Pass Your Red Seal
MathOnline Red Seal Exam Preparation, built on official standards

Sheet Metal Worker formula sheet, conversions and acronyms

MathReference26 formulas · 60 conversions · 19 acronyms
All math

On the exam

Official formula sheet
Given at the exam
Conversions
Not given: learn them
Acronyms
You get the list
Calculator
The same calculator as here

On the exam

Formula sheetGiven at the exam
CalculatorThe same as here

Formulas

26 formulas

From the official Sheet Metal Worker formula sheet. The same sheet is printed for you at the exam.

Use the π button for calculations. Only round off the final answers.
Pythagorean theorema2 + b2 = c2
Apex height = (large diameter × vertical height) / (large diameter – small diameter)
Area of a circle = π r2
Bend allowance = degrees ( 0.01743 R + 0.0078 t )
Belt length = (π × diameter × degrees) / (360 °)
BTU / h = 1.08 × cfm × temperature difference
C = π × diameter
cfm = area sq. ft. × fpm
(cfm2) / (cfm1) = (rpm2) / (rpm1)
(D2) / (D1) = (rpm1) / (rpm2)
Elbow cut size = tan ( mitre angle ) × centre line radius × ( 2 × # of gores – 2 )
Grille measurement area cfm = (( length × width )) / (144) × (% free area) / (100) × velocity
Grille size area = (cfm) / (fpm) × (100) / (% free area)
Mitre angle = (angle of elbow) / (2 × number of gores – 2)
New rpm = original rpm × (1 + percentage increase / 100)
Pattern angle = (base × 180 °) / (slant side)
Rain cap notch = (R) / (C ∠) × 2 π – π D
S ∠ = (O) / (H)
C ∠ = (A) / (H)
T ∠ = (O) / (A)
p2 / p1 = (N2 / N1)2
Swing point radius = (offset2 + length2) / (4 × offset)
Unknown duct side = (100% free area × duct area) / (known duct side)
Volume = π r2 h
Wraper / belt length = (4 √(( offset2 + length2 )) – length) / (3)
Additional formulas and constants
Use the π button for calculations. Only round off the final answers.
Pythagorean theorema2 + b2 = c2
Apex height = (large diameter × vertical height) / (large diameter – small diameter)
Area of a circle = π r2
Bend allowance = degrees ( 0.01743 R + 0.0078 t )
Belt length = (π × diameter × degrees) / (360 °)
BTU / h = 1.08 × cfm × temperature difference
C = π × diameter
cfm = area sq. ft. × fpm
(cfm2) / (cfm1) = (rpm2) / (rpm1)
(D2) / (D1) = (rpm1) / (rpm2)
Elbow cut size = tan ( mitre angle ) × centre line radius × ( 2 × # of gores – 2 )
Grille measurement area cfm = (( length × width )) / (144) × (% free area) / (100) × velocity
Grille size area = (cfm) / (fpm) × (100) / (% free area)
Mitre angle = (angle of elbow) / (2 × number of gores – 2)
New rpm = original rpm × (1 + percentage increase / 100)
Pattern angle = (base × 180 °) / (slant side)
Rain cap notch = (R) / (C ∠) × 2 π – π D
S ∠ = (O) / (H)
C ∠ = (A) / (H)
T ∠ = (O) / (A)
p2 / p1 = (N2 / N1)2
Swing point radius = (offset2 + length2) / (4 × offset)
Unknown duct side = (100% free area × duct area) / (known duct side)
Volume = π r2 h
Wraper / belt length = (4 √(( offset2 + length2 )) – length) / (3)

On the exam

ConversionsNot given: learn them

Conversions

60 conversions
1 in25.4 mm
1 ft304.8 mm
1 ft0.3048 m
1 yd0.9144 m
1 m3.281 ft
1 m39.37 in
1 km0.6214 mi
1 mi1.609 km
1 ft²144 in²
1 ft²0.0929 m²
1 m²10.76 ft²
1 yd²9 ft²
1 yd²0.8361 m²
1 ha10 000 m²
1 ha2.471 acres
1 acre4 047 m²
1 L/s60 L/min
1 L/s3.6 m³/h
1 L/s15.85 US gpm
1 L/s13.20 imp gpm
1 US gpm3.785 L/min
1 imp gpm4.546 L/min
1 cfm0.4719 L/s
1 cfm1.699 m³/h
1 m³/h0.5886 cfm
1 psi6.895 kPa
1 kPa0.1450 psi
1 bar100 kPa
1 bar14.50 psi
1 atm101.3 kPa
1 atm14.70 psi
1 in w.c.249.1 Pa
1 ft of water0.4335 psi
1 in Hg3.386 kPa
1 lbf4.448 N
1 kN224.8 lbf
1 hp746 W
1 kW1.341 hp
1 kW3 412 Btu/h
1 Btu/h0.2931 W
1 Btu1.055 kJ
1 ton of refrigeration12 000 Btu/h
1 ton of refrigeration3.517 kW
1 kWh3.6 MJ
1 therm100 000 Btu
1 boiler hp33 475 Btu/h
1 kg2.205 lb
1 lb0.4536 kg
1 lb16 oz
1 oz28.35 g
1 t (tonne)1 000 kg
1 t (tonne)2 205 lb
1 short ton2 000 lb
1 short ton907.2 kg
°C to °F× 1.8, then + 32
°F to °C− 32, then ÷ 1.8
°C to K+ 273.15
A difference of 1 °C1.8 °F
Water freezes0 °C = 32 °F
Water boils (sea level)100 °C = 212 °F
Length
1 in25.4 mm
1 ft304.8 mm
1 ft0.3048 m
1 yd0.9144 m
1 m3.281 ft
1 m39.37 in
1 km0.6214 mi
1 mi1.609 km
Area
1 ft²144 in²
1 ft²0.0929 m²
1 m²10.76 ft²
1 yd²9 ft²
1 yd²0.8361 m²
1 ha10 000 m²
1 ha2.471 acres
1 acre4 047 m²
Flow
1 L/s60 L/min
1 L/s3.6 m³/h
1 L/s15.85 US gpm
1 L/s13.20 imp gpm
1 US gpm3.785 L/min
1 imp gpm4.546 L/min
1 cfm0.4719 L/s
1 cfm1.699 m³/h
1 m³/h0.5886 cfm
Pressure and force
1 psi6.895 kPa
1 kPa0.1450 psi
1 bar100 kPa
1 bar14.50 psi
1 atm101.3 kPa
1 atm14.70 psi
1 in w.c.249.1 Pa
1 ft of water0.4335 psi
1 in Hg3.386 kPa
1 lbf4.448 N
1 kN224.8 lbf
Power and energy
1 hp746 W
1 kW1.341 hp
1 kW3 412 Btu/h
1 Btu/h0.2931 W
1 Btu1.055 kJ
1 ton of refrigeration12 000 Btu/h
1 ton of refrigeration3.517 kW
1 kWh3.6 MJ
1 therm100 000 Btu
1 boiler hp33 475 Btu/h
Mass
1 kg2.205 lb
1 lb0.4536 kg
1 lb16 oz
1 oz28.35 g
1 t (tonne)1 000 kg
1 t (tonne)2 205 lb
1 short ton2 000 lb
1 short ton907.2 kg
Temperature
°C to °F× 1.8, then + 32
°F to °C− 32, then ÷ 1.8
°C to K+ 273.15
A difference of 1 °C1.8 °F
Water freezes0 °C = 32 °F
Water boils (sea level)100 °C = 212 °F

On the exam

AcronymsYou get the list

Acronyms

19 acronyms

The following acronyms used in this trade may be on its Red Seal exam. They will also be provided with the exam sitting. The official list (PDF)

ABSacrylonitrile-butadiene-styrene
ASTMAmerican Society for Testing and Materials
CADcomputer-aided design
CSACanadian Standards Association
GMAWgas metal arc welding
GTAWgas tungsten arc welding
HRVheat recovery ventilator
HVACheating, ventilation and air conditioning
IDinside diameter
OCon center
PPEpersonal protective equipment
PVCpolyvinyl chloride
SMACNASheet Metal and Air Conditioning Contractors' National Association
SMAWshielded metal arc welding
TDCtransverse duct connector
TDFtransverse duct flange
ULCUnderwriters Laboratories of Canada
VAVvariable air volume
WHMISWorkplace Hazardous Materials Information System
ABSacrylonitrile-butadiene-styrene
ASTMAmerican Society for Testing and Materials
CADcomputer-aided design
CSACanadian Standards Association
GMAWgas metal arc welding
GTAWgas tungsten arc welding
HRVheat recovery ventilator
HVACheating, ventilation and air conditioning
IDinside diameter
OCon center
PPEpersonal protective equipment
PVCpolyvinyl chloride
SMACNASheet Metal and Air Conditioning Contractors' National Association
SMAWshielded metal arc welding
TDCtransverse duct connector
TDFtransverse duct flange
ULCUnderwriters Laboratories of Canada
VAVvariable air volume
WHMISWorkplace Hazardous Materials Information System