Pass Your Red Seal

Welder Flashcards

Online Red Seal Exam Preparation, built on official standards
FlashcardsSet 1 · Card 58 of 12554% to goTry 20 flashcards

Cards by block

In each set of 125
  • ACommon Occupational Skills20 cards
  • BLayout and Fabrication of Components for Welding28 cards
  • CCutting and Gouging23 cards
  • DWelding Processes54 cards
  • 78%Set 2 · 125 cards · 98 known
  • 72%Set 2 · 125 cards · 90 known

What is on a card

A-1.01Block A · Recall

Why must both cutting lips of a resharpened twist drill have equal length and angle?

Answer
To keep the point centred so both lips share the cut and the hole is not oversized.
Why
Unequal lips put the drill point off the spindle axis. One lip carries more load and sweeps a larger radius, so the drill can cut oversize and wander.
Exam trap
Equal lip clearance alone is insufficient; it does not correct unequal cutting-lip lengths.

From the Welder standard: RSOS 2023 A-1.01.05P

Browse the 20 free cards and explanations

Why must both cutting lips of a resharpened twist drill have equal length and angle?

Answer: To keep the point centred so both lips share the cut and the hole is not oversized.

Unequal lips put the drill point off the spindle axis. One lip carries more load and sweeps a larger radius, so the drill can cut oversize and wander.

Exam trap: Equal lip clearance alone is insufficient; it does not correct unequal cutting-lip lengths.

Standard reference: RSOS 2023 A-1.01.05P

A fume extractor at a welding bench sounds normal, but the hood capture has weakened since nearby duct alterations. Visible fume passes the breathing zone. What is the justified action before continuing?

Answer: Stop and have source-capture airflow checked and restored; fan noise does not prove capture.

Effective extraction depends on capture airflow at the source, not merely fan rotation. Duct changes can alter system resistance or balance and allow fume into the breathing zone.

Exam trap: Moving the hood closer may help capture, but it does not establish that the altered system has adequate airflow.

Standard reference: RSOS 2023 A-3.02.02L

A cut 350WT remnant has lost its heat mark. Its grade and dimensions match two stock heats, but only one heat has the ordered impact-test category. Can the required heat be assigned from the grade and dimensions?

Answer: No; restore a documented heat-identity link before accepting or remarking the remnant.

Grade and dimensions cannot distinguish the two heats or prove the required impact category. Traceability must connect the physical remnant to its actual certificate before its heat mark is restored.

Exam trap: Choosing the heat with acceptable impact results would create a certificate link unsupported by material identity.

Standard reference: RSOS 2023 A-5.02.02P

Why must the follower-to-torch offset be allowed for in a mechanical flame-cutting template?

Answer: The follower tracks the template edge while the torch cuts on an offset path.

The guiding contact and cutting axis are not necessarily coincident. Their separation must be incorporated in the template geometry so the cut follows the intended finished profile.

Exam trap: Adding kerf allowance alone does not account for a separate guide-to-torch offset.

Standard reference: RSOS 2023 B-7.01.05P

Why must a structural angle layout identify the heel rather than treating the curved root fillet as a sharp inside corner?

Answer: The root radius is not the theoretical intersection used as the heel reference.

The heel is the theoretical intersection of the two outside back faces of an angle. The rounded inside fillet is a different physical feature and cannot substitute for that reference.

Exam trap: Measuring from a convenient point on the inside fillet shifts the layout datum unpredictably.

Standard reference: RSOS 2023 B-7.02.03P

What is the root face on a groove-weld edge preparation?

Answer: The unbevelled portion at the root end of the prepared edge.

The root face is the remaining square land at the root end of an edge. It helps define the root geometry along with the opening and prepared face.

Exam trap: The root opening is a gap between fitted members, not a portion of one prepared edge.

Standard reference: RSOS 2023 B-8.01.05P

A temporary strongback crosses a groove seam. Its attachment welds will be removed. What must its removal plan protect on the finished component?

Answer: The required parent-metal thickness and surface integrity at each attachment.

Temporary attachment removal can gouge or thin the component. The plan must include a permitted removal and surface restoration method that preserves the finished material requirements.

Exam trap: Breaking the strongback free without controlling attachment removal can tear out parent metal.

Standard reference: RSOS 2023 B-8.02.08P

A steel grinding wheel soon develops bright metallic patches when used on aluminium. Removal slows although abrasive grains remain visible; more pressure increases smearing. What consumable change addresses the cause?

Answer: Replace it with a compatible wheel specifically designed to resist loading on aluminium.

Soft aluminium can adhere to grains and fill the wheel surface, making it rub instead of cut. Bright metallic loading plus increased smearing under pressure identify that mechanism. An aluminium-rated abrasive addresses it; extra force adds heat and loading.

Exam trap: Grinding harder to expose fresh grain increases heat and smearing when aluminium is loading the wheel.

Standard reference: RSOS 2023 C-9.01.03P

Compared with a neutral oxy-acetylene flame, what visible change in the inner cone indicates an oxidizing mixture?

Answer: The inner cone becomes shorter and more pointed.

Adding oxygen beyond the neutral adjustment shortens and sharpens the oxy-acetylene inner cone and produces a more pronounced hiss. A fuel-rich feather indicates the opposite mixture direction.

Exam trap: A long acetylene feather indicates a carburizing flame, not an oxidizing one.

Standard reference: RSOS 2023 C-10.03.01L

Why must a liquid-cooled plasma torch use the specified torch coolant rather than an unapproved automotive antifreeze?

Answer: Unapproved antifreeze chemistry can damage or obstruct the torch cooling system.

Plasma coolant must suit the cooling passages, materials and required purity. Hypertherm prohibits substituting automotive antifreeze because its chemicals can damage the system. Matching freeze protection alone does not establish compatibility.

Exam trap: Choosing coolant solely by its freezing point ignores additives and the torch-system compatibility requirements.

Standard reference: RSOS 2023 C-11.02.02L

Which air carbon-arc electrode cross-section is suited to washing weld reinforcement flush over a broad surface?

Answer: A flat, rectangular carbon electrode.

The broad flat cross-section suits surface washing and removing reinforcement flush with the base material. A round electrode concentrates removal into a more rounded groove. Select the approved current range for the actual shape and size.

Exam trap: A round carbon is a normal grooving choice but does not provide the same broad flat washing profile.

Standard reference: RSOS 2023 C-12.01.04P

A dry E7018 batch runs smoothly on DCEP but repeatedly loses its arc on an AC transformer at the same approved current. Raising current overheats the rods. Which consumable compatibility should guide the next selection?

Answer: Check electrode compatibility with the AC source’s available open-circuit voltage.

Current is adequate on DC, while more AC current overheats the rods instead of stabilizing the arc. AC re-establishment can depend on electrode/source voltage compatibility; an approved low-OCV AC formulation may be required.

Exam trap: Selecting only by nominal strength and diameter overlooks AC arc-establishment characteristics.

Standard reference: RSOS 2023 D-13.01.02P

What does ripple describe in the output of a rectified DC SMAW source?

Answer: Alternating variation remaining on the rectified DC output.

Rectifying AC establishes one current direction but need not produce perfectly smooth DC. Ripple describes the residual cyclic variation, rather than reversal of the average output polarity.

Exam trap: Treating ripple as normal AC polarity reversal confuses varying DC magnitude with alternating current direction.

Standard reference: RSOS 2023 D-13.03.01L

A surface crack is found in a SMAW repair area. After its full extent is established, what preparation is required before rewelding under the approved repair procedure?

Answer: Excavate to sound metal and verify complete crack removal before rewelding.

Depositing metal over a crack does not remove its tip or restore the surrounding unsound region. The approved repair preparation must remove the complete discontinuity before sound fusion is rebuilt.

Exam trap: Capping the visible line can hide the crack while leaving its deeper ends intact.

Standard reference: RSOS 2023 D-13.04.10P

What does the letter 'S' identify in the ER70S-6 filler-metal classification?

Answer: A solid wire or rod.

In this designation, S identifies a solid filler form. It distinguishes the product from tubular cored wires; other parts of the classification identify strength and chemistry.

Exam trap: Reading S as self-shielded would omit the external shielding needed by this solid GMAW wire.

Standard reference: RSOS 2023 D-14.01.02L

In a MIG gun, what is contact-tip keyholing?

Answer: Elongation of the contact tip's wire bore through wear.

The wire rubs against the tip as current transfers through that contact. Bore wear can become elongated, weakening consistent electrical contact and wire guidance.

Exam trap: Increasing drive-roll pressure does not restore the worn tip's contact geometry.

Standard reference: RSOS 2023 D-14.02.01P

Wire delivery stalls as a GMAW gun heats. The spool and roll drive check free; the straightened gun feeds freely when its contact tip is removed. The cooled tip then feeds normally. Which area needs correction before changing voltage?

Answer: Investigate the contact tip’s heat-related feed restriction and verify its size and condition.

Removing the tip restores free feeding without changing the upstream path, and cooling changes the symptom. That localizes the restriction to the tip area; it does not justify replacing the power source or guessing a new arc setting.

Exam trap: Increasing drive-roll pressure pushes harder against the restriction and may buckle the wire.

Standard reference: RSOS 2023 D-14.03.04P

What is the purpose of a GTAW torch's collet?

Answer: It grips the tungsten and provides electrical contact within the torch.

The collet secures the electrode when the back cap is tightened. Its fit must suit the tungsten so the electrode stays located and receives current reliably.

Exam trap: Treating the ceramic cup as the tungsten clamp confuses gas coverage with the torch's gripping assembly.

Standard reference: RSOS 2023 D-15.01.02L

What is the purpose of GTAW pre-flow before starting the arc?

Answer: Establish shielding by displacing air from the torch gas path before the arc heats the metal.

Pre-flow establishes the protective atmosphere before the tungsten and pool become hot. It serves a different part of the cycle from protection during cooling after arc termination.

Exam trap: Adding post-flow alone cannot protect the first instant of an arc started in residual air.

Standard reference: RSOS 2023 D-15.03.03P

How does bonded SAW flux differ in manufacture from fused flux?

Answer: Bonded flux granulates ingredients with a binder; fused flux is melted, solidified and crushed.

The names describe different manufacturing routes. They are not, by themselves, proof of a particular deposited strength or a universal reconditioning temperature.

Exam trap: Treating bonded and basic as synonyms confuses manufacturing method with chemical character.

Standard reference: RSOS 2023 D-16.01.02L

20 free cardsCards 1 to 20 · no account needed