Pass Your Red Seal
Exams

Online Red Seal Exam Preparation, built on official standards

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

Metal Fabricator (Fitter)

Built on official standards for your trade

Practice exams split like the real exam.
Every answer explained.

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

3
Practice exams
390
Questions
260
Flashcards
1,000+
Flashcard Match
50+
Trade math
100+
Simulations
Try Metal Fabricator (Fitter) free12 sample questions now, or Exam 1 with a free account12 sample questionsFree Exam 1

Practice exams

3 exams · 130 questions each

Exam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works

3 practice exams and 390 original practice questions with answers and explanations, plus 260 flashcards in two exam-weighted sets, for the 130-question Metal Fabricator (Fitter) Red Seal exam. Timed or untimed, with pause and resume. 130 questions in the real exam · 4 hours · 70% pass mark.

Metal Fabricator (Fitter) sample exam questions

Take them as an exam

12 free practice questions with answers and explanations. No account needed.

Sample 1 Metal Fabricator (Fitter), free sample

A moveable welding-fume hood has a 150 mm duct. Before airflow is checked and the hood is adjusted for the weld, approximately how far from the arc is its recommended initial position?

Answer About one hundred fifty millimetres.
Why For an initial setup, CCOHS recommends a hood distance of about one duct diameter: 150 mm here. The 300 mm and 450 mm choices place it two and three diameters away, reducing capture effectiveness. The 75 mm choice is only half a diameter and can place excessive suction close to the shielding zone. The initial position must still be checked for capture and shielding performance.
2. A bench-grinder inspection records a 4 mm work-rest gap and a 5 mm tongue-guard gap. Using the CCOHS maximum-clearance guidance, which finding identifies the setting outside its limit?
Answer The work-rest clearance exceeds its limit; the tongue gap is within it.
Why CCOHS gives a maximum 3 mm work-rest gap and 6 mm tongue-guard gap. Thus 4 mm exceeds the work-rest limit, while 5 mm remains within the tongue limit. Reversing the two limits incorrectly identifies only the tongue gap as outside its limit. Applying 3 mm to both components incorrectly classifies both gaps as excessive; applying 6 mm to both incorrectly classifies both as within their limits. Adjust only with the wheel stopped, following the machine instructions.
3. On a standard welding symbol, a fillet-weld triangle appears below the single solid reference line. Which joint location does it specify?
Answer A fillet weld along the joint's arrow-side face.
Why A weld symbol below the reference line specifies the arrow side; above specifies the other side. Both-side welding requires symbols on both sides of the line. Either-side selection is not conveyed by putting one fillet symbol below the line. The arrow may attach to either end without changing this convention.
4. An inspection drawing uses ISO 2553 notation and specifies a fillet weld as a6. Which dimension is to be checked against the 6 mm requirement?
Answer The design throat of the fillet weld.
Why In the ISO convention, a identifies design throat, so a6 specifies a 6 mm design throat. z identifies leg length, while s identifies penetration throat. Face width is not what the a prefix designates. The symbols must be read in the convention the drawing specifies, not in another system’s size notation.
5. For preliminary lift planning, approximately what mass should be assigned to an unperforated carbon-steel plate measuring 2 m by 1 m by 10 mm, before lifting attachments are added?
Answer Approximately one hundred fifty-seven kilograms.
Why Carbon steel is commonly estimated at 7850 kg/m³. Convert 10 mm to 0.010 m: the volume is 2 × 1 × 0.010 = 0.020 m³, giving 157 kg. The 78.5 kg choice halves the correct plate volume. The 1570 kg and 15.7 kg choices each place the thickness decimal one position incorrectly. Add actual attachments and lifting gear separately and verify the load before the lift.
6. A welding handover instructs the crew to backgouge the joint before welding its second side. Which description communicates that operation?
Answer Remove reverse-side root metal to expose the first-side weld.
Why Backgouging excavates the reverse side of a two-sided joint to expose sound first-side weld at the root, permitting fusion when the second side is welded. Merely restoring the original opening can leave an unfused or defective root. Removing the crown flush addresses reinforcement, and removing only toe regions addresses surface-edge conditions; neither establishes the sound root required for the reverse weld. The approved procedure determines whether and how backgouging is performed.
7. Which caliper is used to scribe a layout line at a set distance from a finished plate edge?
Answer Firm-joint hermaphrodite calipers.
Why Hermaphrodite, or odd-leg, calipers combine an edge-contacting leg with a scribing point, allowing a set distance to be carried along an edge. Dividers have two points and normally step distances or swing arcs from a point. Inside and outside measuring calipers transfer opposing-surface dimensions; their normal leg arrangement is not the edge-and-scriber arrangement selected for this layout.
8. A deep drilled steel hole has an uneven bore, intermittent cutting sound and irregular feed force. The emerging chips are long and bent rather than curled. Which condition best matches these observations?
Answer Chips are jamming intermittently in the flutes and disturbing drill motion.
Why Sandvik identifies interrupted cutting sound, irregular feed force, long bent chips and an uneven bore together as evidence of chip jamming. Built-up edge is adhered work material on the cutting edge and is promoted by low cutting speed; it can affect finish but does not as directly explain the combined chip-evacuation signature. Run-out gives a repeating off-axis geometry, while uniform flank wear is a progressive cutting-edge condition; neither is the closest match to intermittent force with jammed-looking chips.
9. Standard roll segments on a Baileigh R-M55 are set up for edgewise flat-bar rolling. What upper-roll groove width is specified relative to the material thickness?
Answer Set it 2–4 mm wider than the material thickness.
Why The R-M55 manual calls for the upper-roll groove to be 2–4 mm larger than the material thickness. The 0.2–0.4 mm range shifts the stated allowance by a factor of ten. A narrower groove imposes interference, and an exactly equal width omits the specified clearance. This is that machine's standard-roll setup instruction, rather than a universal clearance for every section roller.
10. An assembly procedure uses the nut-factor method for M20 fasteners. Tests on the specified bolt, nut and lubricant combination establish K = 0.18. What estimated tightening torque corresponds to a target clamp load of 250 kN?
Answer Approximately 900 N·m.
Why The nut-factor relation is T = KdF. Use the nominal diameter 0.020 m and clamp load 250000 N: T = 0.18 × 0.020 × 250000 = 900 N·m. Omitting K gives 5000 N·m; dividing by K gives about 28000 N·m. Using 20 mm as though it were 20 m gives 900000 N·m. This empirical relation estimates torque using the measured K for the specified combination; it does not establish an exact universal torque for every M20 fastener.
11. Which description identifies a bridge tack in a prepared groove joint?
Answer A temporary bead spanning the bevels without fusion into the root.
Why A bridge tack spans between the bevels above the root without penetrating it. A root tack fuses at the root and may be incorporated as the procedure permits. Backing-strip and runoff-tab attachment tacks secure auxiliary pieces and are not bridge tacks spanning the groove. Bridge tacks can be removed when no longer needed, according to the fabrication method.
12. A duplex finish specifies sweep blasting the galvanized surface before powder coating. Which angle and abrasive combination is appropriate?
Answer A 45° nozzle angle using aluminum/magnesium silicate.
Why Sweep blasting zinc uses an oblique angle, typically 30–60°, with a suitable non-iron abrasive such as aluminum/magnesium silicate. Normal incidence is the standard-blast arrangement and can remove excessive zinc. Iron-bearing media can contaminate the galvanized coating and cause powder-adhesion problems. The finish procedure also controls abrasive size, pressure and the coating interval.

Start free

Interactive simulations

Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.

Diagrams and symbols

Learn to read the diagrams and schematic symbols used in your trade.

How things work

Animated section drawings show what happens inside the equipment as it runs.

Terminology

Learn the correct name and job of every part.

Exam breakdown

Red Seal practice tests and exam prep

The official Metal Fabricator (Fitter) Red Seal exam, also called the interprovincial (IP) exam, has 130 questions across 3 topic blocks. Open a block to see its tasks and subtasks.

130
Multiple choice questions
4 hours
Writing time
70%
Pass mark
Major Work Activity% of examReal examPractice bank
APerforms common occupational skills26%34102

A-1 · Performs safety-related functions

6 official exam questions · 18 in the practice bank

  • A-1.01 Maintains safe work environment
  • A-1.02 Uses personal protective equipment (PPE) and safety equipment

A-2 · Uses and maintains tools and equipment

6 official exam questions · 18 in the practice bank

  • A-2.01 Uses hand, power, layout and measuring tools and equipment
  • A-2.02 Uses stationary machinery
  • A-2.03 Maintains cutting and welding equipment
  • A-2.04 Uses access equipment

A-3 · Organizes work

6 official exam questions · 18 in the practice bank

  • A-3.01 Interprets plans, drawings and specifications
  • A-3.02 Organizes project tasks

A-4 · Performs quality assurance throughout fabrication and assembly process

7 official exam questions · 21 in the practice bank

  • A-4.01 Performs visual inspections
  • A-4.02 Verifies measurements, welds and layout
  • A-4.03 Tracks materials and parts for traceability

A-5 · Handles materials

6 official exam questions · 18 in the practice bank

  • A-5.01 Organizes material
  • A-5.02 Determines weights
  • A-5.03 Applies rigging practices
  • A-5.04 Operates material handling equipment

A-6 · Uses communication and mentoring techniques

3 official exam questions · 9 in the practice bank

  • A-6.01 Uses communication techniques
  • A-6.02 Uses mentoring techniques
BFabricates components43%56168

B-7 · Performs layout

24 official exam questions · 72 in the practice bank

  • B-7.01 Performs pattern development
  • B-7.02 Calculates material allowances for various processes
  • B-7.03 Determines dimensions
  • B-7.04 Transfers dimensions
  • B-7.05 Makes templates

B-8 · Cuts materials

17 official exam questions · 51 in the practice bank

  • B-8.01 Cuts material using plasma cutting equipment
  • B-8.02 Cuts material using oxy-fuel cutting equipment
  • B-8.03 Cuts material using shears
  • B-8.04 Cuts material using saws
  • B-8.05 Cuts material using ironworkers
  • B-8.06 Cuts material using computer numerically controlled (CNC) equipment
  • B-8.07 Drills holes
  • B-8.08 Cuts threads
  • B-8.09 Prepares joints

B-9 · Forms materials

15 official exam questions · 45 in the practice bank

  • B-9.01 Forms materials using plate rollers
  • B-9.02 Forms material using shape rollers
  • B-9.03 Forms material using conventional and computer numerically controlled (CNC) press brakes
  • B-9.04 Forms materials using benders
  • B-9.05 Applies heat for forming
CAssembles components31%40120

C-10 · Fits and fastens sub‑components and components

19 official exam questions · 57 in the practice bank

  • C-10.01 Assembles jigs
  • C-10.02 Determines sequence for assembly
  • C-10.03 Assembles sub-components and components
  • C-10.04 Sets fabricated components in place
  • C-10.05 Joins components on-site

C-11 · Performs welding activities

13 official exam questions · 39 in the practice bank

  • C-11.01 Applies heat prior to tack welding
  • C-11.02 Performs tack welding
  • C-11.03 Minimizes welding distortions
  • C-11.04 Applies welding processes
  • C-11.05 Corrects welding distortions

C-12 · Completes project

8 official exam questions · 24 in the practice bank

  • C-12.01 Identifies type of finish
  • C-12.02 Prepares material for finishing

Source: the official Metal Fabricator (Fitter) standard and exam breakdown. Check your own requirements with your province or territory.

Questions about Metal Fabricator (Fitter) exam prep

Study guide
Is there a free Metal Fabricator (Fitter) Red Seal practice test?

Yes. Metal Fabricator (Fitter) Exam 1 is a full practice exam of 130 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.

Is there a Metal Fabricator (Fitter) practice test with answers?

Yes. Every Metal Fabricator (Fitter) practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.

How many questions are on the Metal Fabricator (Fitter) Red Seal exam?

The official Metal Fabricator (Fitter) Red Seal exam has 130 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 91 of 130 questions correct.

What topics are on the Metal Fabricator (Fitter) Red Seal exam?

The published exam breakdown has 3 Major Work Activities (MWAs) or blocks: A, Performs common occupational skills (34 questions); B, Fabricates components (56 questions); C, Assembles components (40 questions).

Can I challenge the Metal Fabricator (Fitter) Red Seal exam without an apprenticeship?

Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 130-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 5,400 in Ontario to 10,800 in Manitoba (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.

How do your Metal Fabricator (Fitter) practice exams follow the official breakdown?

Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.

What are Flashcard Match and Question Match?

Flashcard Match deals a board of Metal Fabricator (Fitter) flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Metal Fabricator (Fitter) practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.

How many Metal Fabricator (Fitter) practice exams are included?

Pass Your Red Seal includes 3 practice exams and 390 original practice questions for Metal Fabricator (Fitter). Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 130 questions on the official exam.

Are Metal Fabricator (Fitter) flashcards included?

Yes. Every Metal Fabricator (Fitter) plan includes 260 flashcards in two exam-weighted sets of 130 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard (RSOS) – Metal Fabricator (Fitter) (2021) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.

Can I try Metal Fabricator (Fitter) practice questions for free?

Yes. Try 12 free Metal Fabricator (Fitter) questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.

How much does Metal Fabricator (Fitter) study access cost?

Study access for Metal Fabricator (Fitter) costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.

Challenge the Metal Fabricator (Fitter) exam without an apprenticeship

How it works

Experienced workers in the metal fabricator trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.

Experience required to challenge the Metal Fabricator (Fitter) Red Seal exam
Province or territory, with its guideHours to challengeApprenticeship and certification
British Columbia7,200Apprenticeship 5,400 hours · voluntary certification
Alberta7,020Apprenticeship 5,400 hours · voluntary certification
Saskatchewan8,100Apprenticeship 5,400 hours · voluntary certification
Manitoba
Steel Fabricator
10,800Apprenticeship 7,200 hours · voluntary certification
Ontario5,400Apprenticeship 5,400 hours · voluntary certification
Quebec
Assembler, metal structure; Welder-fitter
Quebec certificate firstVoluntary certification
New Brunswick8,100Apprenticeship 5,400 hours · voluntary certification
Nova Scotia8,100Apprenticeship 5,400 hours · voluntary certification
Prince Edward Island7,400Apprenticeship 5,400 hours · voluntary certification · PEI’s own Designated Trades page (15 September 2026) shows 10,800 challenger hours and a 7,200-hour apprenticeship; the province’s figure governs.
Newfoundland and Labrador8,100Apprenticeship 5,400 hours · voluntary certification
YukonNot shown
Northwest TerritoriesNo challenge route
NunavutNo challenge route

Source: Ellis Chart, Metal Fabricator (Fitter), published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.