Pass Your Red Seal
Exams

Online Red Seal Exam Preparation, built on official standards

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

Mobile Crane Operator

Built on official standards for your trade

Practice exams split like the real exam.
Every answer explained.

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

4
Practice exams
440
Questions
220
Flashcards
1,000+
Flashcard Match
50+
Trade math
100+
Simulations
Try Mobile Crane Operator free12 sample questions now, or Exam 1 with a free account12 sample questionsFree Exam 1

Practice exams

4 exams · 110 questions each

Exam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works

4 practice exams and 440 original practice questions with answers and explanations, plus 220 flashcards in two exam-weighted sets, for the 110-question Mobile Crane Operator Red Seal exam. Timed or untimed, with pause and resume. 110 questions in the real exam · 4 hours · 70% pass mark.

Mobile Crane Operator sample exam questions

Take them as an exam

12 free practice questions with answers and explanations. No account needed.

Sample 1 Mobile Crane Operator, free sample

A cutting-task assessment specifies approved filter eye protection for the identified radiant hazard and an additional face shield for flying particles. Which PPE selection meets both controls?

Answer Wear the specified filter eye protection with the additional face shield
Why The specified filter controls the cutting radiation and the added shield provides the assessed face protection. Clear impact lenses alone do not supply the required radiation filter. Omitting the shield leaves the assessed face exposure uncontrolled; clear lenses without it omit both controls. Select filter shade and compatible PPE for the actual process and conditions. A face shield supplements suitable primary eye protection.
2. For a lift calculation, a glazing panel contains 1800 kg of glass and a 160 kg frame. The vacuum lifter weighs 240 kg. What combined mass do these three components add to the suspended load, before hook-block and other chart deductions?
Answer 2200 kg, accounting for the glass, aluminium frame and vacuum lifter
Why Add all three specified masses: 1800 + 160 + 240 = 2200 kg. The 1960 kg choice omits the lifter; 2040 kg omits the frame; 1800 kg omits both. Each is lifted with the panel. Complete the chart calculation with all other applicable suspended equipment and deductions, avoiding omissions or double counting under the actual crane chart conventions.
3. A bridle leg has an applicable tension rating of 4000 kg-equivalent and is inclined 60° above horizontal. Using sin 60° = 0.866, what vertical load component can that leg support at its rated tension?
Answer 3464 kg-equivalent, multiplying the tension rating by sine of the angle
Why The vertical component is tension × sin 60° = 4000 × 0.866 = 3464 kg-equivalent. Dividing by sine calculates tension from a vertical share instead of the requested component. Using cos 60° gives the horizontal component, and dividing by that cosine reverses another relationship. The sling’s tension rating is not increased by angling it; total bridle capacity also depends on load sharing and the approved assembly.
4. During a lift, one outrigger mat begins sinking and fresh pavement cracks spread around it. The planned radius is unchanged. What does this evidence require?
Answer Suspend the lift and follow the approved response for loss of ground support
Why Sinking and cracking indicate that the support assumption is no longer valid. Stop progression of the lift and follow the site and manufacturer response to stabilize or safely land the load as conditions permit. An unchanged radius does not preserve capacity when support fails. Continuing at either a faster or slower swing rate still loads the deteriorating support. Ground bearing and support must be reassessed before lifting resumes.
5. A round sling has a cover cut exposing its load-bearing core. A separate web sling has melted, hardened fibres. Which inspection disposition follows?
Answer Withdraw the two slings from service and identify them for controlled disposition
Why Exposed round-sling core and melted web fibres are separate removal conditions. Releasing either sling leaves its identified damage in service. An improvised field reduction does not establish a reliable capacity for degraded fibres. Tag and segregate the equipment and follow manufacturer and workplace disposition requirements; do not confuse a protective cover with permission to use an exposed core.
6. An engineered upending plan lists gross crane loads and chart capacities at three critical stages: start 36 t/50 t, mid-rotation 42 t/48 t, and final suspension 68 t/80 t. Which stage has the highest capacity utilization?
Answer Mid-rotation at 87.5%, using its stage-specific load and capacity
Why Utilization is load divided by capacity at the same stage. Start is 36/50 = 72%; mid-rotation is 42/48 = 87.5%; final suspension is 68/80 = 85%. Thus the middle stage governs this comparison despite the final load being heavier. The 136% result mixes two different stages. Upending load share and crane capacity must be checked throughout the engineered path; neither a universal starting maximum nor a fixed half-load assumption is valid.
7. The approved lift uses a 32 t counterweight configuration. A 40 t configuration is also available, with a different chart and limiter code. Which setup implements the approved lift?
Answer Install 32 t and select the matching 32 t configuration code
Why The actual counterweight, selected code and approved chart must agree. A 32 t stack with the 40 t code misrepresents the machine to the limiter. A 40 t stack with its matching code still changes the approved configuration and requires reassessment. A 40 t stack with the 32 t code introduces both a plan deviation and configuration mismatch; extra counterweight is not blanket permission to proceed.
8. A crane-specific dismantling instruction requires a jib assembly to be independently supported and pendant tension released before its connecting pins are withdrawn. The supports are in position, but a pendant remains tensioned. What must happen before pin withdrawal?
Answer Verify the support load path and release pendant tension by the prescribed method
Why Positioned stands do not prove they carry the assembly, and a tensioned pendant indicates a remaining force to control. Establish the prescribed support load path and release the specified tension before pin removal. Checking stand position alone, pendant appearance alone, or pin markings does not satisfy those prerequisites. Dismantling sequence and load transfer must come from the actual crane instructions; simply reversing assembly is not a universal safe procedure.
9. A counterweight-removal procedure gives support and level checks at each transfer stage. During transfer, a support reaction changes and the crane moves outside the procedure’s level limit. What is the appropriate response?
Answer Stop the transfer and restore the specified support condition by the approved procedure
Why A level-limit exceedance invalidates the specified setup condition, so halt progression and apply the approved support response. Waiting until the last slab leaves the deviation uncontrolled. Suppressing or relying on an earlier indication does not restore level. Slab count cannot substitute for the required measurement. Support redistribution depends on actual geometry; adjusting outriggers under load without the prescribed procedure is not an assumed remedy.
10. A friction-hoist inspection finds that the load brake creeps during the prescribed holding test. The clutch and swing brake pass their separate tests. What does this result require before lifting resumes?
Answer Repair the hoist brake and verify it passes the specified load-holding test
Why The hoist brake failed its assigned holding function and requires correction and verification. A passing clutch does not establish that the defective brake can hold the load. The swing brake controls a different motion and cannot substitute for hoist holding. Passing unrelated tests does not cancel the failed result. Follow the specific friction-hoist operating and maintenance procedure rather than assuming a universal clutch/brake lowering sequence.
11. A suspended-ballast lift configuration requires a specified tray radius and clearance throughout the planned move. Before travel, the tray contacts the ground although the radius indication matches the plan. What should the operator do?
Answer Stop the move and resolve the clearance deviation under the approved lift procedure
Why Radius and clearance are separate requirements in this specified suspended-ballast configuration. A matching radius does not make ground contact acceptable. Changing radius or mass changes the engineered configuration and cannot be improvised to clear the tray. Stop and have the deviation resolved under the approved procedure. Other ballast systems can have different support arrangements; this item does not assert that every superlift tray must always be airborne.
12. At the working radius, a chart lists 18 t at 30 m boom length and 16 t at 34 m. Its note requires the lower bracketing capacity at intermediate lengths. At 32 m, which chart capacity applies before other deductions?
Answer 16 t, taking the lower of the two bracketing capacities
Why The chart note explicitly selects the lower bracketing value, so 16 t applies. Choosing 18 t uses the higher value; 17 t interpolates when the note does not permit it. Adding values from two alternative configurations has no capacity meaning. Apply the actual chart notes, configuration and deductions; a generic longer-boom assumption does not replace the stated rule.

Start free

Interactive simulations

Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.

Diagrams and symbols

Learn to read the diagrams and schematic symbols used in your trade.

How things work

Animated section drawings show what happens inside the equipment as it runs.

Terminology

Learn the correct name and job of every part.

Exam breakdown

Red Seal practice tests and exam prep

The official Mobile Crane Operator Red Seal exam, also called the interprovincial (IP) exam, has 110 questions across 7 topic blocks. Open a block to see its tasks and subtasks.

110
Multiple choice questions
4 hours
Writing time
70%
Pass mark
Major Work Activity% of examReal examPractice bank
APerforms common occupational skills5%728

A-1 · Performs safety-related functions

4 official exam questions · 20 in the practice bank

  • A-1.01 Maintains safe work environment
  • A-1.02 Uses personal protective equipment (PPE) and safety equipment
  • A-1.03 Uses documentation

A-2 · Uses communication and mentoring techniques

3 official exam questions · 8 in the practice bank

  • A-2.01 Uses communication techniques
  • A-2.02 Uses mentoring techniques
BPerforms hoisting calculations18%2080

B-3 · Determines load weights

6 official exam questions · 24 in the practice bank

  • B-3.01 Identifies weight
  • B-3.02 Calculates weight

B-4 · Calculates crane capacity

8 official exam questions · 32 in the practice bank

  • B-4.01 Determines radius and crane configuration
  • B-4.02 Interprets load charts

B-5 · Performs rigging calculations

6 official exam questions · 24 in the practice bank

  • B-5.01 Performs sling angle calculations
  • B-5.02 Performs working load limit (WLL) calculations
CInspects and maintains crane13%1456

C-6 · Performs pre-operational checks and regular inspections

6 official exam questions · 32 in the practice bank

  • C-6.01 Inspects engine systems
  • C-6.02 Inspects air systems
  • C-6.03 Inspects electrical systems
  • C-6.04 Inspects hydraulic systems
  • C-6.05 Inspects chassiscar body and running gear components
  • C-6.06 Inspects outriggers and counterweights
  • C-6.07 Inspects boom components and attachments
  • C-6.08 Inspects hoisting systems

C-7 · Performs operational and continual checks

5 official exam questions · 15 in the practice bank

  • C-7.01 Checks operating controls
  • C-7.02 Inspects monitoring and warning systems
  • C-7.03 Monitors running lines, hoist ropes and standing ropes
  • C-7.04 Monitors gauges and warning systems
  • C-7.05 Monitors support base

C-8 · Performs minor crane maintenance

3 official exam questions · 9 in the practice bank

  • C-8.01 Changes oil and filter
  • C-8.02 Greases crane
  • C-8.03 Lubricates wire ropes
  • C-8.04 Makes adjustments and replacements
DPerforms rigging12%1352

D-9 · Inspects, maintains and stores slings and hardware

6 official exam questions · 28 in the practice bank

  • D-9.01 Lubricates slings and hardware
  • D-9.02 Identifies deficiencies in slings and hardware
  • D-9.03 Disposes of damaged slings and hardware
  • D-9.04 Stores slings and hardware

D-10 · Follows rigging procedures

7 official exam questions · 24 in the practice bank

  • D-10.01 Selects required rigging
  • D-10.02 Rigs loads
  • D-10.03 Monitors rigging
EPlans lift, prepares site and sets up crane15%1664

E-11 · Performs pre-lift planning

9 official exam questions · 28 in the practice bank

  • E-11.01 Participates in routine, engineered and specialty lift planning
  • E-11.02 Evaluates risks and hazards

E-12 · Sets up crane

7 official exam questions · 36 in the practice bank

  • E-12.01 Performs final site inspection
  • E-12.02 Positions crane
  • E-12.03 Completes setup
FAssembles, disassembles and transports crane14%1560

F-13 · Loads and unloads components for transport

3 official exam questions · 2 in the practice bank

  • F-13.01 Loads crane and components
  • F-13.02 Unloads crane and components

F-14 · Drives crane on public roadways

2 official exam questions · 3 in the practice bank

  • F-14.01 Performs pre-trip planning
  • F-14.02 Prepares crane for transport
  • F-14.03 Drives cranes

F-15 · Assembles and disassembles lattice boom cranes

4 official exam questions · 28 in the practice bank

  • F-15.01 Installs tracks on car body (lattice boom)
  • F-15.02 Installs superstructureupperworks (lattice boom)
  • F-15.03 Installs outrigger boxes (lattice boom)
  • F-15.04 Installs boom base (lattice boom)
  • F-15.05 Installs counterweights (lattice boom)
  • F-15.06 Assembles main boom, tip and boom attachments (lattice boom)
  • F-15.07 Installs hook blocks and overhaul ball (lattice boom)
  • F-15.08 Removes hook blocks and overhaul ball (lattice boom)
  • F-15.09 Disassembles main boom, tip and boom attachments (lattice boom)
  • F-15.10 Removes counterweights (lattice boom)
  • F-15.11 Removes boom base (lattice boom)
  • F-15.12 Removes superstructureupperworks (lattice boom)
  • F-15.13 Removes tracks from car body (lattice boom)
  • F-15.14 Removes outrigger boxes (lattice boom)

F-16 · Assembles and disassembles telescopic boom cranes

4 official exam questions · 25 in the practice bank

  • F-16.01 Installs tracks on car body (telescopic boom)
  • F-16.02 Installs outrigger boxes (telescopic boom)
  • F-16.03 Installs superstructureupperworks (telescopic boom)
  • F-16.04 Installs main boom (telescopic boom)
  • F-16.05 Installs hook blocks and overhaul ball (telescopic boom)
  • F-16.06 Installs counterweights (telescopic boom)
  • F-16.07 Installs jibs and inserts (telescopic boom)
  • F-16.08 Removes jibs and inserts (telescopic boom)
  • F-16.09 Removes counterweights (telescopic boom)
  • F-16.10 Removes hook blocks and overhaul ball (telescopic boom)
  • F-16.11 Removes main boom (telescopic boom)
  • F-16.12 Removes outrigger boxes (telescopic boom)
  • F-16.13 Removes tracks from car body (telescopic boom)
  • F-16.14 Removes superstructureupperworks (telescopic boom)

F-17 · Assembles and disassembles specialty equipment and attachments

2 official exam questions · 2 in the practice bank

  • F-17.01 Assembles specialty equipment and attachments
  • F-17.02 Disassembles specialty equipment and attachments
GOperates crane23%25100

G-18 · Performs common craning operations

5 official exam questions · 16 in the practice bank

  • G-18.01 Configures load moment indicator (LMI)
  • G-18.02 Mobilizes crane on jobsite

G-19 · Operates friction drive lattice boom cranes

2 official exam questions · 8 in the practice bank

  • G-19.01 Operates friction drive crawler-mounted lattice boom cranes
  • G-19.02 Operates friction drive truck-mounted lattice boom cranes

G-20 · Operates hydraulic drive lattice boom cranes

6 official exam questions · 18 in the practice bank

  • G-20.01 Operates hydraulic drive crawler-mounted lattice boom cranes
  • G-20.02 Operates hydraulic drive truck-mounted lattice boom cranes

G-21 · Operates telescopic boom cranes

5 official exam questions · 16 in the practice bank

  • G-21.01 Operates crawler-mounted telescopic cranes
  • G-21.02 Operates rubber tire-mounted telescopic cranes

G-22 · Performs specialty craning operations

4 official exam questions · 32 in the practice bank

  • G-22.01 Operates crane with piledriving equipment
  • G-22.02 Performs duty cycle operations
  • G-22.03 Operates cranes on floating platforms
  • G-22.04 Performs multi-crane lifts
  • G-22.05 Uses personnel hoisting equipment

G-23 · Secures crane

3 official exam questions · 10 in the practice bank

  • G-23.01 Secures crane for short term
  • G-23.02 Secures crane for long term

Source: the official Mobile Crane Operator standard and exam breakdown. Check your own requirements with your province or territory.

Questions about Mobile Crane Operator exam prep

Study guide
Is there a free Mobile Crane Operator Red Seal practice test?

Yes. Mobile Crane Operator Exam 1 is a full practice exam of 110 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.

Is there a Mobile Crane Operator practice test with answers?

Yes. Every Mobile Crane Operator practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.

How many questions are on the Mobile Crane Operator Red Seal exam?

The official Mobile Crane Operator Red Seal exam has 110 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 77 of 110 questions correct.

What topics are on the Mobile Crane Operator Red Seal exam?

The published exam breakdown has 7 Major Work Activities (MWAs) or blocks: A, Performs common occupational skills (7 questions); B, Performs hoisting calculations (20 questions); C, Inspects and maintains crane (14 questions); D, Performs rigging (13 questions); E, Plans lift, prepares site and sets up crane (16 questions); F, Assembles, disassembles and transports crane (15 questions); G, Operates crane (25 questions).

Can I challenge the Mobile Crane Operator Red Seal exam without an apprenticeship?

Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 110-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 5,400 in British Columbia to 8,100 in Prince Edward Island (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.

How do your Mobile Crane Operator practice exams follow the official breakdown?

Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.

What are Flashcard Match and Question Match?

Flashcard Match deals a board of Mobile Crane Operator flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Mobile Crane Operator practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.

How many Mobile Crane Operator practice exams are included?

Pass Your Red Seal includes 4 practice exams and 440 original practice questions for Mobile Crane Operator. Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 110 questions on the official exam.

Are Mobile Crane Operator flashcards included?

Yes. Every Mobile Crane Operator plan includes 220 flashcards in two exam-weighted sets of 110 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard - Mobile Crane Operator (2021) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.

Can I try Mobile Crane Operator practice questions for free?

Yes. Try 12 free Mobile Crane Operator questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.

How much does Mobile Crane Operator study access cost?

Study access for Mobile Crane Operator costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.

Challenge the Mobile Crane Operator exam without an apprenticeship

How it works

Experienced workers in the mobile crane operator trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.

Experience required to challenge the Mobile Crane Operator Red Seal exam
Province or territory, with its guideHours to challengeApprenticeship and certification
British Columbia5,400Apprenticeship 5,400 hours · voluntary certification
Alberta
Crane and Hoisting Equipment Operator - Mobile Crane
7,560Apprenticeship 5,400 hours · compulsory certification
Saskatchewan8,100Apprenticeship 5,400 hours · voluntary certification
Manitoba8,100Apprenticeship 5,400 hours · compulsory certification
Ontario
Hoisting Engineer - Mobile Crane Operator 1
6,000Apprenticeship 6,000 hours · compulsory certification
Quebec
Crane Operator
Quebec certificate firstApprenticeship 4,000 hours · compulsory certification
New Brunswick8,100Apprenticeship 5,400 hours · compulsory certification
Nova ScotiaA certificate, not hoursVoluntary certification · Nova Scotia asks for a Mobile Crane Operator 1 or 2 certificate; another body regulates the trade
Prince Edward Island8,100Apprenticeship 5,400 hours · voluntary certification
Newfoundland and LabradorNo challenge routeApprenticeship 5,400 hours · compulsory certification
YukonNot shown
Northwest Territories7,200Apprenticeship 5,400 hours · voluntary certification
Nunavut
Crane and Hoisting Equipment Operator - Mobile Crane
7,200Apprenticeship 5,400 hours · voluntary certification

Source: Ellis Chart, Mobile Crane Operator, published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.