Truck and Transport Mechanic Flashcards
Online Red Seal Exam Preparation, built on official standardsCards from
Blocks
How many cards
Card order
Show
135 cards selectedof 135
Set 1
In progress43known18to review again74not marked
Set 2
Finished twice105known30to review again0not marked
Cards by block
In each set of 135- ACommon occupational skills8 cards
- BServices, diagnoses and repairs engines and supporting systems21 cards
- CServices, diagnoses and repairs air systems and brake systems17 cards
- DServices, diagnoses and repairs electrical and electronic systems22 cards
- EServices, diagnoses and repairs drive trains17 cards
- FServices, diagnoses and repairs steering, chassis/frames, suspensions, tires, wheels and hubs18 cards
- GServices, diagnoses and repairs cabs5 cards
- HServices, diagnoses and repairs trailers8 cards
- IServices, diagnoses and repairs climate control systems7 cards
- JServices, diagnoses and repairs hydraulic systems8 cards
- KServices, diagnoses and repairs hybrid and electric vehicles (EV)4 cards
Recent sessions
All sessions in Progress- 78%Set 2 · 135 cards · 105 known
- 72%Set 2 · 135 cards · 97 known
What is on a card
A-2.02Block A · Critical thinking
A hydraulic press is rated at 20 tonnes, but its approved work fixture is tagged 10 tonnes. A job needs 15 tonnes, and the press operates normally. Can that equipment setup be used?
- Answer
- No. The 10-tonne fixture limits this setup; a 15-tonne job exceeds its rating.
- Why
- The equipment setup must respect every load-bearing component's rating. A normally operating 20-tonne press does not increase the approved fixture's 10-tonne capacity.
- Exam trap
- Accepting the job from the press rating alone overlooks the weaker rated fixture.
From the Truck and Transport Mechanic standard: RSOS 2022 A-2.02.02P
Cards from
Blocks
How many cards
Show
135 cards selectedof 135
Sources
- Truck and Transport Mechanic RSOS 2022Red Seal Program · FreeOpen
Blocks
- ACommon occupational skills
- BServices, diagnoses and repairs engines and supporting systems
- CServices, diagnoses and repairs air systems and brake systems
- DServices, diagnoses and repairs electrical and electronic systems
- EServices, diagnoses and repairs drive trains
- FServices, diagnoses and repairs steering, chassis/frames, suspensions, tires, wheels and hubs
- GServices, diagnoses and repairs cabs
- HServices, diagnoses and repairs trailers
- IServices, diagnoses and repairs climate control systems
- JServices, diagnoses and repairs hydraulic systems
- KServices, diagnoses and repairs hybrid and electric vehicles (EV)
A-2.02Block A · task 2 · sub-task 2
Flashcards for every tradeBrowse the 20 free cards and explanations
A hydraulic press is rated at 20 tonnes, but its approved work fixture is tagged 10 tonnes. A job needs 15 tonnes, and the press operates normally. Can that equipment setup be used?
Answer: No. The 10-tonne fixture limits this setup; a 15-tonne job exceeds its rating.
The equipment setup must respect every load-bearing component's rating. A normally operating 20-tonne press does not increase the approved fixture's 10-tonne capacity.
Exam trap: Accepting the job from the press rating alone overlooks the weaker rated fixture.
Standard reference: RSOS 2022 A-2.02.02P
A replacement full-flow oil filter fits the mount. Its bypass opens at 30 kPa differential, but the engine specifies 170 kPa. Main oil pressure is normal. Does that pressure reading justify keeping this filter?
Answer: No. Fit the specified filter; normal main pressure does not validate its wrong bypass setting.
The bypass responds to differential pressure across the filter, not just main gallery pressure. A 30 kPa opening setting does not meet the stated 170 kPa requirement even when the main pressure reading is normal.
Exam trap: Keeping it because pressure is normal confuses oil delivery pressure with filter bypass compatibility.
Standard reference: RSOS 2022 B-6.01.05P; B-6.01.06P
A PTO truck shuts down after five minutes of stationary work. The idle-shutdown timer is enabled, PTO operation otherwise tests normally, and the OEM supports a PTO-active exception. What parameter service meets the work requirement?
Answer: Configure the OEM-supported PTO-active exception to the idle-shutdown timer.
The timed shutdown matches the enabled idle timer while PTO hardware operates normally. The supported exception can retain ordinary idle control while allowing the required stationary PTO work.
Exam trap: Replacing PTO hardware ignores its normal test and the matching shutdown-timer condition.
Standard reference: RSOS 2022 B-9.01.02P
An engine retarder activates when the accelerator is released and its ECM commands that response. All stages pass tests, but the fleet requires pedal-only activation, which the OEM supports. What service focus is appropriate?
Answer: Set the supported ECM retarder activation mode to the fleet's pedal-only requirement.
The retarder follows its existing coast-release command and the stages work. The complaint is therefore the configured activation behavior; select the supported mode required by the fleet.
Exam trap: Adjusting mechanical lash cannot change when the ECM issues a valid activation command.
Standard reference: RSOS 2022 B-11.01.03P
A dash air gauge reads 850 kPa. Two calibrated reference gauges each read 650 kPa at the same reservoir port under stable pressure. What should be corrected before using the dash reading to adjust the governor?
Answer: Correct the dash gauge indication before making governor adjustments from it.
Independent calibrated readings agree at the same port while pressure is stable. That evidence supports an inaccurate dash indication rather than a real 850 kPa reservoir pressure.
Exam trap: Adjust the governor to suit the dash reading; two agreeing calibrated references show that indication is unreliable.
Standard reference: RSOS 2022 C-13.01.03P; C-13.01.02P
A removed spring-brake chamber is mechanically caged and awaiting disposal. What disposal procedure is still required before it enters the scrap stream?
Answer: Follow the manufacturer's approved disarming and disposal process.
Mechanical caging restrains the spring for handling; it does not by itself make the stored-energy assembly ordinary scrap. The prescribed disposal route must control that spring energy.
Exam trap: Send the caged chamber to general scrap; caging restrains spring energy and does not complete approved disarming/disposal.
Standard reference: RSOS 2022 C-13.03.07P
With the brake pedal released, a front hose has zero pressure at its inlet but 800 kPa at its outlet. Opening the caliper bleeder releases the drag, and the caliper moves freely. What fault is indicated?
Answer: An internal restriction in the brake hose is trapping pressure on the caliper side.
Pressure is released upstream but remains downstream of the hose. Bleeding that pressure frees a mechanically mobile caliper, supporting a hydraulic restriction rather than caliper seizure.
Exam trap: Replace the dragging caliper; it moves freely once trapped downstream pressure is released, while hose inlet pressure is already zero.
Standard reference: RSOS 2022 C-14.02.06P; C-14.02.10P
An air-cooled alternator's fins and air passages are packed with debris. Drive tension and battery tests pass, but output falls as alternator temperature rises. What service action should precede condemning it?
Answer: Clean the alternator's cooling fins and air passages by the approved procedure, then recheck hot performance.
The blocked cooling path is a service defect relevant to the temperature-related output loss. Passing drive and battery checks makes cleanup and retesting justified before condemning the unit.
Exam trap: Replace the alternator immediately; blocked cooling is an observed service defect that must be corrected before judging hot performance.
Standard reference: RSOS 2022 D-16.01.03P; D-16.01.02L
Starter current draw and cranking speed meet specifications. The B+ terminal's insulating bushing is cracked and the terminal moves against the case. Can the starting system be accepted after service?
Answer: No. Correct the damaged terminal insulation and securement before acceptance.
Normal current and speed do not demonstrate intact electrical isolation. A mobile B+ terminal with a cracked insulator can short against the starter case.
Exam trap: Accept passing current and speed; those results do not cancel damaged B+ isolation that permits contact with the case.
Standard reference: RSOS 2022 D-18.01.02P
A software bulletin applies to engine family X. This truck has family Y, although its ECM connector and case match the pictured module. What must be established before applying the update?
Answer: Confirm that the bulletin and software package are approved for this truck's exact vehicle and ECM configuration.
Housing and connector resemblance do not establish software applicability. Verify identifiers and bulletin scope before selecting an update; family X eligibility does not establish family Y eligibility.
Exam trap: Flash by connector resemblance; matching hardware appearance does not establish the bulletin's engine-family eligibility.
Standard reference: RSOS 2022 D-20.01.04P
A newly installed PTO has 0.36 mm gear backlash. This installation requires 0.15–0.25 mm. By how much must backlash decrease at minimum to enter the permitted range?
Answer: At least 0.11 mm: 0.36 − 0.25 = 0.11 mm.
The first permitted value reached by reducing 0.36 mm is the upper limit of 0.25 mm. Adjust using the specified PTO method and verify the final backlash remains within 0.15–0.25 mm.
Exam trap: Reducing by 0.21 mm uses the lower limit; the minimum requested decrease only needs to reach the upper limit, 0.25 mm.
Standard reference: RSOS 2022 E-22.03.06P (PTO installation and backlash).
A driveshaft has vertical inclination and lateral offset. Before comparing a universal-joint operating angle with the OEM limit, what measurement approach is required?
Answer: Measure both vertical and horizontal contributions and determine the full compound operating angle by the approved method.
The angle between the connected shaft axes includes both planes. Determine the full compound operating angle using the specified method before comparing it with the OEM limit.
Exam trap: Ignoring lateral offset omits a contribution to the angle between shaft axes; the vertical reading covers only one plane.
Standard reference: RSOS 2022 E-25.02.06P (driveline angles); E-25.02.01L (operation).
An OEM kingpin-bushing test requires radial knuckle movement relative to the axle beam. The dial-indicator base is fixed to the beam. Where should its contact be placed, and in what direction?
Answer: Place the contact on the knuckle, aligned with the specified radial movement relative to the axle beam.
That setup reads knuckle movement relative to the beam. Use the OEM support and loading method so the reading represents the intended kingpin-bushing movement.
Exam trap: Putting the contact on the beam along with its base cannot measure knuckle movement relative to that beam.
Standard reference: RSOS 2022 F-28.02.02P, F-28.02.06P.
An air suspension sits low. A misplaced cable tie holds the height-valve linkage in exhaust. With the tie removed, hand operation gives normal filling and height; the air springs pass the specified leak test. What should the service correction target?
Answer: Correct the cable-tie interference and restore free, properly routed height-valve linkage.
The tie physically holds the valve in exhaust. Normal filling after release and passing air-spring leak tests support removing that interference before replacing or resetting sound components.
Exam trap: Resetting valve height ignores the tie holding its linkage in exhaust; normal filling after freeing it and tight springs point to interference.
Standard reference: RSOS 2022 F-30.01.03P, F-30.01.06P.
A fleet requires at least 4.0 mm tread depth at every specified measurement location. Readings are 3.8, 6.0 and 6.2 mm. Does this tire meet that fleet requirement?
Answer: No. The 3.8 mm reading fails the required 4.0 mm minimum at a specified location.
The rule applies to every required location, not the average. The two deeper readings do not cancel the one below the fleet's stated minimum.
Exam trap: Averaging the three depths cannot satisfy a minimum at every location; the 3.8 mm reading fails the stated 4.0 mm rule.
Standard reference: RSOS 2022 F-32.01.03P (tread-depth and pressure measurement).
What training must a mechanic have before repairing a manufacturer's supplemental restraint system?
Answer: The manufacturer-required training for repairing that SRS.
SRS repair has specific explosive stored-energy hazards and manufacturer procedures. The standard identifies manufacturer training requirements separately from general cab repair skills.
Exam trap: General electrical experience alone; it does not replace the manufacturer-required SRS repair training.
Standard reference: RSOS 2022 G-33.03.03L
Rain wets a trailer's upper front wall; its floor and lower panels stay dry. A controlled roof-seam water test reproduces the entry, while a front-wall test does not. Where should repair be directed?
Answer: The roof seam that reproduces the water entry.
The upper wet pattern agrees with the positive roof-seam test. The negative wall test narrows the repair target away from the front-wall joints.
Exam trap: Reseal the dry lower floor joints; their location and the negative lower-panel evidence do not explain upper entry.
Standard reference: RSOS 2022 H-35.02.03P; H-35.02.07P
An A/C condenser has insect debris packed between its fins. Which cleaning approach restores airflow without folding the fins over?
Answer: Use the approved gentle cleaning method, direction and pressure that protect the condenser fins.
Removing exterior debris restores the air passage needed for heat rejection. The cleaning method must avoid bending delicate fins, which would create another restriction.
Exam trap: Use maximum pressure close to the coil; folded fins can reduce airflow even after the insects are removed.
Standard reference: RSOS 2022 I-38.01.02P
In an approved isolated cylinder test, verified intake volume is 0.5 L over 3 s. The supply flowmeter stays at 5 L/min throughout; no other feed paths or accumulators are connected. Which measurement needs scrutiny before condemning the pump for low flow?
Answer: Check the supply flowmeter’s installation, units and calibration before accepting its low-flow reading.
Verified intake flow = 0.5 L ÷ 3 s × 60 s/min = 10 L/min. With no other feed or accumulator, that evidence conflicts with 5 L/min indicated throughout the stroke. Resolve the measurement conflict before diagnosing low pump delivery.
Exam trap: Condemn the pump from 5 L/min alone; the verified volume and stroke time demonstrate 10 L/min intake under this test.
Standard reference: RSOS 2022 J-39.02.06P; J-39.02.07P; J-39.02.08P
During an approved hybrid DC/DC converter test, input is 400 V at 2 A and output is 24 V at 25 A. Ignoring other energy paths, how much electrical power is lost between input and output?
Answer: 200 W.
Input power = 400 V × 2 A = 800 W. Output power = 24 V × 25 A = 600 W. With other energy paths excluded, the difference is 800 − 600 = 200 W lost. This calculation alone does not declare an efficiency fault without a model limit.
Exam trap: Treat the larger output current as an energy gain; power depends on both voltage and current, and the output voltage is much lower.
Standard reference: RSOS 2022 K-40.02.01L; K-40.02.06P