Pass Your Red Seal
Exams

Online Red Seal Exam Preparation, built on official standards

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

Ironworker (Structural/Ornamental)

Built on official standards for your trade

Practice exams split like the real exam.
Every answer explained.

only $14.99

  • Full trade access
  • 12 months
Unlock full access

Pay once, good for a full year.

4
Practice exams
480
Questions
240
Flashcards
1,000+
Flashcard Match
50+
Trade math
100+
Simulations
Try Ironworker (Structural/Ornamental) free12 sample questions now, or Exam 1 with a free account12 sample questionsFree Exam 1

Practice exams

4 exams · 120 questions each

Exam 1 is free. Create a free account and retake it as often as you like, with no expiry. How it works

4 practice exams and 480 original practice questions with answers and explanations, plus 240 flashcards in two exam-weighted sets, for the 120-question Ironworker (Structural/Ornamental) Red Seal exam. Timed or untimed, with pause and resume. 120 questions in the real exam · 4 hours · 70% pass mark.

Ironworker (Structural/Ornamental) sample exam questions

Take them as an exam

12 free practice questions with answers and explanations. No account needed.

Sample 1 Ironworker (Structural/Ornamental), free sample

A small fire involves an energized welding power unit. The emergency plan permits a trained worker to use a portable extinguisher, and the escape route remains clear. Which marking identifies a suitable extinguisher while the equipment is still energized?

Answer 10-B:C carbon dioxide
Why The C classification identifies suitability for energized electrical equipment. A B:C carbon-dioxide extinguisher has that rating. The listed A:B foam unit lacks a C rating. Class D powder is selected for combustible metals, and Class K wet chemical is selected for cooking oils and fats; those markings do not establish suitability for this energized unit. The emergency plan, training and escape conditions still govern whether to attempt extinguishment.
2. The fastening procedure for a Ramset RS22 has established power level 4 after the approved trial-fastening sequence. Which cartridge colour identifies that power level?
Answer Yellow power-load cartridge
Why The RS22 manual identifies power levels 1 through 4 as grey, brown, green and yellow respectively. Yellow is therefore level 4; green is level 3 and brown level 2. Red is a higher colour code and is not one of the four levels specified for this tool. Colour identification does not replace the approved trial sequence, substrate test or fastening procedure.
3. A delivery specified as CSA G40.21 350WT is being checked against its material certificate. Compared with 350W, which additional test requirement must the specified WT category establish?
Answer Charpy V-notch impact energy at the specified test temperature
Why WT steel is produced to specified impact-testing requirements. The purchaser’s notch-toughness category establishes the Charpy V-notch test temperature and energy level, so those requirements must match the certificate and order. The tensile/yield grade and heat chemistry are important but do not establish the WT impact category. Ultrasonic plate soundness is a different examination and is not what the WT suffix specifies.
4. In the Manitowoc Form 6722-A capacity-chart convention, what limits the capacities shown in shaded chart areas?
Answer The structural strength of the crane’s load-carrying components
Why The notes to Form 6722-A state that capacities in shaded areas are based on structural competence. Capacities outside those areas are governed by the chart’s stability basis. Available hoist line pull and wind effects remain important separate constraints, but neither is the meaning of this chart’s shading. A shading convention must be read from the particular chart, not assumed for every crane.
5. A Tirfor TU-series machine advances a few centimetres during one handle stroke, then returns the same distance on the opposite stroke. Which fault best explains this observed pumping behaviour?
Answer Too little lubricant leaves a gripping jaw locked
Why The Tirfor troubleshooting section describes pumping when insufficient lubrication leaves one gripping jaw locked on the rope, preventing normal transfer to the other jaw; the machine moves forward and back the same amount. The manual expressly states that excess lubrication cannot cause this machine or rope to slip. Sheared overload pins instead leave the forward lever moving freely without operating the mechanism. A damaged rope blockage causes a jam rather than this repeated travelling return. Secure or transfer the load as required before approved maintenance.
6. After a lift, an inspection report records 8% localized diameter loss on a Green Pin shackle body, with no distortion, cracks or other defects. Considering only the manufacturer’s maximum wear criterion, how should this reported finding be classified?
Answer Within the 10% original-diameter maximum wear limit
Why Green Pin’s Pocket Pilot states a maximum wear of 10% of the original diameter. The report’s already-computed 8% loss is below that limit. Five percent and two percent are not this published shackle criterion, and 15% would permit excessive wear. This classifies only the stated wear finding; it does not override another defect, a stricter applicable requirement or the rest of the inspection needed before service.
7. A disassembled MLC150-1 #134 jib section without lifting lugs must be moved to its transport position. Where does the manual direct the handling slings to bear?
Answer On the main chords with suitable synthetic lifting slings
Why For the #134 jib sections, the manual specifies synthetic handling slings at the chords, never the lacings, with its minimum sling length and indicated balance locations. Diagonal or horizontal lacing is not a handling point. Backstay pendants belong to the jib suspension system and are not the specified section pickup. If wire-rope or chain slings are used, the manual requires protective covering at the approved chord contacts.
8. A Sokkia Cygnus is in degree angle measurement, with the HSET numeric entry open. The required horizontal direction is 73 degrees 05 minutes 24 seconds. Which entry sets that direction?
Answer Enter 73.0524.
Why Cygnus HSET packs degrees, two minute digits and the seconds digits as D.MMSS. The required entry is 73.0524. Decimal degrees 73.09 represent the same mathematical angle in another encoding, but that is not this HSET input format. Dropping the leading minute zero shifts the fields in 73.524; inserting another zero in 73.00524 also shifts the entered minutes/seconds.
9. What movement does the sliding portion of a floating standing-seam roof clip principally accommodate?
Answer Panel length change along the roof slope.
Why The sliding clip allows the roof panel to expand and contract longitudinally with material-temperature changes while its base remains attached to the substructure. It is not primarily a lateral width-adjustment device at the sidelap. Purlin depth and purlin roll are structural framing conditions rather than the longitudinal panel movement accommodated by the sliding clip.
10. What thickness-profile distinction normally identifies helicoid flighting versus sectional flighting on a screw conveyor?
Answer Helicoid tapers outward; sectional stays uniform.
Why Helicoid flighting is rolled so the outer edge becomes thinner than the root. Sectional flighting is cut from plate and formed with consistent thickness. Reversing the profiles exchanges the manufacturing characteristics. Both-uniform ignores helicoid thinning, and both-tapered incorrectly applies that rolled profile to sectional plate flighting.
11. A carbon-steel clip angle is being separated from a retained beam by manually gouging its weld with an Arcair torch and a standard DC copper-coated carbon electrode. Which polarity and electrode angle to the work surface follow Arcair's normal manual-gouging recommendation?
Answer DC electrode positive; about a 35° push angle
Why For normal manual gouging of carbon steel with the specified DC carbon electrode, Arcair recommends electrode positive and a push angle of about 35° to the work surface. Electrode negative transfers the polarity used for certain other metals to this steel operation. The 70° to 80° range is Arcair's normal severing angle rather than its general manual-gouging recommendation. Electrode negative at that steeper angle combines both substitutions. Special gouging techniques can use different angles; the question asks the manufacturer's normal manual-gouging setup for this weld removal.
12. For this hypothetical job, a replacement spherical roller bearing is mounted on a tapered shaft seat (one sliding surface) using the specified SKF Drive-up Method, without oil injection between mating surfaces. The mounting record for this job stipulates 5.00 MPa for a reference hydraulic nut with a 3600 mm² piston, and 1.20 mm drive-up. The actual compatible nut has a 2400 mm² piston. Which setup correctly interprets that record?
Answer 7.50 MPa; measure 1.20 mm from the hydraulically established start
Why The method first establishes a repeatable starting position using hydraulic-nut pressure, then measures the additional specified drive-up. The smaller piston needs higher pressure for the same axial starting force: 5.00 × 3600/2400 = 7.50 MPa. Measuring 1.20 mm from first contact omits the pressure-established starting datum. Reversing the area ratio gives about 3.33 MPa and too little starting force; using that pressure with first contact as the datum combines both errors. The numerical values are stipulated for this hypothetical job. SKF's guidance provides the mounting method and piston-area correction.

Start free

Interactive simulations

Animated simulations built for Red Seal trades. See inside pumps, transmissions, air brakes, gears and heavy machinery, watch every part move, and interact with each one as it runs.

Diagrams and symbols

Learn to read the diagrams and schematic symbols used in your trade.

How things work

Animated section drawings show what happens inside the equipment as it runs.

Terminology

Learn the correct name and job of every part.

Exam breakdown

Red Seal practice tests and exam prep

The official Ironworker (Structural/Ornamental) Red Seal exam, also called the interprovincial (IP) exam, has 120 questions across 4 topic blocks. Open a block to see its tasks and subtasks.

120
Multiple choice questions
4 hours
Writing time
70%
Pass mark
Major Work Activity% of examReal examPractice bank
APerforms common occupational skills17%2080

A-1 · Maintains safe and healthy workplace

5 official exam questions · 20 in the practice bank

  • A-1.01 Maintains safe work environment
  • A-1.02 Uses personal protective equipment (PPE) and safety equipment
  • A-1.03 Participates in healthy and respectful work environment

A-2 · Uses and maintains tools and equipment

7 official exam questions · 28 in the practice bank

  • A-2.01 Uses hand tools and measuring tools
  • A-2.02 Uses power tools
  • A-2.03 Uses powder-actuated tools
  • A-2.04 Uses mobile elevating work platforms (MEWP)
  • A-2.05 Uses material handling equipment
  • A-2.06 Uses ladders
  • A-2.07 Uses scaffolding
  • A-2.08 Uses surveying equipment
  • A-2.09 Uses welding equipment
  • A-2.10 Uses mechanical cutting equipment
  • A-2.11 Uses thermal cutting equipment

A-3 · Organizes work

6 official exam questions · 24 in the practice bank

  • A-3.01 Organizes materials and supplies
  • A-3.02 Performs layout
  • A-3.03 Uses drawings and documentation
  • A-3.04 Plans tasks

A-4 · Maintains continuous learning

1 official exam question · 4 in the practice bank

  • A-4.01 Upskills in new trade practices and procedures
  • A-4.02 Upskills in emerging technologies

A-5 · Uses communication and mentoring techniques

1 official exam question · 4 in the practice bank

  • A-5.01 Uses communication techniques
  • A-5.02 Uses mentoring techniques
BPerforms rigging, hoisting and positioning, and mobilization, erection, and demobilization of cranes31%38152

B-6 · Plans lift

10 official exam questions · 40 in the practice bank

  • B-6.01 Assesses load
  • B-6.02 Performs pre-lift analysis
  • B-6.03 Selects rigging, hoisting and positioning equipment
  • B-6.04 Secures lift area

B-7 · Rigs, hoists and positions load

14 official exam questions · 56 in the practice bank

  • B-7.01 Inspects rigging, hoisting and positioning equipment
  • B-7.02 Assembles rigging, hoisting and positioning equipment
  • B-7.03 Attaches rigging equipment to load
  • B-7.04 Performs hoisting and positioning operations
  • B-7.05 Secures load before rigging removal

B-8 · Performs post-lift activities

7 official exam questions · 28 in the practice bank

  • B-8.01 Conducts post-lift inspection
  • B-8.02 Disassembles rigging, hoisting and positioning equipment
  • B-8.03 Maintains rigging, hoisting and positioning equipment

B-9 · Performs mobilization, erection and demobilization of cranes

7 official exam questions · 28 in the practice bank

  • B-9.01 Mobilizes telescopic boom cranes
  • B-9.02 Erects lattice boom cranes, tower cranes, derricks and components
  • B-9.03 Performs demobilization and disassembly of cranes
CPerforms erection, assembly, and installation36%43172

C-10 · Installs primary and secondary structural members

20 official exam questions · 80 in the practice bank

  • C-10.01 Uses falsework
  • C-10.02 Attaches structural members
  • C-10.03 Levels, plumbs and aligns structural members
  • C-10.04 Completes installation of structural members

C-11 · Installs ornamental, miscellaneous and steel cladding systems and components

12 official exam questions · 48 in the practice bank

  • C-11.01 Installs curtain walls and window walls
  • C-11.02 Installs miscellaneous components
  • C-11.03 Installs steel cladding and building envelope systems and components

C-12 · Installs conveyors, machinery and equipment

11 official exam questions · 44 in the practice bank

  • C-12.01 Installs material handling systems
  • C-12.02 Performs alignment and commissioning of material handling systems
DPerforms maintenance and upgrading16%1976

D-13 · Decommissions, disassembles and removes structural, ornamental mechanical and miscellaneous components

9 official exam questions · 36 in the practice bank

  • D-13.01 Ensures decommissioning of structure and components
  • D-13.02 Disassembles structural, ornamental, mechanical and miscellaneous components

D-14 · Maintains and repairs components

10 official exam questions · 40 in the practice bank

  • D-14.01 Assesses current condition of components
  • D-14.02 Performs repairs, revisions and reinforcing of components
  • D-14.03 Replaces components
  • D-14.04 Performs preventative maintenance

Source: the official Ironworker (Structural/Ornamental) standard and exam breakdown. Check your own requirements with your province or territory.

Questions about Ironworker (Structural/Ornamental) exam prep

Study guide
Is there a free Ironworker (Structural/Ornamental) Red Seal practice test?

Yes. Ironworker (Structural/Ornamental) Exam 1 is a full practice exam of 120 questions with an explanation for every answer. It is free with a free account in every available trade: unlimited retakes, no expiry and no credit card. The same account plays Question Match with Exam 1. Without an account, try 12 sample questions, math formulas, 20 flashcards and Flashcard Match.

Is there a Ironworker (Structural/Ornamental) practice test with answers?

Yes. Every Ironworker (Structural/Ornamental) practice question comes with its correct answer and an explanation of why it is right. In the free 12-question sample, submit your answers to see the correct answers, the explanations and your score, with no account. Exam 1, free with a free account, and every paid exam also show your score by Major Work Activity. These are original practice questions, not real exam questions.

How many questions are on the Ironworker (Structural/Ornamental) Red Seal exam?

The official Ironworker (Structural/Ornamental) Red Seal exam has 120 multiple-choice questions. Each question has four options and one correct answer. The writing time is four hours and the pass mark is 70%: at least 84 of 120 questions correct.

What topics are on the Ironworker (Structural/Ornamental) Red Seal exam?

The published exam breakdown has 4 Major Work Activities (MWAs) or blocks: A, Performs common occupational skills (20 questions); B, Performs rigging, hoisting and positioning, and mobilization, erection, and demobilization of cranes (38 questions); C, Performs erection, assembly, and installation (43 questions); D, Performs maintenance and upgrading (19 questions).

Can I challenge the Ironworker (Structural/Ornamental) Red Seal exam without an apprenticeship?

Yes. Experienced workers apply to their provincial or territorial authority as trade qualifiers (challengers in New Brunswick, a Trade Equivalency Assessment in Ontario); once it verifies your documented hands-on hours, you write the same 120-question Red Seal exam as a completing apprentice. Quebec has no challenge exam: where it certifies the trade, experienced workers earn a Quebec certificate first, by recognition of their hours or skills, and then enrol in its Red Seal Program. The federal Ellis Chart lists the hours each authority requires for this trade, from 5,400 in New Brunswick to 8,100 in Nova Scotia (read 2026-10-29); the table on this page shows every province. Buying practice material does not make you eligible; the authority decides.

How do your Ironworker (Structural/Ornamental) practice exams follow the official breakdown?

Every practice question maps to an MWA and task, and nearly every question maps to a specific subtask. Numbered practice exams match the published question count for each MWA. Mixed exams combine questions from your trade’s numbered exams; their topic distribution can vary.

What are Flashcard Match and Question Match?

Flashcard Match deals a board of Ironworker (Structural/Ornamental) flashcards on the left and their answers, shuffled, on the right; you match each card to its answer. Question Match does the same with Ironworker (Structural/Ornamental) practice exam questions. Every round deals a new mix, so there are more than 1,000 different rounds of each.

How many Ironworker (Structural/Ornamental) practice exams are included?

Pass Your Red Seal includes 4 practice exams and 480 original practice questions for Ironworker (Structural/Ornamental). Study access includes answers, explanations, practice and timed modes, and results by topic. The practice-bank total covers all available exams; it is separate from the 120 questions on the official exam.

Are Ironworker (Structural/Ornamental) flashcards included?

Yes. Every Ironworker (Structural/Ornamental) plan includes 240 flashcards in two exam-weighted sets of 120 cards. Each set follows the Major Work Activity and task question counts of the official Red Seal Occupational Standard – Ironworker (Structural/Ornamental) (2025) exam breakdown. Review the answer, reasoning, exam trap and standard reference on each card, then use your flashcard score by Major Work Activity to focus your next review.

Can I try Ironworker (Structural/Ornamental) practice questions for free?

Yes. Try 12 free Ironworker (Structural/Ornamental) questions without an account or payment. The sample uses the same format as the full exams: answer one question at a time, navigate between questions, submit your answers, and review your score and explanations. Create a free account to take Exam 1, a full practice exam, in every available trade: unlimited retakes, no expiry and no credit card. Review explanations and your score by MWA, and play Question Match with Exam 1’s questions. Exams 2 onward, mixed exams, paid flashcards and full Flashcard Match and Question Match require paid access for that trade.

How much does Ironworker (Structural/Ornamental) study access cost?

Study access for Ironworker (Structural/Ornamental) costs $8.99 for 1 month or $14.99 for 12 months. Each plan covers this one trade. Pay once, or choose optional renewal with the 1 month plan: $8.99 for the first month, then $5.99 a month. Stop future renewals in your account.

Challenge the Ironworker (Structural/Ornamental) exam without an apprenticeship

How it works

Experienced workers in the ironworker trade can write this Red Seal exam as trade qualifiers once their province verifies enough hands-on experience. The hours below are the figures each authority reports to the federal Ellis Chart, read 29 October 2026; the trade’s own form or profile sets the final rule, and each province’s guide has the forms, fees and steps.

Experience required to challenge the Ironworker (Structural/Ornamental) Red Seal exam
Province or territory, with its guideHours to challengeApprenticeship and certification
British ColumbiaNo challenge route
Alberta7,290Apprenticeship 5,400 hours · compulsory certification
Saskatchewan8,100Apprenticeship 5,400 hours · voluntary certification
ManitobaNot shown
Ontario
Ironworker - Structural and Ornamental
6,000Apprenticeship 6,000 hours · voluntary certification
Quebec
Ironworker
Quebec certificate firstApprenticeship 6,000 hours · compulsory certification
New Brunswick5,400Voluntary certification
Nova Scotia8,100Apprenticeship 5,400 hours · voluntary certification
Prince Edward Island7,400Voluntary certification · PEI’s own Designated Trades page (15 September 2026) shows 6,000 challenger hours; the province’s figure governs.
Newfoundland and Labrador7,200Apprenticeship 5,400 hours · voluntary certification
YukonNot shown
Northwest TerritoriesNo challenge route
NunavutNo challenge route

Source: Ellis Chart, Ironworker (Structural/Ornamental), published by the Canadian Council of Directors of Apprenticeship. Each authority sets and changes its own rules; confirm the current figure on its page before you apply.