MathOnline Red Seal Exam Preparation, built on official standards
Motorcycle Technician formula sheet, conversions and acronyms
MathReference40 formulas · 63 conversions · 29 acronyms
On the exam
- Official formula sheet
- None for this trade
- Conversions
- Not given: learn them
- Acronyms
- You get the list
- Calculator
- The same calculator as here
On the exam
Formula sheetNone for this trade
CalculatorThe same as here
Formulas
40 formulasThe Red Seal Program does not publish a formula sheet for this trade, so these are the formulas its math lessons use.
°F = 1.8 × °C + 32
°C = (°F − 32) / 1.8
K = °C + 273.15
Δ°F = 1.8 × Δ°C
1 US gal = 3.785411784 L; 1 Imperial gal = 4.54609 L
RectangleA = LW; perimeter = 2(L+W)
TriangleA = bh/2; perimeter = a+b+c
CircleA = πr² = πd²/4; C = πd
BoxV = LWH
CylinderV = πr²h
SphereV = 4πr³/3
Cone or pyramidV = base area × h/3
Triangular wedgeV = LWH/2
1 m³ = 1000 L
Cylinder side = 2πrh
Cylinder with one end = 2πrh + πr²
Closed cylinder = 2πrh + 2πr²
Closed box = 2(LW + LH + WH)
Open box = LW + 2LH + 2WH
Sphere = 4πr²
Cone lateral area = πrs
Pyramid lateral area = perimeter of base × slant height / 2
c² = a² + b²
sin θ = opposite/hypotenuse
cos θ = adjacent/hypotenuse
tan θ = opposite/adjacent
θ = atan(rise/run)
Offset travel = offset / sin θ
Arc length = πrθ/180 = πdθ/360
Sector pattern angle = 360 × base radius / slant radius
Equivalent formpattern angle = 180 × base diameter / slant radius
Grade (%) = rise/run × 100
Rise = run × unit rise/unit run
Symmetrical roof run = span/2
Rafter line length = √(run² + rise²)
Unit line length (per 12 of run) = √(12² + unit rise²)
New quantity = original quantity × scale factor
Scale factor = required yield / original yield
With p% addedfinal = original × (1+p/100)
Baker’s percentage = ingredient mass / flour mass × 100
Temperature and unit conversion
°F = 1.8 × °C + 32
°C = (°F − 32) / 1.8
K = °C + 273.15
Δ°F = 1.8 × Δ°C
1 US gal = 3.785411784 L; 1 Imperial gal = 4.54609 L
Areas, perimeter and circumference
RectangleA = LW; perimeter = 2(L+W)
TriangleA = bh/2; perimeter = a+b+c
CircleA = πr² = πd²/4; C = πd
Volumes, capacity and material quantities
BoxV = LWH
CylinderV = πr²h
SphereV = 4πr³/3
Cone or pyramidV = base area × h/3
Triangular wedgeV = LWH/2
1 m³ = 1000 L
Surface area of vessels and insulation
Cylinder side = 2πrh
Cylinder with one end = 2πrh + πr²
Closed cylinder = 2πrh + 2πr²
Closed box = 2(LW + LH + WH)
Open box = LW + 2LH + 2WH
Sphere = 4πr²
Cone lateral area = πrs
Pyramid lateral area = perimeter of base × slant height / 2
Pythagoras, trigonometry and offsets
c² = a² + b²
sin θ = opposite/hypotenuse
cos θ = adjacent/hypotenuse
tan θ = opposite/adjacent
θ = atan(rise/run)
Offset travel = offset / sin θ
Arc lengths and developed patterns
Arc length = πrθ/180 = πdθ/360
Sector pattern angle = 360 × base radius / slant radius
Equivalent formpattern angle = 180 × base diameter / slant radius
Grade, roof rise and run
Grade (%) = rise/run × 100
Rise = run × unit rise/unit run
Symmetrical roof run = span/2
Rafter line length = √(run² + rise²)
Unit line length (per 12 of run) = √(12² + unit rise²)
Percentages, recipe scaling and quantities
New quantity = original quantity × scale factor
Scale factor = required yield / original yield
With p% addedfinal = original × (1+p/100)
Baker’s percentage = ingredient mass / flour mass × 100
On the exam
ConversionsNot given: learn them
Conversions
63 conversions1 in³16.39 cm³
1 L61.02 in³
1 US qt0.9464 L
1 US gal3.785 L
mpg (US)235.2 ÷ L/100 km
mpg (imp)282.5 ÷ L/100 km
1 lb·ft1.356 N·m
1 hp0.746 kW
1 mph1.609 km/h
1 psi6.895 kPa
1 N·m0.7376 lb·ft
1 N·m8.851 lb·in
1 lb·ft1.356 N·m
1 lb·ft12 lb·in
1 lb·in0.1130 N·m
1 kgf·m9.807 N·m
1 psi6.895 kPa
1 kPa0.1450 psi
1 bar100 kPa
1 bar14.50 psi
1 atm101.3 kPa
1 atm14.70 psi
1 in w.c.249.1 Pa
1 ft of water0.4335 psi
1 in Hg3.386 kPa
1 lbf4.448 N
1 kN224.8 lbf
1 tsp5 mL
1 tbsp15 mL
1 metric cup250 mL
1 US cup237 mL (8 US fl oz)
1 US fl oz29.57 mL
1 imp fl oz28.41 mL
1 US pint473 mL
1 US quart946 mL
1 US gal3.785 L
1 m³1 000 L
1 m³35.31 ft³
1 m³1.308 yd³
1 yd³27 ft³
1 ft³28.32 L
1 ft³7.481 US gal
1 ft³6.229 imp gal
1 L0.2642 US gal
1 L0.2200 imp gal
1 US gal3.785 L
1 imp gal4.546 L
1 in³16.39 mL
°C to °F× 1.8, then + 32
°F to °C− 32, then ÷ 1.8
°C to K+ 273.15
A difference of 1 °C1.8 °F
Water freezes0 °C = 32 °F
Water boils (sea level)100 °C = 212 °F
Power (W)V × A
1 kW1 000 W
1 kVA1 000 VA
1 hp746 W
1 mA0.001 A
1 mV0.001 V
1 kΩ1 000 Ω
1 MΩ1 000 000 Ω
1 kWh1 kW for 1 hour
Vehicle and engine
1 in³16.39 cm³
1 L61.02 in³
1 US qt0.9464 L
1 US gal3.785 L
mpg (US)235.2 ÷ L/100 km
mpg (imp)282.5 ÷ L/100 km
1 lb·ft1.356 N·m
1 hp0.746 kW
1 mph1.609 km/h
1 psi6.895 kPa
Torque
1 N·m0.7376 lb·ft
1 N·m8.851 lb·in
1 lb·ft1.356 N·m
1 lb·ft12 lb·in
1 lb·in0.1130 N·m
1 kgf·m9.807 N·m
Pressure and force
1 psi6.895 kPa
1 kPa0.1450 psi
1 bar100 kPa
1 bar14.50 psi
1 atm101.3 kPa
1 atm14.70 psi
1 in w.c.249.1 Pa
1 ft of water0.4335 psi
1 in Hg3.386 kPa
1 lbf4.448 N
1 kN224.8 lbf
Small volumes
1 tsp5 mL
1 tbsp15 mL
1 metric cup250 mL
1 US cup237 mL (8 US fl oz)
1 US fl oz29.57 mL
1 imp fl oz28.41 mL
1 US pint473 mL
1 US quart946 mL
1 US gal3.785 L
Volume
1 m³1 000 L
1 m³35.31 ft³
1 m³1.308 yd³
1 yd³27 ft³
1 ft³28.32 L
1 ft³7.481 US gal
1 ft³6.229 imp gal
1 L0.2642 US gal
1 L0.2200 imp gal
1 US gal3.785 L
1 imp gal4.546 L
1 in³16.39 mL
Temperature
°C to °F× 1.8, then + 32
°F to °C− 32, then ÷ 1.8
°C to K+ 273.15
A difference of 1 °C1.8 °F
Water freezes0 °C = 32 °F
Water boils (sea level)100 °C = 212 °F
Electrical
Power (W)V × A
1 kW1 000 W
1 kVA1 000 VA
1 hp746 W
1 mA0.001 A
1 mV0.001 V
1 kΩ1 000 Ω
1 MΩ1 000 000 Ω
1 kWh1 kW for 1 hour
On the exam
AcronymsYou get the list
Acronyms
29 acronymsThe following acronyms used in this trade may be on its Red Seal exam. They will also be provided with the exam sitting. The official list (PDF)
ABSanti-lock brake system
ACalternating current
AGMabsorbed glass mat
BDCbottom dead centre
CANcontroller area network
CDIcapacitor discharge ignition
CVconstant velocity
CVTcontinuous variable transmission
DCdirect current
DOHCdual overhead camshaft
DOTDepartment of Transportation
ECMelectronic control module
ECUelectronic control unit
EFIelectronic fuel injection
GPSglobal positioning system
IATintake air temperature
LEDlight emitting diode
MAPmanifold absolute pressure
MILmalfunction indicator lamp
OBDonboard diagnostic
OEMoriginal equipment manufacturer
PDIpre-delivery inspection
PHpotential of hydrogen
PPEpersonal protective equipment
rpmrevolutions per minute
TCItransistor controlled ignitor
TDCtop dead centre
TPMStire pressure monitoring system
TPSthrottle position sensor
ABSanti-lock brake system
ACalternating current
AGMabsorbed glass mat
BDCbottom dead centre
CANcontroller area network
CDIcapacitor discharge ignition
CVconstant velocity
CVTcontinuous variable transmission
DCdirect current
DOHCdual overhead camshaft
DOTDepartment of Transportation
ECMelectronic control module
ECUelectronic control unit
EFIelectronic fuel injection
GPSglobal positioning system
IATintake air temperature
LEDlight emitting diode
MAPmanifold absolute pressure
MILmalfunction indicator lamp
OBDonboard diagnostic
OEMoriginal equipment manufacturer
PDIpre-delivery inspection
PHpotential of hydrogen
PPEpersonal protective equipment
rpmrevolutions per minute
TCItransistor controlled ignitor
TDCtop dead centre
TPMStire pressure monitoring system
TPSthrottle position sensor