Pass Your Red Seal

Boilermaker Flashcards

Online Red Seal Exam Preparation, built on official standards
FlashcardsSet 1 · Card 55 of 12055% to goTry 20 flashcards

Cards by block

In each set of 120
  • ACommon occupational skills31 cards
  • BRigging and hoisting36 cards
  • CCompletes new construction27 cards
  • DRepairs, maintenance, upgrading and testing26 cards
  • 78%Set 2 · 120 cards · 94 known
  • 72%Set 2 · 120 cards · 86 known

What is on a card

A-1.02Block A · Critical thinking

Two entrants on airline respirators draw from two manifolded breathing-air cylinders, each holding 8.5 m³ of free air at a full 15 300 kPa. Both read 9 000 kPa; there are no spares. The plan allows 50 L/min per entrant, and exit must start with 20 min of air left. How much longer can they work?

Answer
80 minutes: the cylinders hold 10 000 L, enough for 100 min at 100 L/min, less the 20 min exit reserve.
Why
Free air in a cylinder is proportional to its pressure: 8.5 m³ × 9 000/15 300 = 5.0 m³ each; 2 × 5.0 = 10.0 m³ = 10 000 L. Demand: 2 × 50 = 100 L/min, so 10 000 ÷ 100 = 100 min. Holding back the 20 min reserve leaves 80 min. Whoever monitors the supply calls the exit at that point, or sooner if consumption rises.
Exam trap
150 minutes, from the rated 17 m³: at 9 000 kPa the cylinders are only 59% full, so the full-cylinder volume overstates the air available.

From the Boilermaker standard: RSOS 2016 A-1.02.14P

Browse the 20 free cards and explanations

Two entrants on airline respirators draw from two manifolded breathing-air cylinders, each holding 8.5 m³ of free air at a full 15 300 kPa. Both read 9 000 kPa; there are no spares. The plan allows 50 L/min per entrant, and exit must start with 20 min of air left. How much longer can they work?

Answer: 80 minutes: the cylinders hold 10 000 L, enough for 100 min at 100 L/min, less the 20 min exit reserve.

Free air in a cylinder is proportional to its pressure: 8.5 m³ × 9 000/15 300 = 5.0 m³ each; 2 × 5.0 = 10.0 m³ = 10 000 L. Demand: 2 × 50 = 100 L/min, so 10 000 ÷ 100 = 100 min. Holding back the 20 min reserve leaves 80 min. Whoever monitors the supply calls the exit at that point, or sooner if consumption rises.

Exam trap: 150 minutes, from the rated 17 m³: at 9 000 kPa the cylinders are only 59% full, so the full-cylinder volume overstates the air available.

Standard reference: RSOS 2016 A-1.02.14P

Four 10 mm (3/8 in.) holes are needed in 13 mm (1/2 in.) mild steel flat bar. The ironworker is rated to punch 13 mm plate and has a 10 mm punch with its matching die. How should the holes be made?

Answer: Drill them: a punch smaller in diameter than the material thickness is overloaded and can break.

Punching force rises with plate thickness, while a punch's strength depends on its diameter. For mild steel, ironworker makers limit the hole to no smaller than the material thickness. A 10 mm punch in 13 mm bar is overstressed and can snap or shatter, throwing fragments. The 13 mm rating assumes a hole at least that diameter, so these holes are drilled.

Exam trap: Punch them because the machine is rated for 13 mm plate: that rating assumes a punch diameter at least equal to the thickness, which a 10 mm punch is not.

Standard reference: RSOS 2016 A-2.03.01L

On an outage schedule, which chain of activities sets the shortest possible completion time, and what happens if an activity on that chain slips?

Answer: The critical path, the longest chain of dependent activities, with no float; any delay on it delays the whole outage by the same amount.

Scheduling tools such as bar charts and network diagrams show each activity's duration and dependencies. The longest dependent chain fixes the earliest finish; activities off it have float and can slip somewhat without moving the end date. Planners therefore protect critical-path work first with labour, equipment and materials.

Exam trap: The activity with the most labour hours: a large task with float can slip without moving completion; only critical-path activities set the finish date.

Standard reference: RSOS 2016 A-3.01.01L

At the morning safety meeting, a crew lead learns that a new exclusion zone has been set under a boiler roof where tube panels will be lifted all shift. Two welders on the crew missed the meeting. What should the lead do before they start work?

Answer: Brief both welders in person on the exclusion zone, confirm they understood it, and add them to the meeting sign-off before they start.

Safety meeting information protects only the people who receive and understand it. The lead who attended relays the change to anyone absent, verifies understanding (for example, by asking them to describe where the zone is and why), and documents it, because the sign-off record shows the information reached the whole crew.

Exam trap: Posting the minutes on the trailer board is not enough: nothing confirms the welders read or understood the change before they walk under the lift.

Standard reference: RSOS 2016 A-4.01.06P

Along part of a butt seam between two 10 mm (3/8 in.) plates, one plate edge stands 3 mm (1/8 in.) above the other. A dog and wedge will bring the edges flush. To which plate is the dog tacked, and where does the wedge bear?

Answer: Tack the dog to the low plate with its end over the high plate, and drive the wedge between the dog and the high plate.

A wedge driven under an overhanging dog pushes apart the dog and the plate it bears on. Tacked to the low plate and bearing on the high plate, the wedge forces the high edge down and lifts the dog, and with it the low edge, until the seam is flush. Remove the dog afterwards as the specification requires.

Exam trap: Tacking the dog to the high plate and wedging against the low plate pushes the low edge further down, so the step grows instead of closing.

Standard reference: RSOS 2016 A-5.03.01P

With no plate-weight chart at hand, steel plate weights are worked out from area and thickness. What does one square foot (0.093 m²) of carbon steel plate 1 in. (25.4 mm) thick weigh?

Answer: About 40.8 lb (18.5 kg), so plate weight (lb) = area (ft²) × thickness (in.) × 40.8.

Weight = volume × unit weight. Carbon steel weighs about 490 lb/ft³ (7 850 kg/m³), and 1 ft² of plate 1 in. thick is 1/12 ft³: 490 ÷ 12 = 40.8 lb. A 4 × 8 ft sheet of 1/2 in. plate: 4 × 8 = 32 ft²; 32 × 0.5 × 40.8 = 653 lb (about 296 kg). Metric factor: 7.85 kg per m² per mm. If a drawing or exam question supplies a rounded figure, such as 40 lb/ft² per inch, use it.

Exam trap: 490 lb, the weight of a whole cubic foot of steel: a square foot 1 in. thick is only 1/12 of a cubic foot, so using 490 makes every plate 12 times too heavy.

Standard reference: RSOS 2016 B-6.01.02L

A polyester round sling's tag lists vertical 8 400 lb, choker 6 700 lb and vertical basket 16 800 lb. It will cradle a 15 000 lb pipe spool in a basket hitch with both legs at 60° from horizontal; the spool diameter meets the maker's minimum. Is the sling adequate?

Answer: No: at 60° the basket capacity is 16 800 × 0.866 = about 14 550 lb, below the 15 000 lb load.

A tag's vertical basket rating assumes both legs hang straight up. Multiply it by the sine of the leg angle from horizontal: 16 800 × sin 60° = 16 800 × 0.866 = 14 549 lb. That is less than 15 000 lb, so use a larger sling or rig the legs closer to vertical.

Exam trap: Yes, using the 16 800 lb vertical basket rating: that rating applies only with vertical legs; at 60° the capacity drops to about 14 550 lb.

Standard reference: RSOS 2016 B-6.03.03L

A 3/4 in. (19 mm) wire rope sling is checked against site criteria: remove at 10 random broken wires in one lay, 5 in one strand in one lay, or diameter loss over 5% of nominal. One lay has 7 random breaks, 3 in one strand, and one spot gauges 0.70 in. What is the disposition?

Answer: Remove it from service: the 0.70 in. spot is 6.7% under nominal, past the 5% limit, even though both broken-wire counts are acceptable.

Each removal criterion stands alone. Broken wires: 7 < 10 per lay and 3 < 5 per strand, both acceptable. Diameter: (0.75 − 0.70) ÷ 0.75 = 0.067, a 6.7% loss, over 5%. Localized diameter loss points to core failure, crushing or internal wear that broken-wire counts do not reveal.

Exam trap: Keep it because both broken-wire counts are under their limits: passing one criterion never offsets failing another, and the diameter loss alone condemns it.

Standard reference: RSOS 2016 B-7.01.02P

A vessel section will be set near an energized 25 kV line, with the crane staying outside the regulated limit of approach. What kind of tag line should be attached to the load?

Answer: A clean, dry synthetic-fibre rope such as polypropylene, which resists conducting, tied to the load itself.

If the load or hoist line contacts or arcs to the conductor, the tag line becomes the path to the worker holding it. Clean, dry synthetic fibre resists carrying current; wire rope, chain and wet or dirty natural fibre conduct. It is not rated insulation, so the limit of approach still governs. Tie it to the load to control rotation.

Exam trap: A manila tag line: natural fibre absorbs moisture and dirt that make it conductive, so it protects the handler far less than a clean, dry synthetic line.

Standard reference: RSOS 2016 B-7.03.05P

When new wire rope is spooled onto a tugger or crane drum, why must the first layers be wound tightly under back tension rather than loosely?

Answer: Loose lower layers let the loaded upper wraps cut down into them, crushing the rope and causing erratic spooling and sudden load drops.

Under load, outer wraps press hard on the layers below. Lower layers wound tight under tension (for example from a braked supply reel, as the rope or equipment maker specifies) form a firm base. Slack wraps shift and open gaps, so the loaded rope wedges between them, crushes strands and can jerk free under load.

Exam trap: To fit more rope on the drum; the gain in capacity is minor. The reason is protecting the rope from crushing and the load from wraps that pull through and drop.

Standard reference: RSOS 2016 B-8.02.01P

A heat-exchanger bundle was lifted out through a platform opening made by removing two grating panels and a handrail section. The crane has left, and the grating is laid back but not clipped. A crew wants the barricade around the opening removed. What must happen first?

Answer: Clip and secure the grating and reinstall the handrail; then remove the barricade and tell affected crews the area is clear.

Post-lift hazards are eliminated before an area is reopened: removed grating, handrail and toe boards are reinstated and fastened, and loose material is cleared. Unclipped grating can shift or tip underfoot. Only then are the barriers removed, which is how others are advised the area is clear.

Exam trap: Removing the barricade because the panels are back in place: unclipped grating can shift off its supports, and the missing handrail section still leaves an open edge.

Standard reference: RSOS 2016 B-9.01.05P

Which pattern-development method is used to lay out a rectangle-to-round duct transition?

Answer: Triangulation.

A rectangle-to-round transition has no single apex and no parallel surface lines. Triangulation divides the surface into small triangles, finds each line's true length from its plan length and the height, and builds the pattern triangle by triangle. Parallel-line development suits cylinders and prisms; radial-line suits right cones and pyramids.

Exam trap: Radial-line development needs every surface line to run to one apex, as on a right cone; the corners and round end of this transition do not share an apex.

Standard reference: RSOS 2016 C-10.01.01L

A platform frame laid out 8 ft × 12 ft is clamped on the layout table. Its diagonals measure 14 ft 5 1/4 in. and 14 ft 4 7/8 in. What correction squares it, and what should both diagonals then read?

Answer: Draw the corners of the long diagonal together until both diagonals read 14 ft 5 1/16 in.

A rectangle is square only when its diagonals are equal. True diagonal = √(8² + 12²) = √208 = 14.422 ft = 14 ft 5 1/16 in., which is also the average of the two readings. Pulling across the long diagonal (come-along or clamp) shortens it and lengthens the short one until both read 14 ft 5 1/16 in.

Exam trap: Pulling across the short diagonal shortens it further and pushes the frame more out of square; the force goes on the long diagonal.

Standard reference: RSOS 2016 C-10.04.02P

A horizontal hot-service vessel is aligned cold. Its support drawing shows one saddle with round anchor holes and the other with longitudinal slots. The crew proposes welding fitted washers over the slots and clamping both bases solid. What installation function must be preserved?

Answer: The slotted saddle must retain its designed longitudinal sliding movement; use the approved hold-down detail without locking the slots.

In this fixed/sliding support arrangement, one saddle locates the vessel while the other accommodates axial thermal growth. Locking both ends restrains that growth and transfers unwanted force into the shell and supports. Preserve the specified sliding and hold-down detail rather than improvising bolt clearance.

Exam trap: Treating the slots only as erection tolerance and welding them closed defeats thermal movement even though the vessel is correctly aligned when cold.

Standard reference: RSOS 2016 C-11.01.03P

A manway cover hung on a davit of a vertical vessel will not stay where it is released; it always swings back to the same position. What fitting error causes this, and what is the fix?

Answer: The davit's pivot axis is not plumb; re-set the davit socket or hinge so the axis is plumb in two directions.

If the pivot axis tilts, the arm's swing path is inclined and the cover's weight carries it to the low point of that path, so it always returns to one position. With the axis plumb, the swing is level, gravity has no pull along the path, and the cover stays where it is placed. Plumb is checked in two directions 90° apart.

Exam trap: Tightening the hinge to add friction only hides the fault and makes the cover hard to swing; the axis is still out of plumb.

Standard reference: RSOS 2016 C-11.02.02P

A 2.000 in. OD tube with a measured 1.730 in. ID (0.135 in. wall) is to be rolled into a 2.012 in. hole. The procedure calls for 7 % wall reduction applied to both walls. To what expanded ID should the tube be rolled?

Answer: 1.761 in. (44.73 mm).

Expanded ID = clearance + tube wall reduction + original ID. Clearance = 2.012 − 2.000 = 0.012 in. Reduction = 0.07 × (2 × 0.135) = 0.0189 in. Expanded ID = 0.012 + 0.0189 + 1.730 = 1.7609 in. After rolling, measure the ID with a telescoping gauge and micrometer and compare.

Exam trap: Applying 7 % to one wall (0.0095 in.) gives 1.751 in. and an under-rolled joint; the ID grows by the thinning of both walls.

Standard reference: RSOS 2016 C-12.02.02L

Why is an arc strike on a pressure-vessel shell, outside any weld groove, treated as a defect to be reported and repaired rather than as a cosmetic mark?

Answer: The arc melts and rapidly quenches a small spot, leaving hard, brittle metal that may contain cracks and acts as a stress raiser where cracks can start.

The cold shell quenches the tiny melted spot, forming hardened heat-affected metal, often with micro-cracks or porosity. Under pressure and thermal cycles this notch can start fatigue or brittle cracking. Arc strikes are recorded, removed by grinding as the procedure allows and checked by magnetic particle or penetrant testing; deeper ones need an approved weld repair.

Exam trap: Ignoring it because no measurable metal was lost: the harm is metallurgical (a hardened, possibly cracked spot), not missing thickness.

Standard reference: RSOS 2016 D-13.01.03P

A replacement metal-bellows expansion joint for a fly-ash-laden flue-gas duct has an internal flow liner welded at one end only. How is the joint oriented when it is fitted?

Answer: With the liner's welded (fixed) end upstream and its free end pointing downstream, matching the flow arrow on the joint.

The liner shields the thin bellows convolutions from erosive, turbulent gas. Fixed upstream, gas slides along the liner and past its free lip. Installed backward, gas and ash ram into the open lip, packing the convolutions with ash and shaking the liner, which wears and cracks the bellows. The flow arrow and the drawing govern orientation.

Exam trap: Fitting the welded end downstream so gas pushes the liner onto its weld: the free lip then faces into the flow, which drives ash under it into the convolutions and makes the liner flutter.

Standard reference: RSOS 2016 D-13.03.03P

Visual inspection of a reinstalled exchanger channel cover finds every stud protruding two threads past its nut, all nuts stamped 2H, and one stud with no grade marking. Which finding rejects the joint, and what is done?

Answer: The unmarked stud: unidentified hardware cannot be verified as the specified grade, so it is replaced with a correctly marked stud of that grade.

Visual testing confirms hardware is complete, identified and fully engaged. Two threads beyond the nut is the normal allowance (as in the bolt-length rule) and shows full engagement; 2H is the heavy hex nut grade used with alloy studs. A stud with no grade mark could be low-strength steel, so it is rejected, not accepted on looks.

Exam trap: Rejecting the protruding threads: two threads past the nut is the intended allowance and proves full nut engagement.

Standard reference: RSOS 2016 D-13.05.02P

About 30 t of broken firebrick (bulk density 1 600 kg/m³) must be hauled away in 10 m³ roll-off bins. The hauler limits each bin to 8 t of material. How many bin loads are needed, and how full can each bin be?

Answer: 4 loads, with no bin filled past 5 m³ (half full), which keeps each load within the 8 t limit.

Plan by whichever limit governs. A full bin would hold 10 m³ × 1 600 kg/m³ = 16 t, double the 8 t limit, so weight governs. 8 t ÷ 1.6 t/m³ = 5 m³ per bin; 30 t ÷ 8 t = 3.75, rounded up to 4 loads.

Exam trap: 2 bins, from 30 ÷ 1.6 = 18.75 m³ ÷ 10 m³; a bin filled by volume holds 10 m³ × 1.6 t/m³ = 16 t, twice the hauler's 8 t limit.

Standard reference: RSOS 2016 D-14.02.01P

20 free cardsCards 1 to 20 · no account needed