jaw teeth for wear and tighten clamps evenly, then re-check that the baseline measurements have not moved.

Exam trap: Simply tightening the clamps harder over the coating; the coating still shears and the extra force crushes the pinch weld instead of gripping it.

Standard reference: RSOS 2019 B-9.03.02P

Hot-stamped boron steel used for B-pillar reinforcements reaches about 1 500 MPa tensile strength, far above what its alloy content alone would give. What forming process creates that strength, and why does repair heat remove it permanently?

Answer: Press hardening: the blank is formed hot and quenched in the die, locking in martensite; repair heat tempers that martensite and the shop cannot re-harden it.

Mild and HSLA steels get their strength from alloying and work, so they tolerate repair heat where the OEM allows. Boron UHSS gets its strength from microstructure: the blank is austenitized at about 900 °C, formed and quenched in the die to martensite. Torch or weld heat softens that zone, and the metal's low ductility means cold pulling cracks it, so OEMs list these parts as replace only.

Exam trap: Believing a brief, low heat 'stress relieves' it like mild steel; any tempering heat lowers strength and there is no field method to re-harden it.

Standard reference: RSOS 2019 B-10.01.01L

A replacement outer rocker reinforcement is to be GMAW (MIG) plug welded to the retained inner flange, reproducing the factory spot-weld count. In which panel are the plug-weld holes made, and what must each weld do through its hole?

Answer: In the new panel, before it is fitted; the arc fills the hole and fuses through it into the solid retained flange so both layers are joined at that point.

Preparation includes drilling or punching plug-weld holes to the OEM diameter, count and spacing. The hole exposes the lower sheet: the weld is sound when the puddle fuses the hole wall and penetrates the retained flange, leaving a slight crown. Where spot-weld removal left holes in that flange, follow the OEM procedure (close them or offset the plug welds) so every weld sits on solid metal.

Exam trap: Drilling through both panels so the weld fills one deep hole; with no lower sheet to fuse into, the puddle blows through or only bridges the hole edges and the joint carries little load.

Standard reference: RSOS 2019 B-10.03.01L

A windshield's frit band on a 2022 crossover is being prepared. The urethane system calls for an activator wipe, then glass primer with a 10 minute flash before the bead. Running late, the plan is to prime and bead at once. What is wrong with that plan, and what is the consequence?

Answer: Beading over unflashed primer: trapped solvent weakens the urethane-to-glass bond and the glass can release in a crash; wait the full 10 minute flash first.

Mating areas are prepared with primers to OEM and adhesive-maker procedures for adhesion and corrosion protection. Glass primer bonds to the frit only after its solvent has flashed; urethane laid on wet primer traps solvent, the bond never reaches its rated strength and the windshield can let go when an airbag loads it. Use one manufacturer's matched activator, primer and urethane.

Exam trap: Treating the primer like a wipe-on cleaner because the glass looks clean: the flash time is a chemical requirement of the adhesive system, not a drying convenience.

Standard reference: RSOS 2019 B-11.02.03P

A quarter panel dent beside the fixed quarter glass and the rear door is to be ground to bare metal with an angle grinder. The glass and the door are undamaged and will stay on the vehicle. What protection is needed before grinding starts?

Answer: Cover the glass and the adjacent door with welding blankets or heat-resistant covers and mask the panel edges; hot grinding sparks embed in glass and paint.

Surrounding areas and unrelated components must be protected from further damage such as sparks and grinding marks. Grinding throws red-hot steel particles that fuse into glass as permanent pits and into paint as rust specks that cannot be polished out, so the glass and door are shielded beforehand rather than cleaned afterward.

Exam trap: Masking only the paint edge next to the repair with tape: tape stops sanding scratches, but hot sparks burn through it and travel well beyond it to the glass.

Standard reference: RSOS 2019 C-12.01.04P

After the first block sanding of cured filler on a steel quarter panel, dozens of small pinholes show across the filler surface. The filler is fully hard and the contour is correct. What is the correct corrective action?

Answer: Press a thin skim of filler or finishing glaze into the pinholes with a spreader, let it cure and block sand again before priming.

Imperfections are identified visually and by touch and corrected according to their type. Pinholes are trapped air from a whipped mix or a thick first coat; they are open voids, so the fix is re-application of filler pressed firmly into the holes. Primer-surfacer bridges rather than fills them, and they reappear in the topcoat as pinholes or solvent pops.

Exam trap: Spraying extra high-build primer to fill them: primer shrinks into open pinholes and the defects telegraph through the finish.

Standard reference: RSOS 2019 C-12.03.10P

A fender liner on a 2020 SUV is held by plastic push retainers whose centre pin has a Phillips-head recess. How is this type of retainer released without breaking it?

Answer: Turn the centre screw counter-clockwise a few turns so the expanding legs relax, then pull the retainer straight out; it is reset by turning the screw back in.

Fasteners are identified to determine the method of removal. A screw-type retainer expands its legs when the centre screw is driven in, so prying the whole retainer out while it is still expanded shears the legs or tears the liner hole. Backing the screw off collapses the legs and frees it undamaged for reuse.

Exam trap: Prying it out whole with a trim tool as if it were a plain push-pin: the expanded legs break off and the liner hole is torn.

Standard reference: RSOS 2019 C-13.02.01L

A door glass on a 2019 sedan is bolted to the regulator lift bracket, and the only access to those bolts is through two holes in the inner door panel. The trim panel is off, the switch is unplugged and the glass sits fully down with the bolts hidden. What is the correct way to reach the bolts?

Answer: Reconnect the switch temporarily and run the glass until the lift-bracket bolts line up with the access holes, then support the glass and loosen them.

Glass is positioned to access fasteners. The lift bracket travels with the glass, so the regulator is used to bring the bolts to the service holes the OEM provides; the glass is held by hand or taped across the frame before the bolts come out so it cannot drop into the door. Forcing the glass by hand loads the regulator cables and gears and can strip or jam them.

Exam trap: Pulling the glass up by hand to find the bolts: the regulator resists, the cable can jump its drum, and the glass may drop once the bolts release.

Standard reference: RSOS 2019 C-14.01.02P

A rear-impact pickup's plastic fuel tank has been drained and removed. Both steel straps are kinked, the tank has a white stress crease along one lower corner with no wetness or odour at the crease, and the vapour-line quick-connect retainer is cracked. Which of these parts may be reinstalled?

Answer: None: a creased plastic tank has yielded and is replaced, never repaired; the kinked straps and the cracked retainer are safety parts and are replaced as well.

Mechanical components are inspected for collision damage before reuse. Stress whitening in a polyethylene tank marks material that has yielded and may weep or split later, and OEM and industry practice is to replace, never repair, a fuel tank. Kinked straps have lost their shape and preload. A cracked retainer cannot seal or hold the line, and a vapour leak is an emissions and a fire issue.

Exam trap: Reusing the tank because it is dry and does not leak now; a dry crease in a plastic tank is still yielded material carrying fuel, and the straps meant to hold it are already compromised.

Standard reference: RSOS 2019 D-16.01.02L

A frontal impact cracked the case of a sedan's flooded lead-acid 12 V battery; electrolyte has pooled in the battery tray and the battery is coming out for replacement. How are the battery and the spill dealt with?

Answer: Use the spill procedure to neutralize and collect the acid; contain the leaking battery in acid-resistant secondary containment for a lead-acid recycler.

Sulphuric acid can burn skin and eyes, and the battery contains lead. Trained personnel use the SDS spill procedure with acid-resistant gloves, protective clothing and splash goggles. Baking soda solution can neutralize spilled acid; collect the residue. Keep the damaged battery upright and contained while arranging recycling.

Exam trap: Draining the remaining electrolyte to make the battery lighter: this creates another acid release and can contaminate drains or soil.

Standard reference: RSOS 2019 D-17.01.04P

A cracked door trim panel is moulded with the symbol >PP-TD20<. What does the marking tell the repairer about the material and the repair approach?

Answer: Polypropylene with 20% talc filler: a thermoplastic. Match the welding rod or select a compatible adhesive system and its specified surface preparation.

The moulded mark identifies polypropylene with 20% talc filler. Use that identification to select compatible repair materials. Polyolefins have low surface energy, so adhesive selection and preparation matter; use the adhesion promoter specified by the chosen repair system rather than assuming any adhesive will bond.

Exam trap: Reading TD20 as a glass-fibre content or a different plastic family and choosing a rod by colour or flexibility: the polymer code, not appearance, decides the rod.

Standard reference: RSOS 2019 E-18.01.01L

After a moderate frontal collision a sedan's driver belt webbing retracts and locks, the pretensioner did not fire and no DTC is stored. Which visible webbing condition would still indicate the assembly must be replaced?

Answer: Glazed, fused or flattened fibres (or any cut, fraying or stretched, stiff section) near the D-ring or latch plate, showing the webbing was loaded in the crash.

Failed seat belt indicators include visible damage, DTCs and a deployed retractor. Crash loading drags the webbing through the D-ring and latch plate under heat and tension, glazing or fusing the fibres and stretching them, which lowers strength even though the belt still works by hand. OEMs require replacement of damaged webbing, and most also replace belts in use during the collision.

Exam trap: Passing the belt because it retracts, locks and shows no code: the indicators are additive, and visible damage on its own condemns the assembly.

Standard reference: RSOS 2019 E-19.01.04P

A two-tone pickup needs its lower silver section repainted up to a straight colour-break line on the door, with the upper white left untouched. The break must be razor sharp and follow a slight body curve. Which masking product forms the line itself, and how is the paper then attached?

Answer: Lay fine-line vinyl tape on the break line first, then apply crepe tape and paper on top of it, overlapping the vinyl without touching the paint line.

Fine edge (vinyl) tape is applied according to job requirements where a crisp, straight or gently curved paint line is needed: its thin, flexible, non-wicking edge seals against the panel and follows curves without wrinkling. Crepe paper tape is porous and crinkles on curves, so it bleeds and leaves ragged edges when used as the colour line; it belongs on top of the vinyl to hold the paper.

Exam trap: Using 18 mm crepe tape as the colour-break line because it is faster: paint wicks under its edge and the tape cannot follow the curve cleanly.

Standard reference: RSOS 2019 F-20.02.07P

In a crossdraft booth, airflow enters through the door filters at one end and exits through the exhaust wall at the other. A sedan's front fender and a loose bumper cover on a stand both need basecoat in one session. Where should the stand be placed to keep overspray off the cover?

Answer: Upstream of the fender, between the intake filters and the car, so air carries fender overspray away from the cover toward the exhaust; paint the cover first.

Booth space is used according to the work: in a crossdraft, overspray travels with the air from intake to exhaust, so anything downstream of the panel being sprayed collects dry overspray. Placing the stand nearer the intake keeps it in clean air, and spraying it first means the fender's overspray never crosses a wet part.

Exam trap: Placing the stand behind the car near the exhaust 'where the fumes go': that is exactly where the fender's overspray settles.

Standard reference: RSOS 2019 F-22.01.04P

A spray-out card of a solid red beside the polished fender under colour-corrected light shows the same lightness and the same redness, yet the card looks dirtier and greyer than the vehicle. Which dimension of colour is off?

Answer: Chroma, the colour's saturation or cleanliness: the card is lower in chroma (greyer, dirtier) while value and hue already match.

Colour theory describes a colour by three elements: value (light or dark), hue (the colour family or cast, red to orange or blue) and chroma (how clean or saturated versus grey). Comparisons are done one dimension at a time. Here value and hue agree, so the remaining difference, a muddy or dull look, is chroma, corrected by adding a cleaner toner of the same hue or less of the greying toner.

Exam trap: Calling it a value problem and adding white or black: that changes lightness, which already matches, and leaves the dirty cast.

Standard reference: RSOS 2019 F-23.02.01L

A basecoat/clearcoat door is cleared with a 2K urethane clear whose technical data sheet (TDS) lists a minimum dry film of 50 µm (2 mils). If the clear is applied below that or buffed too thin, which protective property is lost first, and what is the long-term consequence?

Answer: UV protection: the clear carries the UV absorbers, so a thin film lets sunlight reach and break down the basecoat, causing fade, chalking and delamination.

The role of clear coat is gloss, chemical and scratch resistance, and especially ultraviolet protection for the basecoat, which has little durability of its own. UV absorbers work in proportion to film thickness, so a clear under its minimum build, or sanded thin during defect correction, lets UV degrade the basecoat and the clear's bond to it. Film build is checked, not guessed.

Exam trap: Assuming gloss proves the clear is sound: a thin clear can look perfect at delivery and fail months later by peeling.

Standard reference: RSOS 2019 F-24.04.01L

The polycarbonate headlamp lenses on a repaired crossover are yellowed and hazed, and the customer wants the undamaged side to match the new lamp on the repaired side without replacing it. Which procedure restores clarity so it lasts?

Answer: Mask the paint, wet sand through finer grits to remove the degraded coating, polish with plastic polish, then apply a UV-resistant clear coating or sealant.

Yellowing is the oxidized factory UV hardcoat. Sanding (for example P800 to P3000) removes the failed layer and polishing restores optical clarity, but it also removes the lens's UV protection, so bare polycarbonate re-yellows within months. A dedicated UV-resistant clear restores that protection. Surrounding paint is masked because sanding slurry and the polisher can damage it.

Exam trap: Stopping after polishing because the lens looks clear: without new UV protection the lens hazes again quickly and the customer returns.

Standard reference: RSOS 2019 G-26.02.06P

10 pairs · 1 decoyChecked at the end