Mobile Crane Operator Flashcards
Online Red Seal Exam Preparation, built on official standardsCards from
Blocks
How many cards
Card order
Show
110 cards selectedof 110
Set 1
In progress35known15to review again60not marked
Set 2
Finished twice86known24to review again0not marked
Cards by block
In each set of 110- ACommon occupational skills7 cards
- BHoisting calculations20 cards
- CInspects and maintains crane14 cards
- DRigging13 cards
- EPlans lift, prepares site and sets up crane16 cards
- FAssembles, disassembles and transports crane15 cards
- GOperates crane25 cards
Recent sessions
All sessions in Progress- 78%Set 2 · 110 cards · 86 known
- 72%Set 2 · 110 cards · 79 known
What is on a card
A-1.03Block A · Critical thinking
A periodic inspection certificate expires next month, but its serial number identifies a different crane. Today's daily check passed. Can these records establish this crane's required periodic inspection status?
- Answer
- No. Obtain the valid periodic inspection record identifying this crane before relying on that status.
- Why
- Validity dates matter only after equipment identity matches. A successful daily check does not demonstrate that this crane received the separate required periodic inspection.
- Exam trap
- Accepting the unexpired certificate overlooks the serial-number mismatch; it documents another machine.
From the Mobile Crane Operator standard: RSOS 2021 A-1.03.07P
Cards from
Blocks
How many cards
Show
110 cards selectedof 110
Sources
- Mobile Crane Operator RSOS 2021Red Seal Program · FreeOpen
Blocks
- ACommon occupational skills
- BHoisting calculations
- CInspects and maintains crane
- DRigging
- EPlans lift, prepares site and sets up crane
- FAssembles, disassembles and transports crane
- GOperates crane
A-1.03Block A · task 1 · sub-task 3
Flashcards for every tradeBrowse the 20 free cards and explanations
A periodic inspection certificate expires next month, but its serial number identifies a different crane. Today's daily check passed. Can these records establish this crane's required periodic inspection status?
Answer: No. Obtain the valid periodic inspection record identifying this crane before relying on that status.
Validity dates matter only after equipment identity matches. A successful daily check does not demonstrate that this crane received the separate required periodic inspection.
Exam trap: Accepting the unexpired certificate overlooks the serial-number mismatch; it documents another machine.
Standard reference: RSOS 2021 A-1.03.07P
A load tag reads "8 tons" without a unit system. An equipment record says 7 260 kg, while the lift plan assumes 8 000 kg. What discrepancy must be resolved before accepting the documented mass?
Answer: Confirm whether "tons" means US short tons or metric tonnes with the load-information issuer.
Eight US short tons are about 7 257 kg, consistent with the equipment record; eight metric tonnes are 8 000 kg. The figures suggest a unit mismatch that must be confirmed at the source.
Exam trap: Averaging the two masses produces a number that neither document supports and does not resolve the unit.
Standard reference: RSOS 2021 B-3.01.02P
A load's underside must land at 18 m elevation. Its lifting points are 3 m above its underside; rigging rises 4 m to the hook, and required hook-to-tip clearance is 2 m. What minimum tip height must the range diagram provide?
Answer: 27 m above the same elevation datum.
All vertical spaces must fit: 18 + 3 + 4 + 2 = 27 m. A tip reaching the load's landing elevation alone leaves no space for the load, rigging and block clearance.
Exam trap: Using 25 m omits the specified 2 m hook-to-tip clearance.
Standard reference: RSOS 2021 B-4.01.02P
For a stated wind band, this crane's chart requires multiplying its 12 000 kg gross rating by 0.75 before deductions. The measured wind is within that band. What reduced gross rating applies?
Answer: 9 000 kg before the required deductions.
Apply the stated manufacturer factor to the gross rating: 12 000 × 0.75 = 9 000 kg. Then apply the chart's specified deductions to obtain net capacity.
Exam trap: Subtracting 0.75 t misreads a dimensionless factor as a fixed weight deduction.
Standard reference: RSOS 2021 B-4.02.05P
A wire-rope sling has a 40 kN vertical WLL. For this bend diameter, its manufacturer specifies a 0.85 D:d factor. With no other reductions, can it carry a 35 kN leg tension?
Answer: No; its reduced WLL is 34 kN.
The bend factor reduces capacity to 40 × 0.85 = 34 kN. The required 35 kN exceeds that permitted capacity even though it is below the straight-pull tag rating.
Exam trap: Using the unadjusted 40 kN rating ignores bending over the specified small diameter.
Standard reference: RSOS 2021 B-5.02.01P
The hydraulic reservoir level is to be checked with all specified cylinders retracted. Several are extended and the sight glass reads low. What must be done before deciding to add oil?
Answer: Place the cylinders in the manufacturer's specified checking positions, then read the level.
Oil held in extended cylinders changes reservoir level. The prescribed configuration makes the reading comparable to the maker's marks and avoids overfilling.
Exam trap: Adding oil immediately treats a configuration-dependent reading as a true shortage.
Standard reference: RSOS 2021 C-6.04.01P
Why must ground immediately around an outrigger mat be monitored along with the ground directly beneath it?
Answer: Soil movement beside the mat can reveal loss of support before obvious vertical settlement.
The supporting soil spreads the outrigger force beyond the mat footprint. Cracking or displacement nearby can indicate developing bearing failure.
Exam trap: Watching only the bubble level can miss an early ground change before the crane tilts.
Standard reference: RSOS 2021 C-7.05.01P
A sling's sewn identification tag is legible, but the load-bearing stitching at its eye is cut. What part of the sling must govern the inspection decision?
Answer: The damaged load-bearing eye stitching, assessed against the maker's rejection criteria.
The eye transfers load through its designed stitched connection. A readable tag identifies the sling but cannot establish the strength of damaged structural stitching.
Exam trap: An intact web body does not compensate for a damaged eye connection.
Standard reference: RSOS 2021 D-9.02.01P
An equipment skid is ready to lift, but loose bolts and a timber offcut remain on its upper frame. What must be done before tensioning the rigging?
Answer: Remove or positively secure the loose objects before lifting.
Items resting on the load can fall as it moves or tilts. Checking the load for loose debris prevents a falling-object hazard independently of the sling capacity.
Exam trap: A level trial lift cannot guarantee that loose items will stay in place during later movement.
Standard reference: RSOS 2021 D-10.02.04P
A lift plan requires 0.15 m clearance on each side of a 3.0 m wide skid passing through a pipe rack. The measured opening is 3.2 m. Is the planned route acceptable?
Answer: No. The route needs at least 3.30 m; revise the engineered route or geometry before lifting.
The required opening is 3.0 + 0.15 + 0.15 = 3.30 m. The measured opening is 0.10 m too narrow even though the skid itself physically fits.
Exam trap: Using only one 0.15 m allowance ignores the required clearance on the other side.
Standard reference: RSOS 2021 E-11.01.02P
A crane setup will block the only ambulance route into an operating site. Which risk control must be settled before approving that setup?
Answer: Provide an agreed, usable emergency-access route or change the crane location.
Risk evaluation includes how crane work affects site access. An emergency route must remain effective throughout assembly and lifting, rather than depend on dismantling a working crane.
Exam trap: Promising to retract the outriggers during an emergency cannot provide immediate reliable access.
Standard reference: RSOS 2021 E-11.02.03P
A crane can reach the load from its marked position, but one outrigger would extend into a required pedestrian escape corridor. What positioning issue must be resolved before deploying the outriggers?
Answer: Revise the crane orientation or approved location so the full support footprint leaves the escape corridor usable.
Crane orientation must accommodate the outriggers as well as the load path. A boom that can reach the load does not prove the crane footprint fits the usable site.
Exam trap: Shortening that outrigger without an approved configuration changes the planned support geometry.
Standard reference: RSOS 2021 E-12.02.04P
Why must the component delivery inventory be checked before beginning crane assembly?
Answer: To confirm the required components arrived and identify transport damage before those components are used.
Assembly depends on having the specified, serviceable components. A delivery receipt does not establish that each required item is present and undamaged.
Exam trap: Counting trailers alone does not verify the contents or their condition.
Standard reference: RSOS 2021 F-13.02.02P
Why are hydraulic fitting faces cleaned before connecting a removable outrigger box?
Answer: To prevent contamination entering the hydraulic circuit during assembly.
Particles carried into an opened connection can damage close-clearance hydraulic components. Cleaning must happen before joining the faces.
Exam trap: Wiping only the outside after coupling cannot remove dirt already introduced into the circuit.
Standard reference: RSOS 2021 F-15.03.03P
What holds a conventionally mounted telescopic main boom at its angle after the boom launcher support is removed?
Answer: The securely connected boom-hoist cylinder acting between the boom and upperworks.
The heel connection is a pivot. The boom-hoist cylinder supports and controls the boom angle, so launcher release requires the specified structural connections to be complete.
Exam trap: A heel pivot pin alone does not prevent the boom from rotating downward.
Standard reference: RSOS 2021 F-16.04.01L
A new scaffold intrudes into a previously clear slewing sector. The crane's configuration is unchanged. What electronic limit must be reassessed before work resumes?
Answer: The programmed working-range boundary for the new obstruction.
A range limiter represents the permitted operating envelope. A new obstruction changes that envelope even when boom, counterweight and capacity data remain unchanged.
Exam trap: Keeping the old range limits because the capacity chart is unchanged leaves the scaffold inside the permitted movement area.
Standard reference: RSOS 2021 G-18.01.04P; G-18.01.05P
A hydraulic lattice crawler's upperworks are slewed 180 degrees from the carrier's marked forward direction. Before travelling, how should the operator establish which track-control command moves toward the intended exit?
Answer: Confirm carrier orientation and the manufacturer's travel-control direction convention.
Cab facing direction can differ from the crawler frame's forward reference. Identifying the carrier reference prevents an unintended movement when the upperworks are reversed.
Exam trap: Assuming that pushing forward always moves toward the cab's view can send the crane in the opposite direction.
Standard reference: RSOS 2021 G-20.01.06P
What does side loading of a crane boom mean?
Answer: A force acting across the boom rather than in its intended vertical lifting plane.
Dragging a load or restraining it sideways can bend the boom laterally. A crane's normal lifting rating does not make it suitable for arbitrary transverse forces.
Exam trap: A large vertical hook load is not itself side loading; the direction of the force is the distinction.
Standard reference: RSOS 2021 G-20.02.01L
What is the operating purpose of a telescopic crane's suspension-height adjustment when negotiating an approved site access route?
Answer: To obtain the required carrier clearance within the manufacturer's travel limits.
Suspension height can change clearance beneath the carrier. The permitted setting remains governed by travel instructions and the route conditions.
Exam trap: Raising the suspension is not a method of increasing the crane's lifting capacity.
Standard reference: RSOS 2021 G-21.02.08P
A crane will be unattended briefly beside a vehicle route. The load is grounded, but its empty hook hangs in the vehicle clearance envelope. What needs changing before the operator leaves?
Answer: Place the boom and empty hook in a safe parked position clear of the route.
Securing the lifted load does not remove an empty-hook collision hazard. The unattended operating envelope must suit ongoing site traffic.
Exam trap: Locking the cab prevents unauthorized use but does not remove the hook from the vehicle path.
Standard reference: RSOS 2021 G-23.01.02P