Oil Heat System Technician Flashcards
Online Red Seal Exam Preparation, built on official standardsCards from
Blocks
How many cards
Card order
Show
110 cards selectedof 110
Set 1
In progress35known15to review again60not marked
Set 2
Finished twice86known24to review again0not marked
Cards by block
In each set of 110- ACommon occupational skills7 cards
- BInstalls fuel supply and storage systems20 cards
- CInstalls oil-fired heating systems23 cards
- DInstalls venting systems, and combustion air and make-up air equipment and components17 cards
- EInstalls and tests electrical and electronic systems22 cards
- FMaintenance, diagnosis, repair and removal21 cards
Recent sessions
All sessions in Progress- 78%Set 2 · 110 cards · 86 known
- 72%Set 2 · 110 cards · 79 known
What is on a card
A-2.01Block A · Application
A brass flare nut on a copper oil line is tight and starting to round under an open-ended wrench. Which hand tool grips more of its flats while still fitting over the tubing?
- Answer
- A correctly sized flare-nut wrench.
- Why
- A flare-nut wrench surrounds more of the nut than an open-ended wrench while its slot clears the tubing. Greater contact distributes turning force over more flats, reducing further rounding.
- Exam trap
- A pipe wrench grips with teeth and can damage or distort the brass fitting instead of preserving the flats.
From the Oil Heat System Technician standard: RSOS 2025 A-2.01.01P
Cards from
Blocks
How many cards
Show
110 cards selectedof 110
Sources
- Oil Heat System Technician RSOS 2025Red Seal Program · FreeOpen
- CSA B139 oil-burning equipment codeOpen
Blocks
- ACommon occupational skills
- BInstalls fuel supply and storage systems
- CInstalls oil-fired heating systems
- DInstalls venting systems, and combustion air and make-up air equipment and components
- EInstalls and tests electrical and electronic systems
- FMaintenance, diagnosis, repair and removal
A-2.01Block A · task 2 · sub-task 1
Flashcards for every tradeBrowse the 20 free cards and explanations
A brass flare nut on a copper oil line is tight and starting to round under an open-ended wrench. Which hand tool grips more of its flats while still fitting over the tubing?
Answer: A correctly sized flare-nut wrench.
A flare-nut wrench surrounds more of the nut than an open-ended wrench while its slot clears the tubing. Greater contact distributes turning force over more flats, reducing further rounding.
Exam trap: A pipe wrench grips with teeth and can damage or distort the brass fitting instead of preserving the flats.
Standard reference: RSOS 2025 A-2.01.01P
Which drawing view shows the internal construction exposed by an imaginary vertical cut through a building?
Answer: A section view.
A section represents an imagined cut through the building and shows internal relationships that exterior views conceal. Its cutting plane identifies where that view is taken.
Exam trap: An elevation shows a face of the building; it does not inherently expose construction along a cut plane.
Standard reference: RSOS 2025 A-3.01.01L
A tank valve with tapered pipe threads has passed its required handle orientation while being tightened. What should be done instead of backing off the joint to align it?
Answer: Disassemble and remake the tapered-thread connection with approved sealing and correct alignment.
Tapered threads seal through their fitted engagement with the specified sealing method. Backing off can disturb that engagement. Remaking the connection, with suitable fittings if needed, achieves alignment without leaving a loosened joint.
Exam trap: Forcing the valve farther around can overstress the fitting or tank connection; alignment does not justify excessive tightening.
Standard reference: RSOS 2025 B-6.04.03P
In a typical oil de-aerator arrangement, where does excess oil returning from the burner pump go instead of travelling back to the bulk tank?
Answer: It returns to the de-aerator for local recirculation to the pump.
The local loop receives the pump return, separates gas and supplies liquid back to the pump. The bulk-tank line makes up consumed fuel instead of carrying the full pump circulation back and forth.
Exam trap: Sending that return directly to the bulk tank describes a conventional two-line arrangement, not the local de-aerator loop.
Standard reference: RSOS 2025 B-7.01.01L
An oil inlet test plan must measure both positive gravity-feed pressure and suction when tank level falls below the pump. Which gauge type can display both conditions without changing instruments?
Answer: A compound pressure-and-vacuum gauge with suitable ranges.
The inlet can be above or below atmospheric pressure as the supply condition changes. A compound gauge spans both sides of zero, allowing positive head and suction to be assessed with one suitable instrument.
Exam trap: A positive-pressure-only gauge cannot reliably display the required suction reading.
Standard reference: RSOS 2025 B-7.01.02P
In a properly made flared oil-line joint, which surfaces form the fluid seal?
Answer: The tubing flare against the mating conical seat.
The nut supplies clamping force to the mating flare surfaces. Those surfaces form the fluid seal; sound geometry and proper assembly matter more than sealing the nut threads.
Exam trap: Applying sealant to the nut threads does not repair a cracked or distorted flare seat.
Standard reference: RSOS 2025 B-7.02.01L
A replacement burner uses an adjustable mounting flange. The old flange position fits the bolt pattern, but the replacement air tube is longer. What must be established before the burner is fastened?
Answer: Establish the approved air-tube insertion depth for the appliance and set the adjustable flange accordingly.
Bolt-pattern compatibility only locates the mounting holes. A longer air tube can project too far into the combustion chamber unless its flange is set from the appliance's required insertion reference.
Exam trap: Copying the old flange setting ignores the different tube length and can put the combustion head in the wrong position.
Standard reference: RSOS 2025 C-8.03.06P
Rectangular duct sections have S-cleats fitted to two opposite edges. How are the remaining flanged edges joined to complete the transverse connection?
Answer: Slide drive cleats over the remaining turned flanges and secure their ends as required.
S-cleats engage two opposing edges; drive cleats lock the other flanged edges of this transverse joint. The completed connection must mechanically engage the duct sections before its sealing detail is finished.
Exam trap: Sealing over unjoined flanges does not provide the mechanical connection made by the drive cleats.
Standard reference: RSOS 2025 C-9.01.02P
A new hydronic loop uses a cast-iron boiler and circulator. Domestic PEX of suitable diameter, temperature and pressure rating is offered. What additional tubing property protects those iron components?
Answer: Use tubing with the specified oxygen-diffusion barrier.
Oxygen can diffuse through unsuitable plastic tubing into the closed heating circuit and sustain corrosion of iron components. Temperature, pressure and size ratings do not address that oxygen permeability.
Exam trap: Assuming all domestic-water PEX suits a closed hydronic circuit overlooks its effect on ferrous components.
Standard reference: RSOS 2025 C-10.02.01L
An indirect heater coil branch rises above a hot boiler and its circulator stops between calls. What component prevents unwanted gravity circulation through that idle branch?
Answer: Install the designed spring-loaded check or hydronic flow-control valve that blocks unwanted thermosiphoning.
Hot water can rise through the elevated coil circuit even with its circulator stopped. The selected flow-control device resists gravity circulation while allowing the intended pumped flow when the tank calls for heat.
Exam trap: Assuming a stopped circulator blocks the pipe leaves a possible gravity-flow path through the idle branch.
Standard reference: RSOS 2025 C-10.03.05P
A new water heater is fed through a check valve. All taps close during recovery, and the design has no means to absorb increased water volume. What additional provision is needed on the tank side of the check valve?
Answer: Provide a correctly sized potable-water expansion tank or other approved thermal-expansion control on the closed tank side.
As the water heats, its volume increases. With taps closed and the check valve blocking return to the supply, the system needs a designed means of accepting that expansion without an excessive pressure rise.
Exam trap: Relying on the relief valve to discharge each recovery cycle uses emergency protection as normal expansion control.
Standard reference: RSOS 2025 C-10.04.03P
What produces natural draft in a warm chimney connected to an oil-fired appliance?
Answer: Buoyancy from the density difference between warm flue gases and cooler surrounding air produces draft.
The warmer, less-dense gas column rises and creates a pressure difference that draws flow through the connected appliance. Available natural draft depends on conditions such as effective height and gas temperature.
Exam trap: Attributing all natural draft to wind confuses a variable external influence with the buoyancy that drives a warm chimney.
Standard reference: RSOS 2025 D-11.01.01L
A barometric draft regulator is fitted to a horizontal oil flue connector, but its pivot axis slopes after the collar is secured. What mounting correction is needed before commissioning?
Answer: Reset the mounting so the regulator has its specified plumb orientation and level pivot axis.
The weighted regulator door depends on gravity acting about the intended pivot. A tilted mounting changes that balance and can impair its movement or draft response even if the collar is secure.
Exam trap: Changing the counterweight setting to compensate for a tilted pivot masks a mounting error and does not restore correct geometry.
Standard reference: RSOS 2025 D-11.03.02P
A make-up air heating coil is to operate in counterflow. At which air face of the coil should its hot-water supply enter?
Answer: Connect the hot-water supply at the leaving-air face, using the coil manufacturer's counterflow connections.
In counterflow, the hottest entering water meets the warmest leaving air, while cooler returning water meets the cold entering air. This preserves a useful temperature difference across the coil.
Exam trap: Connecting the hot supply at the entering-air face creates the opposite flow relationship and can reduce the intended coil performance.
Standard reference: RSOS 2025 D-12.03.04P
What is the purpose of vibration isolators between a make-up air fan and its structural support?
Answer: They reduce vibration transmitted from the operating fan into the supporting building structure.
Properly selected isolators carry the equipment load while limiting mechanical vibration transfer. Their installation must avoid rigid connections that bypass the isolation path.
Exam trap: Treating the isolators only as levelling pads overlooks the vibration path that rigidly bridged mounts can reintroduce.
Standard reference: RSOS 2025 D-12.04.01L
A fixed-temperature radiator system meets the design-day load but delivers unnecessarily hot water in mild weather. Room thermostats only switch zones on and off. Which water-temperature control strategy should be added to follow changing building heat loss?
Answer: Add outdoor reset control of the heating-water target.
Building heat loss generally falls as outdoor temperature rises. Outdoor reset lowers the water target in mild weather while retaining the higher target needed at design conditions; zone thermostats alone only enable or disable flow.
Exam trap: Lowering the fixed target permanently may reduce mild-weather overheating but leave inadequate output on the design day.
Standard reference: RSOS 2025 E-13.01.02P
A boiler demand input accepts only isolated contact closure. The zone panel provides a powered 24 V output. What interface lets that output call the boiler without applying voltage to its input?
Answer: A suitable 24 V coil isolation relay whose dry contacts connect to the boiler demand input.
The panel output energizes the relay coil. Its electrically separate contacts close the boiler demand circuit without transferring the panel’s 24 V into an input intended only for contact closure.
Exam trap: Connecting the powered output directly can damage or misoperate the boiler’s dry-contact input.
Standard reference: RSOS 2025 E-13.01.03P
An interrupted-ignition oil burner establishes flame and completes its ignition carryover interval. The heat call continues. What should happen to the ignition output now?
Answer: The ignition output should switch off while the established flame continues.
Interrupted ignition energizes the igniter for light-off and carryover, then removes ignition power once the flame is established. The continuing heat call still permits normal firing.
Exam trap: Keeping ignition energized throughout the run describes intermittent-duty ignition, not the interrupted sequence stated.
Standard reference: RSOS 2025 E-14.01.03P
Besides flow rating, what two spray characteristics must match the approved oil-nozzle specification when choosing a replacement?
Answer: Spray angle and spray pattern.
Nozzles with the same flow rating can distribute oil differently. Their angle and pattern must match the approved burner and appliance combination for correct flame shape and combustion.
Exam trap: Matching only the flow rating can place the spray incorrectly in the combustion head or chamber.
Standard reference: RSOS 2025 F-15.03.01L
A replacement circulator must remain off when its control relay is de-energized. The relay common receives line power, and neutral goes directly to the motor. Which relay contact should feed the motor’s line lead?
Answer: The normally open contact.
With line on common, the normally open path remains disconnected when the relay is released. Energizing the relay closes that path and supplies the circulator’s line lead.
Exam trap: The normally closed contact would power the circulator in the relay’s de-energized state.
Standard reference: RSOS 2025 F-17.01.02P