MathOnline Red Seal Exam Preparation, built on official standards
Tool and Die Maker formula sheet, conversions and acronyms
MathReference12 formulas · 48 conversions · 31 acronyms
On the exam
- Official formula sheet
- Given at the exam
- Conversions
- Not given: learn them
- Acronyms
- You get the list
- Calculator
- The same calculator as here
On the exam
Formula sheetGiven at the exam
CalculatorThe same as here
Formulas
12 formulasFrom the official Tool and Die Maker formula sheet. The same sheet is printed for you at the exam.
Bend allowance( r + C ) × ( (2 π × angle) / (360) )
Cutting forceL × T × S
Feed rate per minutefpt × N × rpm
Revolutions per minute (imperial)(12 × CS) / (π D)
Revolutions per minute (metric)(1000 × CS) / (π D)
Tap drill sizeMD − P
Time (for lathe)(L) / (fpr × rpm)
Time (for mill)(L) / (fpt × N × rpm)
fprfeed per revolution
fptfeed per tooth
rpmrevolutions per minute
π3.1416
Formulas
Bend allowance( r + C ) × ( (2 π × angle) / (360) )
Cutting forceL × T × S
Feed rate per minutefpt × N × rpm
Revolutions per minute (imperial)(12 × CS) / (π D)
Revolutions per minute (metric)(1000 × CS) / (π D)
Tap drill sizeMD − P
Time (for lathe)(L) / (fpr × rpm)
Time (for mill)(L) / (fpt × N × rpm)
Measurement unit abbreviations
fprfeed per revolution
fptfeed per tooth
rpmrevolutions per minute
Constants
π3.1416
On the exam
ConversionsNot given: learn them
Conversions
48 conversions1 in25.4 mm
1 ft304.8 mm
1 ft0.3048 m
1 yd0.9144 m
1 m3.281 ft
1 m39.37 in
1 km0.6214 mi
1 mi1.609 km
1 km/h0.6214 mph
1 km/h0.2778 m/s
1 mph1.609 km/h
1 m/s3.281 ft/s
1 m/s196.9 ft/min
1 m/min3.281 ft/min
1 psi6.895 kPa
1 kPa0.1450 psi
1 bar100 kPa
1 bar14.50 psi
1 atm101.3 kPa
1 atm14.70 psi
1 in w.c.249.1 Pa
1 ft of water0.4335 psi
1 in Hg3.386 kPa
1 lbf4.448 N
1 kN224.8 lbf
1 kg2.205 lb
1 lb0.4536 kg
1 lb16 oz
1 oz28.35 g
1 t (tonne)1 000 kg
1 t (tonne)2 205 lb
1 short ton2 000 lb
1 short ton907.2 kg
Water1 000 kg/m³ = 1 kg/L
Water62.4 lb/ft³
Water8.34 lb per US gal
Water10.0 lb per imp gal
Steel7 850 kg/m³ = 490 lb/ft³
Steel plate7.85 kg per m² per mm
Concrete2 400 kg/m³ = 150 lb/ft³
1 kg/m³0.06243 lb/ft³
1 lb/ft³16.02 kg/m³
°C to °F× 1.8, then + 32
°F to °C− 32, then ÷ 1.8
°C to K+ 273.15
A difference of 1 °C1.8 °F
Water freezes0 °C = 32 °F
Water boils (sea level)100 °C = 212 °F
Length
1 in25.4 mm
1 ft304.8 mm
1 ft0.3048 m
1 yd0.9144 m
1 m3.281 ft
1 m39.37 in
1 km0.6214 mi
1 mi1.609 km
Speed
1 km/h0.6214 mph
1 km/h0.2778 m/s
1 mph1.609 km/h
1 m/s3.281 ft/s
1 m/s196.9 ft/min
1 m/min3.281 ft/min
Pressure and force
1 psi6.895 kPa
1 kPa0.1450 psi
1 bar100 kPa
1 bar14.50 psi
1 atm101.3 kPa
1 atm14.70 psi
1 in w.c.249.1 Pa
1 ft of water0.4335 psi
1 in Hg3.386 kPa
1 lbf4.448 N
1 kN224.8 lbf
Mass
1 kg2.205 lb
1 lb0.4536 kg
1 lb16 oz
1 oz28.35 g
1 t (tonne)1 000 kg
1 t (tonne)2 205 lb
1 short ton2 000 lb
1 short ton907.2 kg
Density and unit mass
Water1 000 kg/m³ = 1 kg/L
Water62.4 lb/ft³
Water8.34 lb per US gal
Water10.0 lb per imp gal
Steel7 850 kg/m³ = 490 lb/ft³
Steel plate7.85 kg per m² per mm
Concrete2 400 kg/m³ = 150 lb/ft³
1 kg/m³0.06243 lb/ft³
1 lb/ft³16.02 kg/m³
Temperature
°C to °F× 1.8, then + 32
°F to °C− 32, then ÷ 1.8
°C to K+ 273.15
A difference of 1 °C1.8 °F
Water freezes0 °C = 32 °F
Water boils (sea level)100 °C = 212 °F
On the exam
AcronymsYou get the list
Acronyms
31 acronymsThe following acronyms used in this trade may be on its Red Seal exam. They will also be provided with the exam sitting. The official list (PDF)
ANSIAmerican National Standards Institute
CADcomputer-aded design
CAMcomputer-aided manufacturing
CMMcoordinate measuring machine
CNCcomputer numerical control
CRCcutter radius compensation
CRScold rolled steel
CSACanadian Standards Association
Epitch diameter
EDMelectrical discharge machine
FPTfeed per tooth
ft.foot
GD&Tgeometric dimensioning and tolerancing
HRPOhot rolled pickled and oiled
HSShigh speed steel
IDinside diameter
in.inch
ipminches per minute
ISOInternational Organization for Standardization
kgkilogram
lb.pound
lb./cu. ft.pounds per cubic foot
mmmillimetre
Nnumber of teeth
NCnumbered connection
ODoutside diameter
OH&SOccupational Health and Safety
Ppitch
PPEpersonal protective equipment
°Fdegree Fahrenheit
µmmicrometre
°Fdegree Fahrenheit
ANSIAmerican National Standards Institute
CADcomputer-aded design
CAMcomputer-aided manufacturing
CMMcoordinate measuring machine
CNCcomputer numerical control
CRCcutter radius compensation
CRScold rolled steel
CSACanadian Standards Association
Epitch diameter
EDMelectrical discharge machine
FPTfeed per tooth
ft.foot
GD&Tgeometric dimensioning and tolerancing
HRPOhot rolled pickled and oiled
HSShigh speed steel
IDinside diameter
in.inch
ipminches per minute
ISOInternational Organization for Standardization
kgkilogram
lb.pound
lb./cu. ft.pounds per cubic foot
mmmillimetre
Nnumber of teeth
NCnumbered connection
ODoutside diameter
OH&SOccupational Health and Safety
Ppitch
PPEpersonal protective equipment
µmmicrometre