Pass Your Red Seal
MathOnline Red Seal Exam Preparation, built on official standards

Auto Body and Collision Technician formula sheet and conversions

MathReference40 formulas · 47 conversions · 29 acronyms
All math

On the exam

Official formula sheet
None for this trade
Conversions
Not given: learn them
Acronyms
You get the list
Calculator
The same calculator as here

On the exam

Formula sheetNone for this trade
CalculatorThe same as here

Formulas

40 formulas

The Red Seal Program does not publish a formula sheet for this trade, so these are the formulas its math lessons use.

°F = 1.8 × °C + 32
°C = (°F − 32) / 1.8
K = °C + 273.15
Δ°F = 1.8 × Δ°C
1 US gal = 3.785411784 L; 1 Imperial gal = 4.54609 L
RectangleA = LW; perimeter = 2(L+W)
TriangleA = bh/2; perimeter = a+b+c
CircleA = πr² = πd²/4; C = πd
BoxV = LWH
CylinderV = πr²h
SphereV = 4πr³/3
Cone or pyramidV = base area × h/3
Triangular wedgeV = LWH/2
1 m³ = 1000 L
Cylinder side = 2πrh
Cylinder with one end = 2πrh + πr²
Closed cylinder = 2πrh + 2πr²
Closed box = 2(LW + LH + WH)
Open box = LW + 2LH + 2WH
Sphere = 4πr²
Cone lateral area = πrs
Pyramid lateral area = perimeter of base × slant height / 2
c² = a² + b²
sin θ = opposite/hypotenuse
cos θ = adjacent/hypotenuse
tan θ = opposite/adjacent
θ = atan(rise/run)
Offset travel = offset / sin θ
Arc length = πrθ/180 = πdθ/360
Sector pattern angle = 360 × base radius / slant radius
Equivalent formpattern angle = 180 × base diameter / slant radius
Grade (%) = rise/run × 100
Rise = run × unit rise/unit run
Symmetrical roof run = span/2
Rafter line length = √(run² + rise²)
Unit line length (per 12 of run) = √(12² + unit rise²)
New quantity = original quantity × scale factor
Scale factor = required yield / original yield
With p% addedfinal = original × (1+p/100)
Baker’s percentage = ingredient mass / flour mass × 100
Temperature and unit conversion
°F = 1.8 × °C + 32
°C = (°F − 32) / 1.8
K = °C + 273.15
Δ°F = 1.8 × Δ°C
1 US gal = 3.785411784 L; 1 Imperial gal = 4.54609 L
Areas, perimeter and circumference
RectangleA = LW; perimeter = 2(L+W)
TriangleA = bh/2; perimeter = a+b+c
CircleA = πr² = πd²/4; C = πd
Volumes, capacity and material quantities
BoxV = LWH
CylinderV = πr²h
SphereV = 4πr³/3
Cone or pyramidV = base area × h/3
Triangular wedgeV = LWH/2
1 m³ = 1000 L
Surface area of vessels and insulation
Cylinder side = 2πrh
Cylinder with one end = 2πrh + πr²
Closed cylinder = 2πrh + 2πr²
Closed box = 2(LW + LH + WH)
Open box = LW + 2LH + 2WH
Sphere = 4πr²
Cone lateral area = πrs
Pyramid lateral area = perimeter of base × slant height / 2
Pythagoras, trigonometry and offsets
c² = a² + b²
sin θ = opposite/hypotenuse
cos θ = adjacent/hypotenuse
tan θ = opposite/adjacent
θ = atan(rise/run)
Offset travel = offset / sin θ
Arc lengths and developed patterns
Arc length = πrθ/180 = πdθ/360
Sector pattern angle = 360 × base radius / slant radius
Equivalent formpattern angle = 180 × base diameter / slant radius
Grade, roof rise and run
Grade (%) = rise/run × 100
Rise = run × unit rise/unit run
Symmetrical roof run = span/2
Rafter line length = √(run² + rise²)
Unit line length (per 12 of run) = √(12² + unit rise²)
Percentages, recipe scaling and quantities
New quantity = original quantity × scale factor
Scale factor = required yield / original yield
With p% addedfinal = original × (1+p/100)
Baker’s percentage = ingredient mass / flour mass × 100

On the exam

ConversionsNot given: learn them

Conversions

47 conversions
1 in25.4 mm
1 ft304.8 mm
1 ft0.3048 m
1 yd0.9144 m
1 m3.281 ft
1 m39.37 in
1 km0.6214 mi
1 mi1.609 km
1 ft²144 in²
1 ft²0.0929 m²
1 m²10.76 ft²
1 yd²9 ft²
1 yd²0.8361 m²
1 ha10 000 m²
1 ha2.471 acres
1 acre4 047 m²
1 kg2.205 lb
1 lb0.4536 kg
1 lb16 oz
1 oz28.35 g
1 t (tonne)1 000 kg
1 t (tonne)2 205 lb
1 short ton2 000 lb
1 short ton907.2 kg
°C to °F× 1.8, then + 32
°F to °C− 32, then ÷ 1.8
°C to K+ 273.15
A difference of 1 °C1.8 °F
Water freezes0 °C = 32 °F
Water boils (sea level)100 °C = 212 °F
1 psi6.895 kPa
1 kPa0.1450 psi
1 bar100 kPa
1 bar14.50 psi
1 atm101.3 kPa
1 atm14.70 psi
1 in w.c.249.1 Pa
1 ft of water0.4335 psi
1 in Hg3.386 kPa
1 lbf4.448 N
1 kN224.8 lbf
1 N·m0.7376 lb·ft
1 N·m8.851 lb·in
1 lb·ft1.356 N·m
1 lb·ft12 lb·in
1 lb·in0.1130 N·m
1 kgf·m9.807 N·m
Length
1 in25.4 mm
1 ft304.8 mm
1 ft0.3048 m
1 yd0.9144 m
1 m3.281 ft
1 m39.37 in
1 km0.6214 mi
1 mi1.609 km
Area
1 ft²144 in²
1 ft²0.0929 m²
1 m²10.76 ft²
1 yd²9 ft²
1 yd²0.8361 m²
1 ha10 000 m²
1 ha2.471 acres
1 acre4 047 m²
Mass
1 kg2.205 lb
1 lb0.4536 kg
1 lb16 oz
1 oz28.35 g
1 t (tonne)1 000 kg
1 t (tonne)2 205 lb
1 short ton2 000 lb
1 short ton907.2 kg
Temperature
°C to °F× 1.8, then + 32
°F to °C− 32, then ÷ 1.8
°C to K+ 273.15
A difference of 1 °C1.8 °F
Water freezes0 °C = 32 °F
Water boils (sea level)100 °C = 212 °F
Pressure and force
1 psi6.895 kPa
1 kPa0.1450 psi
1 bar100 kPa
1 bar14.50 psi
1 atm101.3 kPa
1 atm14.70 psi
1 in w.c.249.1 Pa
1 ft of water0.4335 psi
1 in Hg3.386 kPa
1 lbf4.448 N
1 kN224.8 lbf
Torque
1 N·m0.7376 lb·ft
1 N·m8.851 lb·in
1 lb·ft1.356 N·m
1 lb·ft12 lb·in
1 lb·in0.1130 N·m
1 kgf·m9.807 N·m

On the exam

AcronymsYou get the list

Acronyms

29 acronyms

The following acronyms used in this trade may be on its Red Seal exam. They will also be provided with the exam sitting. The official list (PDF)

A/Cair conditioning
ABSacrylonitrile butadiene styrene
DAdouble action
DTCdiagnostic trouble code
DVOMdigital volt ohmmeter
FRPfibre reinforced plastic
HSLAhigh-strength low-alloy steel
HSShigh strength steel
ISOInternational Organization for Standardization
LEDlight emitting diode
MIGmetal inert gas
MILmalfunction indicator lamp
NIOSHNational Institute for Occupational Safety and Health
NVHnoise, vibration and harshness
OBDonboard diagnostics
OEMoriginal equipment manufacturer
PPpolypropylene
PPEpersonal protective equipment
PURthermoset polyurethane
SDSsafety data sheet
SMCsheet moulded compound
SOPstandard operating procedure
SPRself-piercing rivet
SRSsupplemental restraint system
STRSWsqueeze type resistance spot welding
TPOthermoplastic polyolefin
UHSSultra high strength steel
UVultraviolet
VINvehicle identification number
A/Cair conditioning
ABSacrylonitrile butadiene styrene
DAdouble action
DTCdiagnostic trouble code
DVOMdigital volt ohmmeter
FRPfibre reinforced plastic
HSLAhigh-strength low-alloy steel
HSShigh strength steel
ISOInternational Organization for Standardization
LEDlight emitting diode
MIGmetal inert gas
MILmalfunction indicator lamp
NIOSHNational Institute for Occupational Safety and Health
NVHnoise, vibration and harshness
OBDonboard diagnostics
OEMoriginal equipment manufacturer
PPpolypropylene
PPEpersonal protective equipment
PURthermoset polyurethane
SDSsafety data sheet
SMCsheet moulded compound
SOPstandard operating procedure
SPRself-piercing rivet
SRSsupplemental restraint system
STRSWsqueeze type resistance spot welding
TPOthermoplastic polyolefin
UHSSultra high strength steel
UVultraviolet
VINvehicle identification number