Pass Your Red Seal
Exams

Online Red Seal Exam Preparation, built on official standards

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

Tool and Die Maker

Built on official standards for your trade

Practice exams split like the real exam.
Every answer explained.

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

4
Practice exams
540
Questions
270
Flashcards
1,000+
Flashcard Match
50+
Trade math
100+
Simulations
Try Tool and Die Maker free12 sample questions now, or Exam 1 with a free account12 sample questionsFree Exam 1

Practice exams

4 exams · 135 questions each

Exam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works

4 practice exams and 540 original practice questions with answers and explanations, plus 270 flashcards in two exam-weighted sets, for the 135-question Tool and Die Maker Red Seal exam. Timed or untimed, with pause and resume. 135 questions in the real exam · 4 hours · 70% pass mark.

Tool and Die Maker sample exam questions

Take them as an exam

12 free practice questions with answers and explanations. No account needed.

Sample 1 Tool and Die Maker, free sample

A hardened punch-holder process plan requires rough machining while soft, heat treatment with finishing stock retained, then final datum grinding before jig grinding locating holes from that datum. Which sequence follows?

Answer Rough machine, heat treat, grind the datum, then jig grind the locating holes
Why The prescribed sequence allows final geometry to be established after heat-treatment movement, with the finished datum available for hole location. Finishing holes before heat treatment risks later dimensional change. Finishing both datum and holes beforehand leaves both exposed. Finishing holes before the final datum reverses the stated referencing sequence. Alternative processes require their own validated plan; this item does not claim all hardened features must always be made by one method.
2. A hole has size limits 25.000–25.050 mm and a diametrical position tolerance of 0.050 mm at MMC. Its applicable actual mating size is 25.040 mm. With no datum-shift allowance, what total diametrical position tolerance is available?
Answer 0.090 mm, adding the 0.040 mm size departure to the stated tolerance
Why For this internal feature, MMC is its smallest permitted size, 25.000 mm. The applicable departure is 25.040 − 25.000 = 0.040 mm, giving 0.050 + 0.040 = 0.090 mm. Subtracting reverses the bonus; 0.050 omits it; 0.040 omits the original position tolerance. Size conformance remains a separate requirement, and no datum mobility has been added.
3. A blade supplier’s setup sheet for the selected stock and blade specifies 25–30 m/min, a 4–6 TPI variable pitch and flood coolant. Which initial setup meets all three values?
Answer 28 m/min with a 4–6 TPI blade and the specified flood coolant
Why Twenty-eight lies within the specified speed range and 4–6 TPI matches the blade selection. The other 28 m/min choice changes pitch. The 60 m/min choices exceed the stated speed range; one also changes pitch. Verify tooth engagement, break-in and feed under the actual supplier guidance. Neither a universal D2 cutting speed nor a general work-hardening claim replaces that setup information.
4. A reaming process specifies an 8.000 mm finished hole and a pre-ream diameter that leaves 0.200 mm diametral stock. Assuming the drilled hole achieves its nominal diameter, what pre-ream size is required?
Answer 7.800 mm, deducting all of the diametral stock from the finished hole size
Why Subtract the stated diametral stock: 8.000 − 0.200 = 7.800 mm. The 7.900 mm choice treats the diametral allowance as if it needed halving. The larger-than-finish choices add rather than leave removable stock. Confirm the actual pre-hole and tool recommendations; reaming follows the prepared hole and is not a general method of relocating an incorrectly positioned hole.
5. A dividing head has a 40:1 ratio. Six equally spaced holes are required, and an 18-hole index circle is available. What crank movement gives each division? Count intervals between holes, excluding the starting hole.
Answer Six full turns plus twelve intervals on the eighteen-hole indexing ring
Why Crank turns per division are 40/6 = 6⅔. Two-thirds of 18 intervals is 12, so use six full turns plus twelve intervals. Six intervals uses one-third instead. Thirteen and seven are off-by-one versions of those counts when the starting hole is incorrectly included. Use the prescribed indexing direction and backlash control; each complete crank turn rotates the spindle 1/40 revolution.
6. A new 200 mm vitrified grinding wheel is of a type requiring a ring test before mounting. The grinder is isolated for installation. Which sequence satisfies that inspection and guarded start-up requirement?
Answer Inspect and ring-test before mounting, then perform the prescribed guarded test run
Why Inspect and perform the applicable ring test before mounting; reject a suspect wheel. After correct mounting and setup, replace the guard and follow the prescribed test run with people clear of the wheel’s plane. Running before the required inspection exposes personnel to an unchecked wheel. Either unguarded choice omits a required safeguard. Ring testing is not appropriate to every wheel type, and no test makes visible damage acceptable.
7. The program X–Y datum is the centre of a locating bore. A calibrated spindle probe and an approved internal-circle routine are available. Which measurement establishes that datum from the specified feature?
Answer Probe the bore at the routine’s multiple contacts and calculate its X–Y centre
Why The internal-circle routine uses the calibrated probe contacts to determine the bore centre. One wall contact alone lacks the geometry needed for an unknown centre. A depth touch gives Z information, not X–Y location. Outside edges are different features and cannot be assumed to coincide with the required bore centre. Apply the routine’s clearance, calibration and offset-writing checks; a fitted centre is a measured estimate, not error-free truth.
8. A deep sinker-EDM cavity develops unstable discharges. The validated setup requires through-electrode flushing and periodic jump cycles. A flow check passes, but the recorded jump cycle is disabled. Which controlled change should be evaluated first?
Answer Restore the specified jump cycle and evaluate discharge stability and wall condition
Why The recorded setup deviates at the jump cycle, which periodically opens the gap to help exchange contaminated dielectric. Restore that validated setting and assess the result. Changing energy in either direction leaves the identified omission. Disabling a passing flushing supply removes another required control. Pressure and suction flushing can each suit different geometries; suction is not universally inferior for a deep cavity.
9. A steel heat-treatment instruction calls for austenitizing followed by cooling in still air to refine the structure before finish machining. Which process name matches that cycle?
Answer Normalizing, using austenitizing followed by the specified air cooling
Why Austenitizing followed by the stated still-air cooling describes normalizing. Full annealing uses a different cooling cycle. Subcritical stress relief does not austenitize the steel. Spheroidizing aims to change carbide morphology through its specified cycle and is not the cycle described. Select actual temperatures and cooling conditions for the steel and section; normalizing does not guarantee elimination of chemical segregation or all banding.
10. A locating-hole measurement is 8.000 mm. The approved assembly requires 0.005–0.010 mm diametral interference. Which measured pin diameter meets that range?
Answer 8.008 mm, giving a pin-to-hole interference of eight micrometres
Why Interference is pin diameter minus hole diameter: 8.008 − 8.000 = 0.008 mm, within the specified interval. The 8.003 mm pin gives only 0.003 mm interference. Both smaller pins provide clearance rather than interference. Nominal labels alone do not establish actual fit; use measured sizes, specified tolerances and the approved assembly procedure.
11. A single-row strip layout uses 30.0 mm diameter blanks. Its approved layout requires a 1.5 mm scrap bridge between consecutive blank edges. What centre-to-centre feed pitch follows?
Answer 31.5 mm, adding one specified bridge to the blank diameter
Why Consecutive centres are separated by one blank diameter plus the bridge: 30.0 + 1.5 = 31.5 mm. Adding two bridges double-counts the gap. Either subtraction makes the pitch shorter than the blank diameter and creates overlap. Edge margins, strip strength and carrier design require their own approved dimensions; a bridge equal to material thickness is not a universal rule.
12. A punch has a 0.30 mm-deep edge chip. Its approved repair permits grinding 0.35 mm from the cutting face and provides enough remaining length for the specified reset. Which repair and verification follow?
Answer Grind the permitted face amount, inspect the restored edge and reset working length
Why The authorized removal exceeds the chip depth and can restore a continuous edge, which must be inspected before resetting and checking the working length. Omitting the length check ignores material removed from the face. Stoning corners leaves the missing edge; changing hardness does not replace missing material. Confirm damage extent, remaining geometry and the repair allowance rather than assuming every chipped punch can be ground and shimmed.

Start free

Interactive simulations

Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.

Diagrams and symbols

Learn to read the diagrams and schematic symbols used in your trade.

How things work

Animated section drawings show what happens inside the equipment as it runs.

Terminology

Learn the correct name and job of every part.

Exam breakdown

Red Seal practice tests and exam prep

The official Tool and Die Maker Red Seal exam, also called the interprovincial (IP) exam, has 135 questions across 4 topic blocks. Open a block to see its tasks and subtasks.

135
Multiple choice questions
4 hours
Writing time
70%
Pass mark
Major Work Activity% of examReal examPractice bank
APerforms common occupational skills15%2080

A-1 · Performs safety-related functions

5 official exam questions · 24 in the practice bank

  • A-1.01 Maintains safe work environment
  • A-1.02 Uses personal protective equipment (PPE) and safety equipment
  • A-1.03 Uses hoisting, lifting, rigging and supporting equipment

A-2 · Maintains machine-tools, accessories and cutting tools

3 official exam questions · 10 in the practice bank

  • A-2.01 Maintains machine-tools and accessories
  • A-2.02 Maintains cutting tools

A-3 · Organizes work

5 official exam questions · 16 in the practice bank

  • A-3.01 Interprets drawings, specifications and applications
  • A-3.02 Plans project activities

A-4 · Performs benchwork

5 official exam questions · 22 in the practice bank

  • A-4.01 Performs layout
  • A-4.02 Finishes workpiece
  • A-4.03 Inspects workpiece

A-5 · Uses communication and mentoring techniques

2 official exam questions · 8 in the practice bank

  • A-5.01 Uses communication techniques
  • A-5.02 Uses mentoring techniques
BOperates machine-tools33%45180

B-6 · Operates power saws

4 official exam questions · 15 in the practice bank

  • B-6.01 Sets up power saws
  • B-6.02 Saws straight and angle cuts
  • B-6.03 Cuts irregular shapes

B-7 · Operates drill presses

4 official exam questions · 23 in the practice bank

  • B-7.01 Sets up drill presses
  • B-7.02 Drills holes using drill presses
  • B-7.03 Cuts countersinks, counterbores, chamfers and spot faces using drill presses
  • B-7.04 Performs tapping using drill presses
  • B-7.05 Finishes holes using drill presses

B-8 · Operates conventional lathes

9 official exam questions · 32 in the practice bank

  • B-8.01 Sets up conventional lathes
  • B-8.02 Faces surface using conventional lathes
  • B-8.03 Turns internal and external surfaces using conventional lathes
  • B-8.04 Creates holes using conventional lathes

B-9 · Operates conventional milling machines

9 official exam questions · 24 in the practice bank

  • B-9.01 Sets up conventional milling machines
  • B-9.02 Mills surfaces using conventional milling machines
  • B-9.03 Creates holes and hole features using conventional milling machines

B-10 · Operates grinding machines

9 official exam questions · 48 in the practice bank

  • B-10.01 Sets up grinding machines
  • B-10.02 Grinds flat surfaces using a surface grinder
  • B-10.03 Grinds profiles
  • B-10.04 Grinds internal and external cylindrical and tapered surfaces
  • B-10.05 Grinds tools and cutters
  • B-10.06 Finishes holes using a honing machine

B-11 · Operates computer numerical control (CNC) machines

6 official exam questions · 30 in the practice bank

  • B-11.01 Performs CNC programming
  • B-11.02 Inputs program data into control memory
  • B-11.03 Establishes workpiece datum
  • B-11.04 Verifies programs
  • B-11.05 Monitors machining processes

B-12 · Operates electrical discharge machines (EDM)

4 official exam questions · 8 in the practice bank

  • B-12.01 Determines flushing methods
  • B-12.02 Sets cutting conditions
CPerforms heat treatment10%1352

C-13 · Heat treats materials

10 official exam questions · 46 in the practice bank

  • C-13.01 Selects heat treatment process
  • C-13.02 Hardens materials
  • C-13.03 Tempers materials
  • C-13.04 Anneals materials
  • C-13.05 Normalizes materials
  • C-13.06 Case hardens materials

C-14 · Tests heat treated materials

3 official exam questions · 6 in the practice bank

  • C-14.01 Performs visual inspection
  • C-14.02 Performs hardness test
DPerforms design and development of prototypes and production tools42%57228

D-15 · Performs production tool design

9 official exam questions · 32 in the practice bank

  • D-15.01 Identifies production tool requirements
  • D-15.02 Prepares shop sketches
  • D-15.03 Determines production tool material specifications and engineered components
  • D-15.04 Prepares information for designing and drafting

D-16 · Develops prototype

6 official exam questions · 30 in the practice bank

  • D-16.01 Selects prototyping technique and materials
  • D-16.02 Fabricates prototype components
  • D-16.03 Assembles prototype components
  • D-16.04 Inspects prototype
  • D-16.05 Proves out prototype

D-17 · Fits and assembles production tools

15 official exam questions · 36 in the practice bank

  • D-17.01 Verifies dimensions of production tool components
  • D-17.02 Performs production tool assembly
  • D-17.03 Sets production tool timing

D-18 · Proves out production tools

14 official exam questions · 88 in the practice bank

  • D-18.01 Sets up production tools
  • D-18.02 Verifies production part material
  • D-18.03 Develops blank/strip
  • D-18.04 Cycles equipment with production tools
  • D-18.05 Evaluates production part
  • D-18.06 Checks production tool for damage
  • D-18.07 Modifies production tools to enhance productivity

D-19 · Repairs and maintains production tools

13 official exam questions · 42 in the practice bank

  • D-19.01 Identifies condition of production tools
  • D-19.02 Identifies repair procedures
  • D-19.03 Adjusts production tool components
  • D-19.04 Reconditions production tool components

Source: the official Tool and Die Maker standard and exam breakdown. Check your own requirements with your province or territory.

Questions about Tool and Die Maker exam prep

Study guide
Is there a free Tool and Die Maker Red Seal practice test?

Yes. Tool and Die Maker Exam 1 is a full practice exam of 135 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.

Is there a Tool and Die Maker practice test with answers?

Yes. Every Tool and Die Maker practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.

How many questions are on the Tool and Die Maker Red Seal exam?

The official Tool and Die Maker Red Seal exam has 135 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 95 of 135 questions correct.

What topics are on the Tool and Die Maker Red Seal exam?

The published exam breakdown has 4 Major Work Activities (MWAs) or blocks: A, Performs common occupational skills (20 questions); B, Operates machine-tools (45 questions); C, Performs heat treatment (13 questions); D, Performs design and development of prototypes and production tools (57 questions).

Can I challenge the Tool and Die Maker Red Seal exam without an apprenticeship?

Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 135-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 2,700 in British Columbia to 10,800 in Newfoundland and Labrador (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.

How do your Tool and Die Maker practice exams follow the official breakdown?

Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.

What are Flashcard Match and Question Match?

Flashcard Match deals a board of Tool and Die Maker flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Tool and Die Maker practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.

How many Tool and Die Maker practice exams are included?

Pass Your Red Seal includes 4 practice exams and 540 original practice questions for Tool and Die Maker. Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 135 questions on the official exam.

Are Tool and Die Maker flashcards included?

Yes. Every Tool and Die Maker plan includes 270 flashcards in two exam-weighted sets of 135 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard - Tool and Die Maker (2019) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.

Can I try Tool and Die Maker practice questions for free?

Yes. Try 12 free Tool and Die Maker questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.

How much does Tool and Die Maker study access cost?

Study access for Tool and Die Maker costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.

Challenge the Tool and Die Maker exam without an apprenticeship

How it works

Experienced workers in the tool and die maker trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.

Experience required to challenge the Tool and Die Maker Red Seal exam
Province or territory, with its guideHours to challengeApprenticeship and certification
British Columbia2,700Voluntary certification
AlbertaNo challenge route
SaskatchewanNo challenge route
Manitoba10,800Apprenticeship 7,200 hours · voluntary certification
Ontario8,000Apprenticeship 8,000 hours · voluntary certification
Quebec
Tool and Die Maker; Machinist/Mould maker; Die maker; Tool Maker
Quebec certificate firstApprenticeship Not specified hours · voluntary certification
New Brunswick7,200Voluntary certification
Nova Scotia10,800Voluntary certification
Prince Edward Island10,000Voluntary certification
Newfoundland and Labrador10,800Voluntary certification
YukonNot shown
Northwest TerritoriesNo challenge route
NunavutNo challenge route

Source: Ellis Chart, Tool and Die Maker, published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.