Pass Your Red Seal

Construction Craft Worker Flashcards

Online Red Seal Exam Preparation, built on official standards
FlashcardsSet 1 · Card 47 of 10054% to goTry 20 flashcards

Cards by block

In each set of 100
  • ACommon Occupational Skills23 cards
  • BSite Work19 cards
  • CScaffolding and Access Equipment9 cards
  • DConcrete Work18 cards
  • EMasonry Work10 cards
  • FUtilities and Pipeline11 cards
  • GRoadwork10 cards
  • 78%Set 2 · 100 cards · 78 known
  • 72%Set 2 · 100 cards · 72 known

What is on a card

A-1.01Block A · Recall

Why must hazardous stored energy be released or restrained as part of equipment lockout?

Answer
It can move components or injure workers after the power supply is isolated.
Why
Isolation stops new energy entering equipment. Pressure, elevated loads and spring force can remain stored and must be controlled before work begins.
Exam trap
An OFF switch does not discharge stored pressure or support a suspended component.

From the Construction Craft Worker standard: NOA 2015 A-1.01.10

Browse the 20 free cards and explanations

Why must hazardous stored energy be released or restrained as part of equipment lockout?

Answer: It can move components or injure workers after the power supply is isolated.

Isolation stops new energy entering equipment. Pressure, elevated loads and spring force can remain stored and must be controlled before work begins.

Exam trap: An OFF switch does not discharge stored pressure or support a suspended component.

Standard reference: NOA 2015 A-1.01.10

For the same load in a symmetrical two-leg sling, how does reducing each sling leg’s angle above horizontal affect leg tension?

Answer: It increases the tension in each sling leg.

Each leg must supply its share of the vertical lifting force. A shallower angle provides less vertical force per unit of tension, so leg tension rises.

Exam trap: Dividing the load by two ignores the additional tension caused by the sling angle.

Standard reference: NOA 2015 A-2 K10

What is the purpose of using agreed site reference directions when coordinating equipment movement?

Answer: They give all participants the same directional reference.

Workers facing opposite ways can interpret left and right differently. Agreed references relate the instruction to one shared orientation.

Exam trap: A louder instruction does not resolve different interpretations of its direction.

Standard reference: NOA 2015 A-3 K10

A 4.8 m × 2.4 m wall needs single-layer insulation. Boards cover 1.2 m × 0.6 m, with no openings. Allow 12.5% extra for cutting. How many whole boards are needed?

Answer: 18 boards.

Wall area is 4.8 × 2.4 = 11.52 m². Each board covers 0.72 m²; 11.52 ÷ 0.72 = 16. Adding 12.5% gives 16 × 1.125 = 18 boards.

Exam trap: Sixteen boards cover the net area but omit the stated cutting allowance.

Standard reference: NOA 2015 A-4.05.02

A piling cage’s main bars are correctly positioned, but tie-wire ends project into the specified concrete-cover zone. What must be corrected before placement?

Answer: Reposition the protruding tie-wire ends to preserve the required cover envelope.

The cage’s cover requirement includes projections that approach the hole wall. Correct main-bar alignment does not make projecting tie ends acceptable.

Exam trap: Ignoring tie wire because it is not a main reinforcing bar still leaves steel within the required clear cover.

Standard reference: NOA 2015 B-5.03.07

Why is the specified moisture range important when compacting granular backfill?

Answer: It helps particles rearrange under compactive effort to achieve the required density.

Suitable moisture assists particle movement during compaction. Too little or excessive water can prevent the material from reaching its specified compacted condition.

Exam trap: Adding more water is not always better; saturated fill can displace or pump instead of compacting.

Standard reference: NOA 2015 B-6 K13

After overnight cooling, a compressor’s air tools discharge water and the receiver’s daily service is overdue. What receiver maintenance is needed before further tool use?

Answer: Drain the receiver using the manufacturer’s safe condensate-removal procedure.

Water accumulates as compressed air cools. Removing it limits water carryover and internal corrosion while following the specified pressure-control precautions.

Exam trap: Increasing air pressure does not remove the water accumulated in the receiver.

Standard reference: NOA 2015 B-7.04.02

A gas detector fails its required bump test but displays zero gas in fresh air. What is required before it is used for the safety watch?

Answer: Take it out of use until it passes the specified functional check or is replaced.

A zero display does not prove a sensor responds to gas. The failed bump test means the detector’s ability to warn of exposure has not been established.

Exam trap: Resetting the display to zero does not repair an unresponsive sensor.

Standard reference: NOA 2015 B-9.01.02

Hardened concrete prevents a scaffold connector from seating fully. What must be done before the component is assembled?

Answer: Clean the connector and inspect it so it can engage correctly.

Debris can prevent full connector engagement and conceal damage. Cleaning restores the intended contact surfaces; inspection confirms the component remains usable.

Exam trap: Hammering the dirty connector into place can damage it without establishing proper engagement.

Standard reference: NOA 2015 C-10.03.02

A scissor lift must operate where loose fill covers a buried trench. What must be established before positioning the lift there?

Answer: That the ground can support the lift in the intended operating configuration.

A compact-looking surface can conceal weak support. Ground bearing must suit the loaded lift before the platform is positioned or raised.

Exam trap: A level surface alone does not establish adequate load-bearing capacity over a trench.

Standard reference: NOA 2015 C-11.02.01

An approved wall-form drawing tapers the clear thickness from 300 mm at the base to 280 mm at the top. Both measured dimensions match. Should the top be widened to 300 mm before placement?

Answer: No; retain the specified taper and verify the remainder of the form against the drawing.

The drawing requires two different thicknesses. The matching top measurement is a design feature, rather than a defect; making it equal to the base would alter the approved geometry.

Exam trap: Assuming every wall must have parallel faces would turn the correct tapered form into an incorrect installation.

Standard reference: NOA 2015 D-12.02.02

A trial concrete batch requires 80 kg total dry aggregate, with sand at 35% of that mass and coarse aggregate making up the balance. What aggregate quantities meet the batch sheet?

Answer: 28 kg sand and 52 kg coarse aggregate.

Sand = 80 × 0.35 = 28 kg. Coarse aggregate = 80 − 28 = 52 kg. The quantities total 80 kg and preserve the stated mass-based split.

Exam trap: Using 35 kg sand treats the percentage as a kilogram quantity and changes the batch’s specified grading proportions.

Standard reference: NOA 2015 D-13.01.02

Two slab bays share mix, thickness, placement time and heater output. Only the windward bay cools rapidly after gusts; enclosure air stays warm, but its tarp edge has lifted. What curing control should be investigated before increasing heat?

Answer: Wind entering the lifted tarp edge; restore the specified enclosure and monitor concrete temperatures.

Matched placement and heating conditions, cooling timed to gusts and the open edge point to local heat loss. Warm enclosure air does not establish concrete protection; restore the wind barrier and verify the concrete response.

Exam trap: Increasing heater output alone leaves the identified cold-air path open and may overheat the protected bay.

Standard reference: NOA 2015 D-13.06.03

What does specified non-shrink grout provide beneath a machine base after the base has been aligned?

Answer: Continuous load-bearing support between the base and its foundation.

The grout fills the space beneath the aligned base so operating loads can transfer to the foundation. Its placement must avoid voids and follow the selected product and engineered details.

Exam trap: Levelling shims establish alignment but leave unsupported spaces unless the specified grout fills them.

Standard reference: NOA 2015 D-15.01.03

Why is hardened mortar removed from the mixer before a new specified batch is prepared?

Answer: To prevent loose old lumps from contaminating the new batch and interfering with mixing.

Old deposits can detach into the fresh mortar and obstruct the intended mixing action. Prepare the mixer with the approved cleaning method before charging the new batch.

Exam trap: Adding the new batch over old deposits does not restore those lumps to fresh, uniformly mixed mortar.

Standard reference: NOA 2015 E-16.01.04

Why must an acidic masonry cleaner never be combined with chlorine bleach?

Answer: The mixture can release toxic chlorine gas.

Acid reacts with hypochlorite bleach and can liberate chlorine. Keep incompatible cleaners separate and follow the product SDS and mixing instructions.

Exam trap: Combining cleaners does not safely increase cleaning power; it creates a hazardous chemical reaction.

Standard reference: NOA 2015 E-17.03.02

A pipe-to-manhole detail uses a flexible connector to accommodate differential settlement. Filling its moving section solid with grout is proposed as extra sealing. What installation decision follows?

Answer: Keep the connector’s designed movement free and complete its specified watertight installation.

The connector must seal while allowing the movement provided by the detail. Rigid grout in its moving section defeats that function and can transfer settlement stress to the pipe or joint.

Exam trap: More grout is not extra protection if it locks the movement the specified connection was designed to accommodate.

Standard reference: NOA 2015 F-18.03.05

What does stringing pipe mean during pipeline construction?

Answer: Distributing individual pipe lengths along the right of way in the planned assembly sequence.

Stringing positions the pieces for joining at their intended locations, using the specified support and order. It connects the pipe inventory to the engineering layout along the route.

Exam trap: Stacking all pipe in one stockpile stores it, but does not distribute the lengths along their planned assembly route.

Standard reference: NOA 2015 F-19.02.03

Saw cutting has left slurry on sound asphalt patch edges. The repair procedure requires clean, dry edges before tack application. What preparation remains before applying the tack?

Answer: Remove the slurry and dry the edges using the approved preparation method.

Sound pavement still needs the specified clean bond surface. Slurry is a separate contamination and moisture problem that must be removed before the tack can contact the retained asphalt.

Exam trap: Coating over the slurry bonds to contamination rather than to the specified clean asphalt edge.

Standard reference: NOA 2015 G-20.02.04

How does a hot-applied thermoplastic road marking harden after application, unlike paint that dries by losing liquid carrier?

Answer: It hardens as the heated thermoplastic cools.

Thermoplastic is softened by heat for application and solidifies on cooling. Follow the material’s specified heating and installation limits; it does not depend on paint-like solvent evaporation.

Exam trap: Waiting for a liquid carrier to evaporate applies the wrong drying mechanism to a thermoplastic marking.

Standard reference: NOA 2015 G-21 K6

20 free cardsCards 1 to 20 · no account needed